• 전력전자학회논문지
• /
• 제6권1호
• /
• pp.34-42
• /
• 2001

전지는 화학에너지를 기계적인 처리과정 없이 전기에너지로 직접 전환하는 장치이다. 부하전압과 부하전류의 용량에 따라 단위전지를 직.병렬 연결하여 사용하게 되며, 전지의 병렬운전은 단독운전 보다 전압강하를 더 천천히 발생시키므로 전압강하에 민감한 전력변환장치들의 효율에 밀접한 관계를 가지고 있다. 병렬운전의 필요성과 장점 때문에 대부분의 축전지를 사용하는 시스템은 병렬운전을 하고 있고, 반면에 선.구 축전지 사이에서 순환 전류가 흐르고, 자가방전이 일어나는 단점 또한 가지고 있다. 신 축전지에서 충.방전 전류가 과다하게 흐르는 불평형 현상과 이로 인해 축전지의 수명단축을 일으키게된다. 본 논문에서는 마이크로 프로세서를 사용하여 선.구 축전지 사이의 볼평형 전류를 검출하고 외부저항을 첨가시켜 내부저항의 차이에 대한 감소효과를 얻어 불평형 전류를 보상하였다. 이를 실험을 통해 구현하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.9-13
• /
• 2004

This paper proposes a modified current differential relay for Y-$\Delta$ transformer protection. The relay uses the same restraining current as a conventional relay, but the differential current is modified to compensate for the effects of the exciting current. A method to estimate the circulating component of the delta winding current is proposed. To cope with the remanent flux, before saturation, the core-loss current is calculated and used to modify the measured differential current. When the core then enters saturation, the initial value of the flux is obtained by inserting the modified differential current at the start of saturation into the magnetization cure. Thereafter, the core flux is then derived and used in conjunction with the magnetization curve to calculate the magnetizing current. A modified differential current is then derived that compensates for the core-loss and magnetizing currents. The performance of the proposed differential relay was compared against a conventional differential relay. Test results indicate that the modified relay remained stable during severe magnetic inrush and over-excitation because the exciting current was successfully compensated. The relay correctly discriminates magnetic inrush and over-excitation from an internal fault and is not affected by the level of remanent flux.

• 마이크로전자및패키징학회지
• /
• 제23권4호
• /
• pp.93-99
• /
• 2016

본 논문에서는 AgNW 필름의 기계적 전기적 신뢰성을 연구하였다. 특히 전류가 흐르는 상태에서 굽힘 변형이 발생하였을 때의 AgNW 필름의 내구성 및 신뢰성을 연구하였다. AgNW 필름의 전압 및 전류 시험을 수행하여, AgNW에서 발생하는 발열과 전류 밀도의 변화를 관찰함으로써 AgNW의 전기적 내구성을 평가하였다. AgNW는 곡률반경 2 mm까지 굽힐 수 있었으며, 200,000회의 굽힘 반복시험에도 높은 신뢰성 및 유연성을 보여주었다. 또한 over-coating 막은 AgNW 필름의 내구성을 향상시키는 효과가 있음을 확인하였다. Over-coating이 없는 AgNW 필름의 경우, AgNW 표면에서 국부적인 발열을 보인 반면에 over-coating이 된 AgNW 필름의 경우 균일하게 발열되어 over-coating막이 AgNW 필름의 내구성을 향상시킴을 알 수 있었다. 전류를 인가한 상태에서의 굽힘 시험을 수행한 결과 굽힘 반복시험에서는 전류밀도가 지속적으로 감소하여 시험 후, 52.4%의 전류밀도 감소를 보였다. 전류가 인가된 상태에서 AgNW의 굽힘 변형이 지속되면 AgNW들의 인장, 굽힘 및 sliding 등의 기계적인 변형에 의하여 AgNW network 구조의 변형이 발생하거나, 혹은 개별 AgNW의 접촉 접합부들이 떨어지면서 접촉저항이 증가하여 주울 열에 의하여 파괴가 발생한다. 또한 over-coating막의 적용은 AgNW 필름의 전기적 신뢰성을 향상시킬 수 있음을 알 수 있었다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.365-367
• /
• 2002

A serious problem in using YBCO films for fault current limiter is inhomogeneities caused by imperpect manufacturing. So simultaneous quenches are a difficult problem which elements for current limiting are connected in series for increasing voltage ratings. We investigated extended electric field - current characteristics for current limiting element of YBCO film when 0-130mT magnetic field is applied. And quench characteristics were investigated in over all element and between elements of YBCO films. From the experiments, it was shown that applied magnetic fields using solenoid coil induced uniform quench distribution for over all stripes and simultaneous quench in all elements for current limiting of YBCO film was realized.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전력기술부문
• /
• pp.363-365
• /
• 2006

