• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.443-450
• /
• 2014

This paper presents a 20-Gb/s optical receiver circuit fabricated with standard 65-nm CMOS technology. Our receiver circuits are designed with consideration for parasitic inductance and capacitance due to bonding wires connecting the photodetector and the circuit realized separately. Such parasitic inductance and capacitance usually disturb the high-speed performance but, with careful circuit design, we achieve optimized wide and flat response. The receiver circuit is composed of a transimpedance amplifier (TIA) with a DC-balancing buffer, a post amplifier (PA), and an output buffer. The TIA is designed in the shunt-feedback configuration with inductive peaking. The PA is composed of a 6-stage differential amplifier having interleaved active feedback. The receiver circuit is mounted on a FR4 PCB and wire-bonded to an equivalent circuit that emulates a photodetector. The measured transimpedance gain and 3-dB bandwidth of our optical receiver circuit is 84 $dB{\Omega}$ and 12 GHz, respectively. 20-Gb/s $2^{31}-1$ electrical pseudo-random bit sequence data are successfully received with the bit-error rate less than $10^{-12}$. The receiver circuit has chip area of $0.5mm{\times}0.44mm$ and it consumes excluding the output buffer 84 mW with 1.2-V supply voltage.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.136-139
• /
• 2003

A clock recovery circuit for a 40 Gb/s optical receiver has been designed and implemented. The clock recovery circuit consists of signal amplifiers, a nonlinear circuit with diodes, and a bandpass filter Before implementing the 40 Gb/s clock recovery circuit, a 10 Gb/s clock recovery circuit has been successfully implemented and tested. With the 40 Gb/s clock recovery circuit, when a 40 Gb/s NRZ signal of -10 dBm was applied to the input of the circuit, the 40 GHz clock was recovered with the -20 dBm output power after passing through the nonlinear circuit. The output signal from the nonlinear circuit passes through a narrow-band filter, and then amplified. The implemented clock recovery circuit is planned to be used for the input of a phase locked loop to further stabilize the recovered clock signal and to reduce the clock jitter.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2005년도 하계학술대회
• /
• pp.154-158
• /
• 2005

In this paper, we design optical receiver composed of CDR(clock and data recovery), SA(sense amp), TIA(transimpe dence amplifier), and decision circuit. The optical receiver can be classified to two main block, one is Deserializer composed of CDR and SA, another is PD receiver composed of preamplifier(샴), peak detector, etc. In this paper, we propose CDR using delayed data topology that could improve defects of existing CDR. The optical receiver that is proposed in this paper has the role of translation a 1.25 Gb/s optical signal to $10{\times}125 Mb/s$ array electric signals. This optical receiver is verified by simulator(hspice) using 0.35 um CMOS technology.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2002년도 제13회 정기총회 및 2002년도 동계학술발표회
• /
• pp.184-185
• /
• 2002

We discussed the main issues of 10GHz Receiver packaging. High frequency structure simulations and circuit simulations for TO-CANs led to a new design for 10GHz optical receiver module packaging. The simulation results were compared to the measured laboratory data. The proposed package has low cost and easy manufacture process far mass production. Using this package, we had a good optical to electrical conversion (OE) characteristic at a data rate of 10Gbps.

• Journal of the Optical Society of Korea
• /
• 제20권5호
• /
• pp.623-627
• /
• 2016

A power-adjustable fully-integrated CMOS optical receiver with multi-rate clock-and-data recovery circuit is presented in standard 65-nm CMOS technology. With supply voltage scaling, key features of the optical receiver such as bandwidth, power efficiency, and optical sensitivity can be automatically optimized according to the bit rates. The prototype receiver has −23.7 dBm to −15.4 dBm of optical sensitivity for 10⁻⁹ bit error rate with constant conversion gain around all target bit rates from 1.62Gbps to 8.1 Gbps. Power efficiency is less than 9.3 pJ/bit over all operating ranges.

