• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.302-307
• /
• 2003

Demand of the LCD-TV is remarkably increasing with development of the LCD technology in these days. Thus, this research has analyzed thermal problems such as heat transfer characteristics inside and outside the LCD-TV using numerical simulation and experiments. The simulated results have been compared with the experimental results using an infrared (IR) camera and T-type thermocouples. The optimal design of structure has been proposed to improve the thermal efficiency of radiation from the comparison.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.455-462
• /
• 2009

This paper presents design concepts of a reconfigurable mobile robot for both of indoor and outdoor applications. A linkage mechanism and wheel-in-motors give the proposed mobile robot various driving modes in maneuver and good adaptability to irregular surface. Since the mobile robot receives multiple sensor signals from odometers and an orientation sensor, states related to the position and the orientation of the mobile robot are optimally estimated by an extended Kalman filter. Simulations and experimental results show that the performance of dead reckoning on estimating the pose of a mobile robot can be improved remarkably by the optimal state observer.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.146-148
• /
• 2006

The aim of the paper is to design the PLS(Plasma Lighting System) driving inverter circuit with optimal efficiency. In general, it is known that the PLS driven by a pulse has a higher light-conversion efficiency. There are the Class-E type resonant inverter and the semi-bridge inverter as a circuit which can make a pulse with low duty ratio. In this paper, we analyze the losses of the above two circuits. To verify the loss analysis, the inverter circuit with 220V 380W input consumption is manufactured and tested. Throughout the experimental results, the high efficiency PLS system has confirmed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.252-255
• /
• 2003

The pulsed laser deposition process modeling is investigated using neural networks based on radial basis function networks and multi-layer perceptron. Two input factors are examined with respect to the PL intensity. In order to minimize the joint confidence region of fabrication process with varying the conditions, D-optimal experimental design technique is performed and photoluminescence intensity is characterized by neural networks. The statistical results were then used to verify the fitness of the nonlinear process model. Based on the results, this modeling methodology can be optimized process conditions for pulsed laser deposition process.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.1
• /
• pp.16-23
• /
• 2004

Permanent magnet-excited transverse flux linear motor(TFLM) is known to have more excellent ratio of force to weight than any other linear motors. But, thrust generated by phase current is non-linear with regard to current and relative position like switched reluctance motor. This makes current and speed controller design difficult. This paper presents a method on minimization of thrust ripple of permanent magnet-excited transverse flux linear motor. Using genetic algorithm(GA), optimal current waveform can be found under the constraint conditions such as current limit, minimum of ohmic loss and limited rate of change of current etc. The effectiveness is verified through computer simulation and experimental test results.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.84-92
• /
• 2005

This work presents the feasibility of shunt damping far vibration suppression of the rotating HDD disk-spindle system using piezoelectric bimorph. A target vibration mode which significantly restricts the recording density increment of the drive is determined through modal analysis and a piezoelectric bimorph is designed to suppress unwanted vibration. After deriving the two-dimensional generalized electromechanical coupling coefficient of the shunted drive, the shunt damping of the system is predicted by simulating the displacement transmissibility using the coefficient. In addition, optimal design process using sensitivity analysis is undertaken in order to improve the shunt damping of the system. The effectiveness of the proposed methodology is verified through experimental implementation by observing the vibration characteristics of the rotating disk-spindle system in frequency domain.

• Journal of Biomedical Engineering Research
• /
• v.17 no.2
• /
• pp.215-220
• /
• 1996

Impact force and strains induced by impact between the occluder and the struts have been measured with force sensor and strain gages. The maximum reaction force was about 25N, and the calculated impact force on the root of the struts amount about 9-17W. Impact force on the inlet strut is greater than that of the outlet strut, but the strain on the outlet strut is much higher than that of the inlet strut. These values might cause severe damage on the valve in the critical cases. The results of this study may be extended for the analysis of the endurance limit and optimal design of the struts and occluder.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.229-229
• /
• 2000

Conventional gain-tuning methods such as Ziegler-Nickels methods, have many disadvantages that optimal control ler gain should be tuned manually. In this paper, modified PID controllers which include self-tuning characteristics are proposed. Proposed controllers automatically tune the PID gains in on-1ine using neural networks. A new learning scheme was proposed for improving learning speed in neural networks and satisfying the real time condition. In this paper, using a nonlinear mapping capability of neural networks, we derive a tuning method of PID controller based on a Back propagation(BP)method of multilayered neural networks. Simulated and experimental results show that the proposed method can give the appropriate parameters of PID controller when it is implemented to DC Motor.

• 한국연소학회:학술대회논문집
• /
• 2006.04a
• /
• pp.172-180
• /
• 2006

A novel pyrolysis-melting incineration system of reduced scale (30 kg/hr) is and constructed in Korea Institute of Industrial Technology. The incineration process is composed of three parts: pyrolysis, gas combustion and ash melting processes. For each unit process, experimental and numerical approaches including reduced-scale cold/hot flow tests have been conducted to find optimal design and operating conditions. This paper presents major results of these approaches with brief descriptions on the pilot-scale incinerator (200 kg/hr) under construction and future research works.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.165-166
• /
• 1998

A multi-parameter neuro muscular electrical simulator (NMES) system was developed to be used to find the optimal parameter condition in obtaining maximum muscle power and minimal fatigue. Since the performance of NMES is mainly determined by the characteristic of its output-stage circuit, we implemented 3 different circuits and compared output characteristics of them. Three amplifier circuits are; 1) a resonant switching converter, 2) a linear amplifier with a transformer, and 3) a step-up DC/DC converter with a high-voltage linear amplifier. Experimental results showed that the step up DC/DC converter with a high-voltage linear amplifier has the best performance.