• Journal of Power Electronics
• /
• v.4 no.2
• /
• pp.87-95
• /
• 2004

A new fast-response high-current clamp DC-DC converter circuit design is presented that will meet the requirements and features of the new generation of microprocessors and digital systems. The clamp in the proposed converter amplifies the current in case of severe load changes and is able to produce high slew rate of output current and capability to keep constant the output voltage. This proposed high-current clamp technique is theoretically loss less, low cost and easy to implement with simple control scheme. This is modified from a basic buck topology by replacing the output inductor with two magnetically coupled inductors. Inductors are difference in inductance, one has large inductance and other has small inductance. The inductor with small inductance will take over the output inductor during fast load transient. It speedup the output current slew rate and reduce the output voltage drop in the case of heavy burden load changes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.8
• /
• pp.505-509
• /
• 2014

In this research, the structural, physical and electrical characteristics of Ni-Fe core chosen to minimize the errors of the Hall current sensors were investigated and Hall current sensor using Ni-Fe core was fabricated. In the result, the fabricated Ni-Fe sample exhibited the maximum hardness about 29.5 GPa and the low friction coefficient about 0.35, and electrical resistivity over $90mOhm{\cdot}cm$. And also Hall current sensor using the fabricated Ni-Fe core showed linear current-voltage properties for DC current at $25^{\circ}C$ temperature.

• Resources Recycling
• /
• v.14 no.1
• /
• pp.55-63
• /
• 2005

This study investigated the electrochemical recovery of palladium in a HCl solution that is used for palladium leaching. The high acidity of HCl solution and the low concentration of Pd ions increased the cathodic overpotential and reduced the limiting current density. Lowering the current density produced dense deposits; however, they were under high tensile stress. Raising the temperature affected both the densification and the stress, which enabled the attainment of dense Pd deposits under low stress. Lowering the current density and raising the temperature up to 70$^{\circ}C$ was recommended for the recovery of palladium as sound bulk Pd deposits. Current efficiency was over 85% at the initial stage of recovery may decrease the current efficiency, since a low Pd ion concentration results in a low limiting current density.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.501-504
• /
• 1999

The polymer insulators which are installed on outdoor have a great advantage than porcelain and 71ass, due to suppression of leakage current, light weight, low cost, etc. It needs variable evaluation methods for application of these insulators on service. The analysis of measuring leakage current is useful for ageing diagnosis because of monitoring in real-time. In this paper, we look over the recovery of hydrophobicity of silicone rubber in mini salt-fog chamber with leakage current monitoring. also, we understand the relation of between hydrophobicity and leakage current and discuss on method of leakage current monitoring.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.491-494
• /
• 2000

Conductive Langmuir-Blodgett(LB) films have recently attracted much interest from the viewpoint of ultrathin film conductors at the molecular level. The result shows that the Maxwell-displacement-current(MDC) measuring technique is useful in the detection of phase-transition over the entire range of molecule areas. At the liquid-solid phase transition, a striking feature in the present current measurement was observed; the I-A isotherm for a DPPC monolayer has sharp bend. Dynamic behavior of monolayers in the presence of an external field was also investigated using the current-measuring technique. Dynamic behavier of DPPC monolayer was measured by displacement current when the molecules are stimulated by pressure velocity. As result, it is known that current is generated of higher current pe마 as compression velocity become faster. Also, in order to clarify the reorganization of the lipid monolayers, it is instructive to plot the relationship between I and 1/$A^2$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.542-548
• /
• 2001

A robust, accurate, broad-band, alternating current sensor using fiber-optics is being developed as a part of optical over current protection relay system. The sensor uses the Faraday effect in optical fiber and polarimetric measurements tc sense electrical current. The current sensing coil consists of a length of twisted optical fiber and Faraday rotator mirror to suppress the linear birefringence effect. Due to its single-ended closed path structure, it can not only be easily installed to the target with great isolation from other fields in the vicinity, but the sensitivity can be increased by using multiple turns. This paper reports on the theoretical backgrounds of the sensor design and the preliminary experimental results.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.309-312
• /
• 2003

In this study, the electrical characteristic of Symmetric high voltage MOSFET (SHVMOSFET) for display driver IC were investigated. Measurement data are taken over range of temperature (300K-400K) and various extended drain length. In high temperature condition(>400K), drain current decreased over 20％, and specific on-resistance increased over 30％ in comparison with room temperature.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.1
• /
• pp.30-34
• /
• 1997

An improved clock-feedthrough compensation scheme for switche dcurrent system is proposed. Both the signal dependent and the constant clock-feedthrough terms are cancelled by using both NMOS and PMOS current samplers and by adopting a source replication technique. The proposed current memory cell was fabricated with 0.6$\mu$m CMOS process. Both experimental and theoretical results on clock-feedthrough error reveal substantial reduction over the existing compensation schemes.

• 전기의세계
• /
• v.30 no.1
• /
• pp.41-46
• /
• 1981

In the current source inverters (CSI), which are widely used recently in many applications, in order to reduce the harmonic contents in the output line current, twelve-step waveform is synthesized usually by a phase-shifted addition of the output currents of two single CSI's. In this paper a new method of synthesis of the 12-step current waveform is suggested which employes a main and a new auxiliary inverters having lower capacity, and thus is economically advantageous over the conventional scheme. DC-side commutation and energy rebond circuit as described in Part I are also employed in this proposed twelve-step CIS for effective commutation and high reliability. Experimental results are also given in oscillgrams.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.12
• /
• pp.1619-1625
• /
• 2018

Portable electronic devices secondary batteries can cause fire and explosion due to micro-current change in addition to the situation of short-circuit inrush current, safety can not be secured with a general operation limited current fuse. Therefore, in secondary battery, it is necessary for the protector to satisfy both the limit current type operation in the open-short-circuit inrush current and the current detection operation characteristic in the micro current change situation and for this operation, a fuse for the current detection type secondary battery protection circuit can be applied. The purpose of this study is to design a protection device that operates stably in the hazardous situation of small capacity secondary battery for portable electronic devices through the design of low melting fuse elements alloy of sensing type fuse and secures stability in abnormal current state. As a result of the experiment, I-T and V-T operation characteristics are satisfied in a the design of the alloy of the current sensing type self-contained low melting point fuse and the resistance of the heating resistor. It is confirmed that it can prevent accidents of short circuit over-current and micro current change of secondary battery.