• Mass Spectrometry Letters
• /
• v.6 no.3
• /
• pp.59-64
• /
• 2015

Quadrupole ion trap mass analyzer with a simplified geometry, namely, the cylindrical ion trap (CIT), has been shown to be well-suited using in miniature mass spectrometry and even in mass spectrometer arrays. Computation of stability regions is of particular importance in designing and assembling an ion trap. However, solving CIT equations are rather more difficult and complex than QIT equations, so, analytical and matrix methods have been widely used to calculate the stability regions. In this article we present the results of numerical simulations of the physical properties and the fractional mass resolutions m/Δm of the confined ions in the first stability region was analyzed by the fifth order Runge-Kutta method (RKM5) at the optimum radius size for both ion traps. Because of similarity the both results, having determining the optimum radius, we can make much easier to design CIT. Also, the simulated results has been performed a high precision in the resolution of trapped ions at the optimum radius size.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.2
• /
• pp.170-177
• /
• 2019

In this paper, three theories for improving the stability of quadruped robot are presented. First, the Minimum-Jerk Trajectory is used to optimize the leg trajectory. Second, we compare the newly proposed sine wave and the conventional LSM in this paper based on the Jerk value. Third, we calculate the optimum stride of the sway through repetitive robot simulation using ADAMS-MATLAB cosimulation. Through the above process, the improvement of the robot walking is compared with the existing theory. First, the average gradient of the point where the leg trajectory changes rapidly was reduced from at least 1.2 to 2.9 by using the Minimum-Jerk targetory for the movement of the body and the end of the leg during the first walk, thereby increasing the walking stability. Second, the average Jerk was reduced by 0.019 on the Z-axis, 0.457 on the X-axis, and 0.02, 3D on the Y-axis by 0.479 using the Sin wave type sways presented in this paper, rather than the LSM(Longitude Stability Margin) method. Third, the length of the optimal stride for walking at least the Jerk value was derived from the above analysis, and the 20cm width length was the most stable.

• Journal of Educational Research in Mathematics
• /
• v.20 no.1
• /
• pp.85-102
• /
• 2010

Linear programming(LP) is useful for finding the best way in a given condition for some list of requirements represented as linear equations. This study analysed LP in mathematics contexts and LP in school mathematics contexts, considered learning process of LP from an epistemological point of view, and explored a hypothetical learning trajectory of LP. The differences between mathematics contexts and school mathematics contexts are whether they considered that the convex polytope $\Omega$ is feasible/infeasible or bounded/unbounded or not, and whether they prove the theorem that the optimum is always attained at a vertex of the polyhedronor not. And there is a possibility that students could not understand what is maximum and minimum of a linear function when the domain of the function is limited. By considering these three aspects, we constructed hypothetical learning trajectory consisted of 4 steps. The first step is to see a given linear expression as linear function, the second step is to partition a given domain by straight lines, the third step is to construct the conception of y-intercept by relating lines and the range of k, and the forth step is to identify whether there exists the optimum in a given domain or not.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.5
• /
• pp.616-624
• /
• 2019

In order to understand flying aircraft, satellite, missile, etc, a telemetry ground system is used to receive, record, and process the transmitted radio signal from vehicles. In some cases, a line-of-sight communication is not possible along to the trajectory of vehicles, and multipath fading result in a shade area of communication. A number of telemetry ground systems are installed to overcome this limitation, and acquire the transmitted signal seamlessly. The telemetry signals received by multiple independent ground systems have independent probability of errors since they experienced their own communication channels. In other words, we can exploit the independent error characteristics of received signals by processing them in a hybrid method. The optimum hybrid post-process method is proposed in this study, and applied to process telemetry signals acquired from flight tests.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.6
• /
• pp.126-134
• /
• 2001

Recently, high productivity and cost reduction becomes the most important target of industries due to the worldwide economic competition. One of these efforts is High Speed Machining(HSM), which reduces machining time with the increase of machining speed such as cutting speed and feedrate. It is very important, especially in case that the portion of machining time in production cost is high. This research suggests optimum cutting conditions to reduce cutting time with minimizing term error. For this study, a comprehensive model representing the texture of machining surface is developed, including rubbing phenomenon on the tip of ball end mill and expanded fibbing zone trajectory caused by tool deflection. Experiments show that the suggested set of feed and pick feed is optimum for maintaining the surface roughness identified by rubbing and low cutting speed in minimum.