This paper proposes an estimation method for a circulating current of a Y-${\Delta}$ Transformer. The delta winding current can be decomposed into the two components i.e. a non-circulating component and a circulating component. The former can be estimated using the line currents. However, the latter can not be estimated directly using the line currents. A first order differential equation for the circulating current is derived by applying the Kirchhoff's voltage law on the loop of the delta side. The circulating current can be estimated by the solving the differential equation. The performance of the proposed algorithm is investigated under various conditions including magnetic inrush and over-excitation. The algorithm can estimate the circulating current very accurately even under magnetic inrush and over-excitation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.210-213
• /
• 1999

A battery is the device that transforms the chemical energy into the direct-current electrical energy directly without a mechanical process. Unit cells are connected in series to obtain the necessary voltage, while being connected in parallel to organize capacity for load current and to decrease the internal resistance for corresponding the sudden shift of the load current. The circular-current, however, could be occurred when the system is driven in parallel. As a result, the new batteries are heated by over-change and discharge, and the over charge current makes to increase the rust of the positive grid and consequently the shortened life of the new batteris would be shown. In this paper, the internal resistance of charge and discharge will be balanced, through inserting the resistance into the system by way of calculation of the changed amount of internal resistance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.398-401
• /
• 2002

When the current flows over the allowable current due to the overload, it causes electric disaster such as an electrical fire and an electric shock by short current or leakage of electricity because the covering is deteriorated according to the heating action. In this paper, for the wire(IV 1.6mm) used as interior wiring, we analyzed a variation of the surroundings temperature, the form and the structure of a covering, and the crystal structure of a conductor. In the result of this experiment, the surroundings temperature at the allowable current of 300% rose to about 47$^{\circ}C$, and it rose up to the maximum allowable temperature of the wire at 400%. Consequently, it was broken within one minute at 500%. In the analysis of a metallograph, the conductor broken by the over current showed the dendrite. These analyses result will be applied to judging the electrical fire.

• 한국전기전자재료학회논문지
• /
• 제33권3호
• /
• pp.201-207
• /
• 2020

With the expansion in the use of DC power systems and increased need for system maintenance, the development of measurement devices for maintenance requires high stability. Of the different kinds of DC current measurement devices, the single-shot measurement device causes the input signal of the current measuring unit to initially generate a high inrush current. The high inrush current flows into the signal processor of the meter, shortening the life of the internal fuses and causing failure. Therefore, in this study, the I²t value for increasing the durability of the fuse is designed using the available wire diameter. Operating characteristics for 210~400% over-current of the rated current, which is relatively low over-current, are realized by the plating of low melting tin metal. As a result, a method of designing a fuse element for a DC power supply, which improves the safety of the DC current measurement device by blocking the failure caused by the inrush current, is presented.

• 전기학회논문지P
• /
• 제59권4호
• /
• pp.473-476
• /
• 2010

In this paper, we analyzed the short circuit current of a low voltage direct current distribution system. For the analysis, we performed the modeling of the low voltage direct current distribution system with a 6-pulse three-phase thyristor rectifier using the PSCAD/EMTDC, surveyed impedance of sources, transformers and distribution lines to run a simulation. A result of the simulation is that short circuit currents of the direct current distribution system with the rectifier decreased due to a thyristor-ON-resistance(Ron). But in case of the low thyristor-ON resistance, output fault current of the rectifier increased over three-phase short circuit current of an AC power system without a rectifier by regular ratio of the rectifier. Because the output fault current of the rectifier can increase over interrupting the capacity of circuit breakers, studying short circuit currents of a low voltage direct current distribution system with a rectifier is necessary for introducing the direct current distribution systems.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.365-366
• /
• 2009

This study researched into the manufacture of current-limit module of using YBCO coated conductor. Regarding over-current of exceeding the critical current, the quench characteristics were researched according to the stabilizing layer through tendency in resistance, which is generated in conductor, by applying over-current to YBCO coated conductors, which have stabilizing layer. YBCO coated conductors, which were used in experiment, include one kind such as the conductor, which used stainless as the stabilizing layer. The critical current is 70 A. And, the critical temperature is with 90 K. First of all, the quench generation was researched under over-current of exceeding the critical current by using this YBCO coated conductors. The tendency of a rise in the detected voltage according to the applied current was measured. And, the tendency of a rise in resistance through voltage-current curve was measured. As a result, the point of time in thermal quench of conductor, which has stainless as the stabilizing layer, could be confirmed to be fast.