• Membrane and Water Treatment
• /
• v.10 no.3
• /
• pp.201-206
• /
• 2019

In this study, we performed an electrowinning process for effective removal of metals (Cu and Ni) in solution and their recovery as solid forms. A complete removal of Cu and Ni (1,000 mg/L) was observed during four times recycling test, indicating that our electrowinning system can ensure the efficient metal removal with high stability and durability. In addition, we investigated effect of operation parameters (i.e., concentration of boric acid only for Ni, variation of pH, concentration of electrolyte ($H_2SO_4$), and cell voltage) on the efficiency of metal removal (Cu and Ni) during the electrowinning. The addition of boric acid significantly enhanced removal efficiency of Ni as the concentration of boric acid increased up to 10 g/L. Compared to negligible pH effect (pH 1, 2, and 4) on the Cu removal, we observed the increase in removal efficiency of Ni as the pH increased from 1 to 4. The electrolyte concentration did not significantly influence the removal of Cu and Ni in this study. We also obtained great removal rates of Cu and Ni at 2.5 V and 4.0 V, which were much faster than those at lower voltages. Finally, almost 99% of each Cu and Ni (1,000 mg/L) was selectively removed from the mixture of metals by adjusting pH and addition of boric acid after the completion of Cu removal. The findings in this study can provide a fundamental knowledge about effect of important parameters on the efficiency of metal recovery during the electrowinning.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.201-206
• /
• 2019

This study presents the design and experimental result of a GaN-based DC-DC converter with an integrated gate driver. The GaN device is attractive to power electronic applications due to its superior device performance. However, the switching loss of a GaN-based power converter is susceptible to the common source inductance, and converter efficiency is severely degraded with a large loop inductance. The objective of this study is to achieve high-efficiency power conversion and the highest power density using a multiphase integrated half-bridge GaN solution with minimized loop inductance. Before designing the converter, several GaN and Si devices were compared and loss analysis was conducted. Moreover, the impact of common source inductance from layout parasitic inductance was carefully investigated. Experimental test was conducted in buck mode operation at 48 -12 V, and results showed a peak efficiency of 97.8%.

• Wind and Structures
• /
• v.28 no.5
• /
• pp.271-284
• /
• 2019

This paper describes the application of a novel virtual prototyping methodology to wind turbine blade design. Numeric modelling data and experimental data about turbine blade geometry and structural/dynamical behaviour are combined to obtain an affordable digital twin model useful in reducing the undesirable uncertainties during the entire turbine lifecycle. Moreover, this model can be used to track and predict blade structural changes, due for example to structural damage, and to assess its remaining life. A new interactive and recursive process is proposed. It includes CAD geometry generation and finite element analyses, combined with experimental data gathered from the structural testing of a new generation wind turbine blade. The goal of the research is to show how the unique features of a complex wind turbine blade are considered in the virtual model updating process, fully exploiting the computational capabilities available to the designer in modern engineering. A composite Sandia National Laboratories Blade System Design Study (BSDS) turbine blade is used to exemplify the proposed process. Static, modal and fatigue experimental testing are conducted at Clarkson University Blade Test Facility. A digital model was created and updated to conform to all the information available from experimental testing. When an updated virtual digital model is available the performance of the blade during operation can be assessed with higher confidence.

• Journal of Research and Publication Ethics
• /
• v.1 no.2
• /
• pp.11-13
• /
• 2020

Purpose: The author wants to specify scope of research, identify without giving burden, prevent unfair identification of the author, admit of production of the outcome, enact rules of identification, and build up foundation of development. Also, this study defines scope of publication of outcome of research to prevent unfair identification of authors and admit of them. Research design, data and methodology: The study described literary research, standard research, phenomenon research, and empirical result without methodologies, statistical analysis and scientific test and investigated operation system of KODISA cases. Results: At publication of findings of the research, researchers shall identify the ones of production of the finding to allocate help of the research. Conclusions: Scientific journals shall be controlled to develop ability and to grow up and have a system. Researchers shall give direction of other scientific journals. The study made efforts to be a model. KODISA Edition Team shall make an effort to keep and develop. So far, no regulation of identification of authors has produced disturbance so terminologies should be uniformed. Researchers shall keep rules of identification of authors to uniform and regulate identification of authors, conditions of authors, and order and correspondent authors. KODISA enacted rules of identification of authors for the first time in Korea to develop science.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.6_2
• /
• pp.989-998
• /
• 2020

Recently, demands for large-capacity electronic loads are increasing in various industries such as a reliability test for the performance of a DC power supply device or a dummy-load for improving the stability of an independent microgrid to be actively built in the future. The electronic load required in these various fields requires an operation such as a continuously variable resistance load while minimizing the switching harmonic component generated in the electric load current in order to reduce the influence of interference from the load peripheral device. Electronic loads require a system that minimizes switching current ripple for load control. Therefore, in this paper, we propose a three-level module converter structure to reduce the current ripple of an electronic load, and a multilevel interleaved power converter topology to reduce the current ripple. The validity of the proposed electronic load, 3-level 6 interleaver converter, was verified by simulation and experiment. In addition, the user's convenience was provided by applying the emotional command curve interface method.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.22 no.4
• /
• pp.25-38
• /
• 2020

