• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.240-244
• /
• 2011

The high cost of crystalline silicon solar cells has been considered as one of the major obstacles to their terrestrial applications. Spin on doping (SOD) is presented as a useful process for the manufacturing of low cost solar cells. Phosphorus (P509) was used as an n-type emitters of solar cells. N-type emitters were formed on p-type EFG ribbon Si wafers by using a SOD at different spin speed (1,000~4,000 rpm), diffusion temperatures ($800^{\circ}C{\sim}950^{\circ}C$), and diffusion time (5~30 min) in $N_2+O_2$ atmosphere. With optimum condition, we were able to achieve cell efficiency of 14.1%.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.105-110
• /
• 2011

The doping procedure in crystalline silicon solar cell fabrication usually contains oxygen injection during drive-in process and removal of phosphorous silicate glass(PSG). In this paper, we studied the effect of oxygen injection and PSG on conversion efficiency of solar cell. The mono crystalline silicon wafers with $156{\times}156mm^2$, $200{\mu}m$, $0.5-3.0{\Omega}{\cdot}cm$ and p-type were used. After etching $7{\mu}m$ of the surface to form the pyramidal structure, the P(phosphorous) was injected into silicon wafer using diffusion furnace to make the emitter layer. After then, the silicon nitride was deposited by the PECVD with 80 nm thickness and 2.1 refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$880^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Solar cells with four different types were fabricated with/without oxygen injection and PSG removal. Solar cell that injected oxygen during the drive-in process and removed PSG after doping process showed the 17.9 % conversion efficiency which is best in this study. This solar cells showed $35.5mA/cm^2$ of the current density, 632 mV of the open circuit voltage and 79.5 % of the fill factor.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.2
• /
• pp.11-17
• /
• 2013

Silicon nitride($SiN_x:H$) deposited by radio frequency plasma enhanced chemical vapor deposition(RF-PECVD) is commonly used for anti-reflection coating and passivation in crystalline silicon solar cell fabrication. In this paper, characteristics of the deposited silicon nitride was studied with change of working pressure, deposition temperature, gas ratio of $NH_3$ and $SiH_4$, and RF power during deposition. The deposition rate, refractive index and effective lifetime were analyzed. The (100) p-type silicon wafers with one-side polished, $660-690{\mu}m$, and resistivity $1-10{\Omega}{\cdot}cm$ were used. As a result, when the working pressure increased, the deposition rate of SiNx was increased while the effective life time for the $SiN_x$-deposited wafer was decreased. The result regarding deposition temperature, gas ratio and RF power changes would be explained in detail below. In this paper, the optimized condition in silicon nitride deposition for silicon solar cell was obtained as 1.0 Torr for the working pressure, $400^{\circ}C$ for deposition temperature, 500 W for RF power and 0.88 for $NH_3/SiH_4$ gas ratio. The silicon nitride layer deposited in this condition showed the effective life time of > $1400{\mu}s$ and the surface recombination rate of 25 cm/s. The crystalline silicon solar cell fabricated with this SiNx coating showed 18.1% conversion efficiency.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2020

Copper Oxide (CuO) films were deposited on the n-type silicon wafer by rf magnetron sputtering for heterojunction solar cells. And then the samples were treated as a function of the annealing temperature (300-600℃) in a vacuum. Their electrical, optical and structural properties of the fabricated heterojunction solar cells were then investigated and the power conversion efficiencies (PCE) of the fabricated p-type copper oxide/n-type Si heterojunction cells were measured using solar simulator. After being treated at temperature of 500℃, the solar cells with CuO film have PCE of 0.43%, Current density of 5.37mA/㎠, Fill Factor of 39.82%.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.243-247
• /
• 2012

The paper focuses on an anti-reflection (AR) coating deposited by PECVD in silicon solar cell fabrication. AR coating is effective to reduce the reflection of the light on the silicon wafer surface and then increase substantially the solar cell conversion efficiency. In this work, we carried out experiments to optimize double AR coating layer with silicon nitride and silicon oxide for the silicon solar cells. The p-type mono crystalline silicon wafers with $156{\times}156mm^2$ area, 0.5-3 ${\Omega}{\cdot}cm$ resistivity, and $200{\mu}m$ thickness were used. All wafers were textured in KOH solution, doped with $POCl_3$ and removed PSG before ARC process. The optimized thickness of each ARC layer was calculated by theoretical equation. For the double layer of AR coating, silicon nitride layer was deposited first using $SiH_4$ and $NH_3$, and then silicon oxide using $SiH_4$ and $N_2O$. As a result, reflectance of $SiO_2/SiN_x$ layer was lower than single $SiN_x$ and then it resulted in increase of short-circuit current and conversion efficiency. It indicates that the double AR coating layer is necessary to obtain the high efficiency solar cell with PECVD already used in commercial line.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.298-304
• /
• 2003