• Advances in Energy Research
• /
• v.3 no.1
• /
• pp.1-10
• /
• 2015

In the past sidetracking was the means to bypass a damaged zone or to correct the direction of a wellbore. Nowadays, this method is very common and useful in relocating the bottom of a wellbore in a more productive zone and consequently enhancing the production of a reservoir by saving a significant amount of time and money. In this paper, the stability of the bend area is assessed considering varied conditions of stress regime and sidetrack orientation. In general, the stress regime and the orientation of the principal stresses have negligible effect on the stability of the sidetrack compared to sidetrack inclination. On the other hand, the sidetrack deviation angle from the vertical main well plays the major role in the stability of the bend area.

• 연구논문집
• /
• s.22
• /
• pp.75-83
• /
• 1992

The beating motion of a high speed shuttleless loom is driven by cams. Two cams become one system and their shaft laid across each other. Moreover, the shape of the cams is very complex and requires high precision for successful weft insertion and good interlacing with warp yarn. The iterative contact method is developed for use in design and analysis of the driving mechanism of a disk type cam with oscillating roller follower. The optimum design is performed by utilizing a CAD program, DISKCAM. The 8th order polynomial is selected to interpolate the desired shape trajectory of the cam, the optimal shape of the cams is defined based on the demension of the follower. The kinematic motion of the beating cam mechanism is investigated. The phase angle is determined to achive harmonious cam motions

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.936-941
• /
• 2014

Walking mechanisms are very important for legged robots to ensure their stable locomotion. In this research, Klann-linkage is suggested as a walking mechanism for a water-running robot and is optimized using level average analysis. The structure of the Klann-linkage is introduced first and design variables for the Klann-linkage are identified considering the kinematic task of the walking mechanism. Next, the design problem is formulated as a path generation optimization problem. Specifically, the desired path for the foot-pad is defined and the objective function is defined as the structural error between the desired and the generated paths. A process for solving the optimization problem is suggested utilizing the sensitivity analysis of the design variables. As a result, optimized lengths of Klann-linkage are obtained and the optimum trajectory is obtained. It is found that the optimized trajectory improves the cost function by about 62% from the initial one. It is expected that the results from this research can be used as a good example for designing legged robots.

• The Journal of the Korea Contents Association
• /
• v.6 no.1
• /
• pp.114-125
• /
• 2006

Since wireless Internet services and small mobile communication devices come into wide use as well as the use of GPS is rapidly growing, researches on moving object, whose location information shifts sequently in accordance with time interval, are being carried out actively. Especially, the researches on vehicle moving object are applied to Advanced traveler information system, vehicle tracking system, and distribution transport system. These systems are very useful in searching previous positions, predicted future positions, the optimum course, and the shortest course of a vehicle by managing historical data of the vehicle movement. In addition, vehicle historical data are used for distribution transport plan and vehicle allocation. Vehicle historical data are stored at regular intervals, which can have a pattern. For example, a vehicle going repeatedly around a specific section follows a route very similar to another. If historical data of the vehicle with a repeated route course are stored at regular intervals, many redundant data occur, which result in much waste of storage. Therefore this thesis suggest a vehicle historical data store scheme for vehicles with a repeated route course using similar trajectory which efficiently store vehicle historical data.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.68-77
• /
• 2018

In order to analyze the overall characteristics of the lunar orbiter, the Variable Coast method, which can be launched everyday, is applied to the 3.5 phasing loop transfer trajectory. The mission scenario for the entire process from launching to entering the lunar orbit is set up and performed simulation by selecting the launch pad and launch vehicle. In particular, the SEM(Satellite-Earth-Moon) angle defined in Earth-Moon rotating frame is an important constraint to comprehensively evaluate the 3.5 phasing loop transfer trajectory. The simulation using SEM angle is analyzed from various viewpoints such as launch epoch, coast duration, perigee altitude and ${\Delta}V$ not only trans-lunar trajectory but lunar orbit insertions and the optimum SEM angle is suggested in this study. It is expected that this results will be helpful to evaluate the characteristics of the 3.5 phasing loop transfer trajectory according to the launch vehicle selection by comparison with Fixed Coast analysis results in the future.