• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.217-222
• /
• 2010

Paved roads are suffered from the permanent plastic deformation in hot summer and cracks in cold winter, which are detrimental to safe driving. This leads to necessity of modification of asphalt to resist those deformation. In this study, two kinds of modifiers were examined; organic polymers and a photoinitiator which is activated by ultraviolet lay. The mechanical and rheololgical properties of modified asphalts were examined using UTM and rheometer. Results showed that the properties were varied depending on the types of polymer and irradiation time. UV irradiation increased the tensile strength and storage modulus of thermoplastic polymer-modified asphalt, however UV was not effective on thermoset polymer. According to long term ultraviolet curing test, properties of the polymer/photoinitiator-modified asphalt did not decrease, but rather increase for 20 years. This indicates that the useful life of the asphalt could be extended by addition of photoinitiator.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1861-1866
• /
• 2012

The new semiconducting copolymers with 4,4-dialkyl-$4H$-cyclopenta[2,1-$b$:3,4-$b^{\prime}$]dithiophene and 2,2-dimethyl-$2H$-benzimidazole units were synthesized. The fused aromatic rings, such as cyclopentadithiophene (CPDT) unit, can make the polymer backbone more rigid and coplanar, which induces long conjugation length, narrow band gap, and strong intermolecular ${\pi}-{\pi}$ interaction. The stacking ability was controlled through attaching of linear or branched alkyl side chains. The spectra of PEHCPDTMBI and PHCPDTMBI in the solid films show absorption bands with maximum peaks at 401, 759 and 407, 768 nm, and the absorption onsets at 925 and 954 nm, corresponding to band gaps of 1.34 and 1.30 eV, respectively. The devices comprising PHCPDTMBI with $TiO_X$ showed a $V_{OC}$ of 0.39 V, a $J_{SC}$ of 1.14 $mA/cm^2$, and a $FF$ of 0.34, giving a power conversion efficiency of 0.15%. The PHCPDTMBI with linear alkyl chain on CPDT shows good solubility in organic solvent with higher PCE value than that of PEHCPDTMBI.

• Membrane Journal
• /
• v.8 no.4
• /
• pp.228-234
• /
• 1998

Among various water contaminents, organic compounds like phenol are difficult to be removed or destroyed by conventional methods under the unusual discharge conditions. The separation of phenol from aqueous solution has been carried out by several methods recently: absorption by an activated carbon, solvent extraction and liquid membrane technology. The liquid membrane based on water-oil emulsification has been tested as an alternative technology of the conventional technology. In this work, tri-n-butyl phosphate(TBP) and liquid polymers were examined as a liquid membrane in the supported liquid membrane(SLM). The feed concentration of phenol was varied and various types of liquid membranes were used to examine their effects on separation of phenol. It was found that TBP, polypropylene glycol 4000(PPG 4000) and polybutytene glycol 500(PBG 500) were proper carriers because mass transfer rates through them were much higher than or similar to that through methyl isobutyl ketone(MIBK) which was used as a conventional solvent in a solvent extraction process.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.11 no.6
• /
• pp.489-495
• /
• 2006

In recent years, there has been an interest to use Moringa oleifera as the natural coagulant due to cost, associated health and environmental concerns of synthetic organic polymers and inorganic chemicals. However, it is known that M. oleifera as the natural coagulant is highly biodegradable and has a very short shelf life. This research was carried out to investigate the effects of storage temperature, packaging methods, and freeze-drying on the preservation of M. oleifera seeds powders. Non freeze-dried M. oleifera was prepared into different packaging namely open container, closed container and vacuum packing, whilst, freeze-dried M. oleifera was stored in closed container and vacuum packing. Each of the packaging was stored at room temperature ($30\;to\;32^{\circ}C$) and refrigerator ($4^{\circ}C$). The turbidity removal efficiencies of stored M. oleifera were examined using jar test at monthly interval for 12 months. The results indicated that non freeze-dried M. oleifera kept in the refrigerator ($4^{\circ}C$) would preserve its coagulation efficiency. In addition, closed container and vacuum packing were found to be more appropriate for the preservation of non freeze-dried M. oleifera, compared to open container. Freeze-dried M. oleifera retained its high coagulation efficiency regardless the storage temperature and packaging method for up to 11 months. Besides, higher increment in zeta potential values for water coagulated with freeze-dried M. oleifera indicated the higher frequency of charge neutralization and better coagulation efficiency of freeze-dried M. oleifera, compared to non freeze-dried seeds. As a coagulant, M. oleifera did not affect the pH of the water after treatment.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.573-579
• /
• 2008