IPMC(Ionic Polymer-Metal Composite) is a highly sensitive actuator that shows a large deformation in presence of low applied voltage. Generally, IPMC can be fabricated by electroless plating of platinum on both sides of a Nafion (perfluorosulfonic acid) film. When a commercial Nafion film is used as a base structure of the IPMC membrane, the micro-pump structure and the IPMC membrane are fabricated separately and then later assembled, which makes the fabrication inefficient. Therefore, fabrication of an IPMC membrane and the micro-pump structure on a single wafer without the need of assembly have been developed. The silicon wafer was partially etched to hold liquid Nafion to be casted and a 60-${\mu}{\textrm}{m}$ thick IPMC membrane was realized. IPMC membranes with various size were fabricated by casting and they showed 4-2${\mu}{\textrm}{m}$ displacements from $4mm{\times}4mm$ , $6mm{\times}6mm$, $8mm{\times}8mm$ membranes at the applied voltage ranging from 2Vp-p to 5Vp-p at 0.5Hz. The displacement of the fabricated IPMC membranes is fairly proportional to the membrane area and the applied voltage.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.32-33
• /
• 1995

고집적 회로 제작에 사용되는 P-형 실리콘 웨이퍼 내부에 존재하는 금속불순물을 소수캐리어의 여기변화 등을 이용하는 정성적인 SPV 측정과 정량적인 DLTS 측정을 통해서 비교, 분석하였다. 반도체공정상 중요한 오염원이며, 분석이 쉬운 Fe을 주 오염원으로 하여 분석한 결과 SPV와 DLTS에 의한 Fe는 상호연관관계가 성립하며, p-형 실리콘 웨이퍼내의 Fe, FeB 거동을 20$0^{\circ}C$ quenching으로 관찰할 수 있었으며, 각각의 에너지준위는 0.45 및 0.11eV 임을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.366-366
• /
• 2009

후면접합 태양전지는 상용 태양전지의 수평전류 손실(lateral current loss) 이 없으며, 전면전극에 의해 발생하는 그림자 손실(shading loss) 줄인 고효율 태양전지의 하나이다. 생성된 반송자가 후면에 위치한 전극에서 수집되기 때문에 효율향상을 위해서는 불순물에 의한 재결합을 줄이는 것이 중요하다. 따라서 Gettering 은 높은 소수반송자 수명(life-time)을 가지는 고품위 실리콘 기판은 고효율 실리콘태양전지 제작을 위한 중요 요소 기술이다. 본 연구에서는 n-type c-Si 기판을 이용한 고효율 실리콘 이종접합 태양전지제작을 위해 external gettering 공정을 이용하여 고품위 실리콘 기판을 제작하였다. POC13 doping process 의 온도, 시간을 변화시킴으로써 이에 따른 변화를 관찰하였다. 주사전자현미경(SEM)를 통해 etch pit 을 확인 했으며,Four point probe 를 통해 면저항을 측정, 인(P)의 농도를 계산 하였다. 계산된 면저항을 통해 인(P)의 확산 깊이를 계산하였다. Iodine passivation 된 시편을 Qusi-steady state photoconductance (QSSPC)를 이용하여 소수반송자 수명을 측정함으로써 gettering 에 의한 bulk lifetime 향상 효과를 관찰하였다.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1463-1465
• /
• 1994

The electrical characteristics of $Al/Ta_2O_5/Si$ metal-oxide-semiconductor (MOS) capacitors were studied. $Ta_2O_5$ films on p-type silicon had been prepared by ionized cluster beam epitaxy technique (ICBE). This $Ta_2O_5$ films have low leakage current, high breakdown strength and low flat band shift. In this research, a single crystalline cpitaxial film of $Ta_2O_5$ has been grown on p-Si wafer using an ICBE technique. The native oxide layer ($SiO_2$) on the silicon substrate was removed below $500^{\circ}C$ by use of an accelerated arsenic ion beam, instead of a high temperature deposition. $Ta_2O_5$ films formed by ICBE technique can be received considerable attention for applications to coupling capacitors, gate dielectrics in MOS devices, and memory storage capacitor insulator because of their high dielectric constants above 20 and low temperature process.

• Journal of Sensor Science and Technology
• /
• v.4 no.1
• /
• pp.3-8
• /
• 1995

n-ITO/p-PSL heterojunction photodetector have been fabricated on the Si wafer by using ITO(indium tin oxide) and PSL(porous silicon layer). They were anodized selectively by using silicon nitride and Ni-Cr/Au and were passivated by using ITO as well as being isolated by using mesa structure. With white light from 0 to 3000 Lux, the photocurrent varied linearly with incident light intensity. The reverse characteristics of fabricated devices were very stable up to a bias voltage of -40V and dark current density was about $40nA/mm^{2}$. When the device was exposed by Xe lamp whose wavelength range from 400nm to 1100nm, the maximum photo responsivity was about 0.6A/W between 600 and 700nm. Variation of the characteristics of fabricated devices after 5 weeks was negligible.