• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.269-276
• /
• 2009

Antimony doped tin oxide ($SnO_2:Sb$) films, which are used as the front contact and back reflector of thin film solar cells, have been deposited by d,c, magnetron sputtering. The dependence of electrical and optical properties of the films on the preparation conditions, such as $O_2$ gas ratio, substrate temperature, annealing temperature was investigated. The sputter gas composition was found to affect the properties of the films. With incorporating $O_2$ gas, the electrical and optical properties of films significantly were improved. The minimum resistivity and optical transmittance over 80 % in visible region were obtained at the oxygen concentration of 30 %, When the substrate temperature was higher, the resistivity of $SnO_2:Sb$ films was decreased, while the absorption edge shifted to shorter wavelength, indicating higher optical band gap. Heat treatment over $600^{\circ}C$ resulted in poorer electrical and optical properties due to SnO phase (102) plane.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.231.2-231.2
• /
• 2014

훌륭한 전기적 특성을 갖는 ZnO 기반의 산화물 반도체 박막트랜지스터(TFT)는 AMOLEDs에 적용될 수 있다. 하지만 이러한 장점에도 불구하고 산화물 반도체 TFT소자에 전압이 인가되었을 때 문턱 전압이 이동하게 되는 안정성 문제를 갖는다. 따라서 이를 해결하기 위한 연구가 널리 진행 되고 있다. 본 연구소에서는 고압 분위기 열처리를 통해 안정성의 원인으로 작용할 수 있는 산소공공(Oxygen vacancy)을 감소시키는 연구를 진행하였다. 산화물 반도체 TFT소자의 안정성을 향상시키는 대표적인 분위기 열처리로는 산소 고압 열처리(HPA)가 있으며, 또한 H2O 기체를 사용한 열처리를 통해 TFT소자의 안정성을 높일 수 있다는 연구 결과가 보고된 바 있다. 본 연구에서는 IGZO TFT소자에 H2O보다 더 큰 반응성을 갖는 산화제인 H2O2 기체를 사용한 HPA를 통해 positive bias stress(PBS) 및 negative bias illumination stress(NBIS) 조건에서 안정성이 향상됨을 확인하였고 이를 H2O 기체를 사용한 경우와 비교하였다. 그 결과 H2O2 기체를 산화제로 사용할 때 기존 H2O 기체에 비해 효과적인 PBS 및 NBIS 신뢰성 개선을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.558-561
• /
• 2001

Vanadium oxide ($VO_x$) thin films are very good candidate material for uncooled infrared (IR) detectors due to their high temperature coefficient of resistance (TCR) at room temperature. But, the deposition of $VO_x$ thin films showing good electrical properties is very difficult in micro bolometer fabrication process using sacrificial layer removal because of its low process temperature and thickness of thin films less than $1000{\AA}$. This paper presents a new fabrication process of $VO_x$ thin films having high TCR and low resistance. Through sandwich structure of $VO_{x}(100{\AA})/V(80{\AA})/VO_{x}(500{\AA})$ by sputter method and post-annealing at oxygen ambient, we have achieved high TCR more than $-2%/^{\circ}C$ and low resistance less than $10K\Omega$ at room temperature.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.158-161
• /
• 2006

Superconducting YBCO films were successfully fabricated by MOD process using chemically modified precursor solution. In this study, a chemically modified precursor solution for MOD processing was synthesized using metal-organic salts and organic additives. It was shown that crack-free and uniform precursor films were formed after calcination in humidified Oxygen atmosphere. Less than 3 hours are required to finish the calcination process. XRD measurement shows that $BaF_2,\;CuO,\;Y_2O_3$ are major constituent of precursor films. Furthermore, YBCO films without any secondary phases were successfully fabricated after annealing in wet $Ar/O_2$ atmosphere. The YBCO film prepared on a $LaAlO_3$ single crystal substrate ($10mm{\times}10mm$) gives transport $I_c$ of 10A at 77K. This chemical modification approach is a possible candidate for improving MOD-processing of YBCO coated conductor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.552-552
• /
• 2012

We fabricated reduced graphene oxide field-effect transistor (RGO-FET) on glass for highly sensitive temperature and IR detection. The device has the channels of RGO responsive to physical stimuli such as temperature and IR. The RGO sensing layers are fabricated from exfoliated graphene oxide sheets that are deposited to form a thin continuous network by electrostatic assembly. These graphene oxide networks are reduced toward reduce graphene oxide by exposure to a hydrazine hydrate vapor. To improve performance and eliminate interferences from oxygen and water vapor absorption to electrical properties of RGO-FET, the sensor devices were encapsulated by the tetratetracontane layer after annealing treatment. The device with encapsulation layer showed lower hysteresis, improved stability, and better repeatability. The temperature response of RGO-FET is examined by measuring changing the temperature, the device exhibited the high sensitivity and repeatability even with the temperature interval of 1 K. We also demonstrated that our devices have capability of IR sensing.