PBA/PS core-shell polymer nanoparticles were synthesized by two stage emulsion polymerization and hybridized with silica nanoparticle by simple mixing in emulsion state and following precipitation into water/methanol mixture dissolving $Na_2CO_3$. The stress-strain curve revealed that the elastic modulus was increased with increasing molecular weight of polymer and silica weight fraction but decreased with increasing size of core-shell nanoparticle. Especially, there was a rapid increase of elastic modulus with silica blending. As a result, 6 times higher elastic modulus was observed in PBA/PS core-shell baroplastic sample processed at 25$^\circ$C under 13.8 MPa for 5 min by blending with 13.0 wt% of silica nanoparticle.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.297.2-297.2
• /
• 2013

Scavenging electricity from wasteful energy resources is currently an important issue and piezoelectric nanogenerators (NGs) based on zinc oxide (ZnO) are promising energy harvesters that can be adapted to various portable, wearable, self-powered electronic devices. Although ZnO has several advantages for NGs, the piezoelectric semiconductor material ZnO generate an intrinsic piezoelectric potential of a few volts as a result of its mechanical deformation. As grown, ZnO is usually n-type, a property that was historically ascribed to native defects. Oxygen vacancies (Vo) that work as donors exist in ZnO thin film and usually screen some parts of the piezoelectric potential. Consequently, the ZnO NGs' piezoelectric power cannot reach to its theoretical value, and thus decreasing the effect from Vo is essential. In the present study, c-axis oriented insulator-like sputtered ZnO thin films were grown in various temperatures to fabricate an optimized nanogenerator (NGs). The purity and crystalinity of ZnO were investigated with photoluminescence (PL). Moreover, by introducing a p-type polymer usually used in organic solar cell, it was discussed how piezoelectric passivation effect works in ZnO thin films having different types of defects. Prepared ZnO thin films have both Zn vacancies (accepter like) and oxygen vacancies (donor like). It generates output voltage 20 time lager than n-type dominant semiconducting ZnO thin film without p-type polymer conjugating. The enhancement is due to the internal accepter like point defects, zinc vacancies (VZn). When the more VZn concentration increases, the more chances to prevent piezoelectric potential screening effects are occurred, consequently, the output voltage is enhanced. Moreover, by passivating remained effective oxygen vacancies by p-type polymers, we demonstrated further power enhancement.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.28 no.3
• /
• pp.241-256
• /
• 2018

Objectives: This study aimed to review the characteristics of three-dimensional printing technology focusing on printing types, materials, and health hazards. We discussed the methodologies for exposure assessment on hazardous substances emitted from 3D printing through article reviews. Methods: Previous researches on 3D printing technology and exposure assessment were collected through a literature review of public reports and research articles reported up to July 2018. We mainly focused on introducing the technologies, printing materials, hazardous emissions during 3D printing, and the methodologies for evaluation. Results: 3D printing technologies can be categorized by laminating type. Fused deposition modeling(FDM) is the most widely used, and most studies have conducted exposure assessment using this type. The printing materials involved were diverse, including plastic polymer, metal, resin, and more. In the FDM types, the most commonly used material was polymers, such as acrylonitrile-butadiene-styrene(ABS) and polylactic acids(PLA). These materials are operated under high-temperature conditions, so high levels of ultrafine particles(mainly nanoparticle size) and chemical compounds such as organic compounds, aldehydes, and toxic gases were identified as being emitted during 3D printing. Conclusions: Personal desktop 3D printers are widely used and expected to be constantly distributed in the future. In particular, hazardous emissions, including nano sized particles and various thermal byproducts, can be released under operation at high temperatures, so it is important to identify the health effects by emissions from 3D printing. Furthermore, appropriate control strategies should be also considered for 3D printing technology.