Impulse buying occurs when consumers feel an urge to impulsively buy a product without thoughtful consideration of why and for what reason they need the product. However, few efforts have been made to identify the impacts of perceived scarcity on the impulse buying of fashion products in mobile shopping malls. This study's objectives were to estimate, using structural equation model analysis, the impact of a scarcity message on browsing, feeling the urge to buy, and impulse buying of fashion products on mobile shopping malls. Data was collected from 206 customers who experienced to impulse buying fashion products via objective sampling. Structural equation modeling was used to test the hypotheses developed for the study. Results found evident effects of the scarcity message on the impulse buying of fashion products directly and indirectly. Additionally, consumers felt the urge to buy had a significant impact on the impulse buying of fashion products, whereas browsing had little impact on the impulse buying of fashion products. This is an expanded study to examine structural equation modeling of impulse buying of fashion products on mobile shopping malls. These results will contribute to a better understanding of the mechanisms that underlie the operation of an effective scarcity strategy for fashion products on mobile shopping malls.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.185-193
• /
• 2021

The system needs to be modified to improve the performance of the aircraft in operation or to satisfy the requirements of related laws. Appropriate standards are required for the technical skills for remodeling the aircraft system, design verification for airworthiness of the aircraft, and supplemental type certification (STC) certification procedures for type certification. This study analyzes the current status and demand of domestic aircraft remodeling, examines the current supplementary type certification procedure, and diagnoses the problem. In addition, as a result of researching measures to improve remodeling technology and certification capabilities to extend the life of the aircraft, improvements in the education system were derived to improve the domestic additional type certification process, such as approval of remodeling agencies and appointment of qualifications for each professional technician.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.4
• /
• pp.245-250
• /
• 2022

As location-based services using the Global Navigation Satellite System (GNSS) are diversified, concerns about the vulnerability of GNSS to radio disturbance and deception are also growing. Accordingly, countries that own and operate GNSS, such as the United States, Russia, and Europe, are also developing additional navigation systems that can compensate for GNSS' weaknesses. Among them, an R-Mode system that transmits navigation signals using an infrastructure that transmits differential GNSS (DGNSS) information using signals from the medium frequency band currently in operation is being developed in Europe and Korea. Since 2020, Korea has improved four DGNSS transmission stations, including Chungju, Eocheongdo, Palmido, and Socheongdo, to transmit R-Mode signals and test navigation performance in some parts of the West Sea. In this paper, we intend to establish a testbed for measuring the distance of R-Mode signals currently being transmitted and analyze the results. It is confirmed that the distance measurement performance varies depending on the antenna type, diurnal variation, and propagation path of the signal.

• Korea Trade Review
• /
• v.44 no.3
• /
• pp.25-42
• /
• 2019

This research examined the mediation effect of Workforce Agility (WA) on the relationship between environmental uncertainty and operational performance. We manipulated the control variables that are known to be affected by employment flexibility. Employment flexibility is caused by idiosyncratic characteristics of Korean port system. The analysis was tested by Baron & Kenny's method. The result indicates that each path of the proposed model is significant. Furthermore, the mediation effect was checked with the Sobel Test. The research revealed that environment uncertainty poses an indirect effect on operational performance. Both supply/demand uncertainty and technological uncertainty affected operational performance through the mediation effect of WA. Most of the distribution centers located in Busan Newport Distripark are operated in a bimodal labor (human resource) system which includes both permanent employees (workers) and temporary employees (workers). This empirical research provides theoretical and managerial implications by suggesting ways to increase efficiency in distribution center operation through WA enhancement, and to improve the unloading labor system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.3
• /
• pp.317-327
• /
• 2021

Low Frequency Active Sonobuoy(hereinafter referred to as LFAS) are being developed in Korea in consideration of compatibility with existing overseas sonobuoys, and a communication device for acoustic signals receiving and operating control of LFAS has been developed. The communication device needs to verify compatibility with the existing Sonobuoy, and for this purpose, the standardized Sonobuoy communication protocol was applied. The communication device is designed/manufactured to transmit the acoustic signal received in real time from the Sonobuoy through VHF band RF communication to the data processing device, and transmit CFS/CSG commands for operation control to the Sonobuoy through UHF band RF communication. In order to verify the manufactured communication device, the communication status and performance were verified by interlocking test through Ultra Electronics' PASS-II equipment and domestically developed electronic device of Sonobuoy. In addition, operability was verified through environmental tests, water tanks, and marine operations. In the future, the communication device of sonobuoy can be used for verification of the Sonobuoy developed in Korea.