• Applied Microscopy
• /
• v.43 no.4
• /
• pp.173-176
• /
• 2013

The oxidation behavior of the crystallized $Al_{87}Ni_3Y_{10}$ alloy has been investigated with an aim to compare with that of the amorphous $Al_{87}Ni_3Y_{10}$ alloy. The oxidation at 873 K occurs as follows: (1) growth of an amorphous aluminum-yttrium oxide layer (~10 nm) after heating up to 873 K; and (2) formation of $YAlO_3$ crystalline oxide (~220 nm) after annealing for 30 hours at 873 K. Such an overall oxidation step indicates that the oxidation behavior in the crystallized $Al_{87}Ni_3Y_{10}$ alloy occurs in the same way as in the amorphous $Al_{87}Ni_3Y_{10}$ alloy. The simultaneous presence of aluminum and yttrium in the oxide layer significantly enhances the thermal stability of the amorphous structure in the oxide phase. Since the structure of aluminum-yttrium oxide is dense due to the large difference in ionic radius between aluminum and yttrium ions, the diffusion of oxygen ion through the amorphous oxide layer is limited thus stabilizing the amorphous structure of the oxide phase.

• Journal of Magnetics
• /
• v.1 no.1
• /
• pp.46-50
• /
• 1996

Highly oriented ${BaFe_{12}{O_{19}$ films were obtained by a KrF excimer laser ablation technique using (110)$(012){Al_2}{O_3}$(001)$(012){Al_2}{O_3}$ and $(012){Al_2}{O_3}$ substrates, respectively.The degree of alignment of more than 95% were achieved for (100) on (110)$(012){Al_2}{O_3}$ and (001)$(001){Al_2}{O_3}$ planes, and heteroepitaxial films of (114) on (012)$(012){Al_2}{O_3}$were possible to be grown with a lasing energy density of 6.67 J/$cm^2$ at an oxygen partial pressure ${PO_2}$ of 900 mTorr. The best magnetic properties were obtained from the as-deposited films at the substrate temperature of $700^{\circ}C$, and post annealing treatment was not needed to enhance the magnetic properties. Experimentally saturated magnetization ($4_pi M_S$) of 3600~3800 Gauss and coercivities $(H_c)$ of 3050~3080 Oe, which approach 85% of those of Ba-ferrite bulk composed of single domain particles, were obtained in this study.

• Korean Journal of Materials Research
• /
• v.28 no.2
• /
• pp.124-128
• /
• 2018

N-type porous silicon (PS) layers and thermally oxidized PS layers have been characterized by various measuring techniques such as photoluminescence (PL), Raman spectroscopy, IR, HRSEM and transmittance measurements. The top surface of PS layer shows a stronger photoluminescence peak than its bottom part, and this is ascribed to the difference in number of fine silicon particles of 2~3 nm in diameter. Observed characteristics of PL spectra are explained in terms of microstructures in the n-type PS layers. Common features for both p-type and n-type PS layers are as follows: the parts which can emit visible photoluminescence are not amorphous, but crystalline, and such parts are composed of nanocrystallites of several nm's whose orientations are slightly different from Si substrate, and such fine silicon particles absorb much hydrogen atoms near the surfaces. Light emission is strongly dependent on such fine silicon particles. Photoluminescence is due to charge carrier confinement in such three dimensional structure (sponge-like structure). Characteristics of visible light emission from n-type PS can be explained in terms of modification of band structure accompanied by bandgap widening and localized levels in bandstructure. It is also shown that hydrogen and oxygen atoms existing on residual silicon parts play an important role on emission stability.

• Korean Journal of Crystallography
• /
• v.1 no.1
• /
• pp.29-34
• /
• 1990

Single crystals of the peritectic compound MgTiO3 up to 8 m diameter and 100mm long along the [1010] axis. were yon by the travelling solvent floating zone technique using a halogen lamp image furnace. The grown single crystal. which shows a solid solution range at high temperature, exsolves TiO2 component if it is annealed very slowly to room termperature. Grown boules were black but become translucent with pinkish brown color after tempering at 1100 t for 8-10 hours in oxygen atmosphere and showed distint chatoyancy along the (0001) plane. The grown crystal can be used as a new modified cat's eye gemstone. The optimum conditions were as follows ;Sintering temperature of the charge rod, 1300℃ the growth rate, 2-2.5mmh and the composition of the charge rod in molar ratio. MgO : TiO2 : 1:1.05.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.1
• /
• pp.41-46
• /
• 2009

The low dielectric SiOCH films were deposited on p-type Si(100) substrates through the dissociation of BTMSM $(((CH_3)_3Si)_2CH_2)$ precursors with oxygen gas by using PECVD method. BTMSM precursor was introduced with the flow rates from 42 to 60 sccm by 2 sccm step into reaction chamber but with the constant flow rate of 60 sccm $O_2$. SiOCH thin films were annealed at $450^{\circ}C$ for 30 minutes. The electrical property of SiOCH thin films was studied by MIS, Al/SiOCH/p-Si(100), structure. Annealed samples showed large reduction of the maximum capacitance yielding low dielectric constant owing to reductions of surface charge density. After exposure at room temperature and atmospheric pressure, dielectric constant of SiOCH films was totally increased. However, annealed SiOCH thin films were more stable than as-deposited SiOCH thin films for natural oxidation.