• Journal of Chitin and Chitosan
• /
• v.23 no.4
• /
• pp.256-261
• /
• 2018

Recently, the number of cardiovascular disease-related deaths worldwide has increased. Therefore, the importance of percutaneous cardiovascular intervention and drug-eluting stents (DES) has been highlighted. Despite the great clinical success of DES, the re-endothelialization at the site of stent implantation is retarded owing to the anti-proliferative effect from the coated drug, resulting in late thrombosis or very late restenosis. In order to solve this problem, studies have been actively carried out to excavate new drugs that promote rapid re-endothelialization. In this study, we introduced hydrophilic drug, tauroursodeoxycholate (TUDCA), that improves the proliferation of endothelial progenitor cells and promotes apoptosis of vascular smooth muscle cells. In addition, we utilized shellac, which is a natural resin from lac bug to coat TUDCA on the surface of the metal. When using conventional coating method including biodegradable polymers and organic solvents, phase separation between polymer and drug occurred in the coating layer that caused incomplete incorporation of drug into the polymer layer. However, when using shellac as a coating polymer, no phase separation was observed and drug was fully covered with the polymer matrix. In addition, by adjusting the composition of coating solution and modifying the hydrophilicity of the metal surface using oxygen plasma, the surface roughness decreased due to the increased affinity between coating solution and metal surface. This result provides a method of depositing a hydrophilic drug layer on the stent.

• Advances in nano research
• /
• v.10 no.3
• /
• pp.253-261
• /
• 2021

Polydimethylsiloxane (PDMS) is one of the most widely adopted silicon-based organic polymeric elastomers. Elastomeric nanostructures are normally required to accomplish an explicit mechanical role and correspondingly their mechanical properties are crucial to affect device and material performance. Despite its wide application, the mechanical properties of PDMS are yet fully understood. In particular, the time dependent mechanical response of PDMS has not been fully elucidated. Here, utilizing state-of-the-art PeakForce Quantitative Nanomechanical Mapping (PFQNM) together with Force Volume (FV) and Fast Force Volume (FFV), the elastic moduli of PDMS samples were assessed in a time-dependent fashion. Specifically, the acquisition frequency was discretely changed four orders of magnitude from 0.1 Hz up to 2 kHz. Careful calibrations were done. Force data were fitted with a linearized DMT contact mechanics model considering surface adhesion force. Increased Young's modulus was discovered with increasing acquisition frequency. It was measured 878 ± 274 kPa at 0.1 Hz and increased to 4586 ± 758 kPa at 2 kHz. The robust local probing of mechanical measurement as well as unprecedented high-resolution topography imaging open new avenues for quantitative nanomechanical mapping of soft polymers, and can be extended to soft biological systems.

• Proceedings of the Microbiological Society of Korea Conference
• /
• 2001.11a
• /
• pp.39-45
• /
• 2001

Extremophiles are unique microorganisms that are adapted to survive in ecological niches such as high or low temperatures, extremes of pH, high salt concentrations and high pressure. These unusual microorganisms have unique biochemical features which can be exploited for use in the biotechnological industries. Due to the high biodiversity of extremophilic archaea and bacteria and their existence in various biotopes a variety of biocatalysts with different physicochemical properties have been discovered. The extreme molecular stability of their enzymes, membranes and the synthesis of unique organic compounds and polymers make extremophiles interesting candidates for basic and applied research. Some of the enzymes from extremophiles, especially hyperthermophilic marine microorganisms (growth above $85^{\circ}C$), have already been purified in our laboratory. These include the enzyme systems from Pyrococcus, Pyrodictium, Thermococcus and Thermotoga sp. that are involved in polysacharide modification and protein bioconversion. Only recently, the genome of the thermoalkaliphilic strain. Anaerobranca gottschalkii has been completely sequenced providing a unique resource of novel biocatalysts that are active at high temperature and pH. The gene encoding the branching enzyme from this organism was cloned and expressed in a mesophilic host and finally characterized. A novel glucoamylase was purified from an aerobic archaeon which shows optimal activity at $90^{\circ}C$ and pH 2.0. This thermoacidophilic archaeon Picrophilus oshimae grows optimally at pH 0.7 and $60^{\circ}C$. Furthermore, we were able to detect thermoactive proteases from two anaerobic isolates which are able to hydrolyze feather keratin completely at $80^{\circ}C$ forming amino acids and peptides. In addition, new marine psychrophilic isolates will be presented that are able to secrete enzymes such as lipases, proteases and amylases possessing high activity below the freezing point of water.