• 한국전자파학회논문지
• /
• 제15권2호
• /
• pp.134-139
• /
• 2004

40 Gb/s 광 수신기용 클락 복원회로를 설계 및 제작하였다. 클락 복원회로는 전치 증폭기, 다이오드를 이용한 비선형 회로, 대역통과 필터, 클락 증폭기로 구성되어 있다. 40 Gb/s 클락 복원회로를 제작하기에 앞서 10 Gb/s 클락 복원회로를 제작, 측정하였다. 40 Gb/s 클락 복원회로에 -10 dBm의 40 Gb/s NRZ 신호를 입력하였을 때, 비선형 회로를 통과한 후에 40 GHz의 클락이 출력 전력 -20 dBm으로 복원되었다. 비선형 회로를 통과하여 복원된 클락은 협대역 필터를 통과하고, 증폭되게 된다. 제작된 클락 복원회로는 클락의 지터를 감소시키고, 더욱 안정화 시키기 위하여 위상 동기 회로의 입력으로 사용되게 된다.

• 대한전자공학회논문지SD
• /
• 제41권1호
• /
• pp.47-52
• /
• 2004

본 논문에서는 FTTH에 적용하기 적합한 넓은 입력 다이나믹 레인지와 낮은 비트 에러율을 갖는 CMOS 광수신기의 설계를 제안한다. 트랜스임피던스 전치증폭기의 PMOS 피드백 저항을 자신의 출력 신호의 크기에 따라 제어하여 100Mbps까지 60dB의 입력 다이나믹 레인지를 얻었다. 듀티 에러를 최소화시키기 위해 전류 거울 형태의 자동 바이어스 조절 회로를 설계하였다. 2-폴리, 3-메탈, 0.6um CMOS 공정 파라미터를 사용하여 회로 시뮬레이션을 수행하였다. 설계된 수신기는 5V의 전원을 사용할 때 100Mbps에서 130mW 이하의 전력 소비를 보였다.

• 전자공학회논문지A
• /
• 제33A권11호
• /
• pp.1-9
• /
• 1996

In the following paper, new architectural algorithm of clock and data recovery circuit is proposed for 622.08 Mbps optical communication receiver. New algorithm makes use of charge pump PLL using voltage controlled ring oscillator and extracts 8-channel 77.76 MHz clock signals, which are delayed by i/8 (i=1,2, ...8), to convert and recover 8-channel parallel data from 662.08 Mbps MRZ serial data. This circuit includes clock genration block to produce clock signals continuously even if input data doesn't exist. And synchronization of data and clock is doen by the method which compares 1/2 bit delayed onput data and decided dta by extracted clock signals. Thus, we can stabilize frequency and phase of clock signal even if input data is distorted or doesn't exist and simplify receiver architecture compared to traditional receiver's. Also it is possible ot realize clock extraction, data decision and conversion simulataneously. Verification of this algorithm is executed by DESIGN CENTER (version 6.1) using test models which are modelized by analog behavior modeling and digital circuit model, modified to process input frequency sufficiently, in SPICE.

• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.176-179
• /
• 1989

The optimization of the monolithic pin-FET receiver is discussed, with emphasis on the sensitivity and bandwidth. The amplifier circuit, bias resistance, total input capacitance, and transconductance of FET for the 2 Gbps transmission are calculated.

• ETRI Journal
• /
• 제35권1호
• /
• pp.1-6
• /
• 2013

In this paper, we present an implemented serial 40-Gb/s receiver optical subassembly (ROSA) module by employing a proposed TO-CAN package and flexible printed circuit board (FPCB). The TO-CAN package employs an L-shaped metal support to provide a straight line signal path between the TO-CAN package and the FPCB. In addition, the FPCB incorporates a signal line with an open stub to alleviate signal distortion owing to an impedance mismatch generated from the soldering pad attached to the main circuit board. The receiver sensitivity of the ROSA module measures below -9 dBm for 40 Gb/s at an extinction ratio of 7 dB and a bit error rate of $10^{-12}$.