• Structural Engineering and Mechanics
• /
• v.90 no.6
• /
• pp.611-633
• /
• 2024

This study intends to investigate the response of multi-cell (MC) beams to flexural loads in which the primary reinforcement is composed of both metallic and non-metallic materials. "Multi-cell" describes beam sections with multiple longitudinal voids separated by thin webs. Seven reinforced concrete MC beams measuring 300×200×1800 mm were tested under flexural loadings until failure. Two series of beams are formed, depending on the type of main reinforcement that is being used. A control RC beam with no openings and six MC beams are found in these two series. Series one and two are reinforced with metallic and non-metallic main reinforcement, respectively, in order to maintain a constant reinforcement ratio. The first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were among the structural parameters of the beams under investigation that were documented. The primary variables that vary are the kind of reinforcing materials that are utilized, as well as the kind and quantity of mesh layers. The outcomes of this study that looked at the experimental and numerical performance of ferrocement reinforced concrete MC beams are presented in this article. Nonlinear finite element analysis (NLFEA) was performed with ANSYS-16.0 software to demonstrate the behavior of composite MC beams with holes. A parametric study is also carried out to investigate the factors, such as opening size, that can most strongly affect the mechanical behavior of the suggested model. The experimental and numerical results obtained demonstrate that the FE simulations generated an acceptable degree of experimental value estimation. It's also important to demonstrate that, when compared to the control beam, the MC beam reinforced with geogrid mesh (MCGB) decreases its strength capacity by a maximum of 73.33%. In contrast, the minimum strength reduction value of 16.71% is observed in the MC beams reinforced with carbon reinforcing bars (MCCR). The findings of the experiments on MC beams with openings demonstrate that the presence of openings has a significant impact on the behavior of the beams, as there is a decrease in both the ultimate load and maximum deflection.

• The Journal of Pediatrics of Korean Medicine
• /
• v.38 no.3
• /
• pp.53-65
• /
• 2024

Objectives This study aimed to analyze herbal formulas for epilepsy recorded in nine herbal manuscripts regulated by the Ministry of Food and Drug Safety (MFDS). The goal was to identify the frequency and associations of the included herbs and to determine effective herbal combinations for epilepsy treatment. Methods The study analyzed formulas for epilepsy (癲癎) from nine herbal manuscripts regulated by the MFDS: 東醫寶鑑, 方藥合編, 鄕藥集成方, 景岳全書, 醫學入門, 濟衆新編, 廣濟秘笈, 東醫壽世保元, and 本草綱目. We examined the frequency of herbs, herb pairs, and their degree centrality within the network using Netminer 4.5. Results The analysis identified 143 different herbs across the 159 formulas. Frequently included herbs were 朱砂, 人蔘, 天南星, 麝香, 茯笭. The most common herb pairs included 朱砂-麝香, 茯笭-人蔘, 朱砂-天南星, 朱砂-人蔘, 朱砂-遠志, 半夏-天南星. Network analysis revealed four distinct clusters: Group 1 (tranquillizing by heavy settling and opening the orifices), Group 2 (dispelling phlegm and regulating qi), Group 3 (tonifying and tranquillizing), and Group 4 (pacifying the liver and extinguishing wind). Conclusion The herbal formulas for epilepsy in the nine MFDS-regulated manuscripts have antiepileptic effects through central nervous system sedation and neuroprotective actions.

• Journal of the Korea society of information convergence
• /
• v.5 no.2
• /
• pp.3-24
• /
• 2012

The purpose of this paper was to find out how the economic experiences of college students would affect their economic literacy via a survey with 494 D college students in Daegu city. First, economic literacy based on the general societal characteristics indicates 48.33 with females and 46.76 with males on average respectively, which shows a low score by and large. In the program divisions of college, nursing students showed the highest economic literacy, 58.67, followed by students in humanity and society, 53.56 students in engineering, 49.00 students in public health, 45.78 and students in art and physical education, 39.64. Levels of education of college students' father also affected economic Literacy of college students. College students whose father has a middle school diploma or lower revealed the highest economic literacy, 50.11. A second place is those whose father has a high school diploma, 49.57. The lowest score was recorded by those whose father has a graduate school degree. Even among the college students, those who just graduated from high school exhibited the highest economic literacy, 49.35, whereas those with a graduate school degree showed the lowest, 40.00 on average. In the economic literacy by financial empirical characteristics, college students who answered that they had an experience of opening a bankbook came up with 48.47, and those who answered that they had never opened a bankbook demonstrated a very low score of 30.20 on average. In the economic literacy by economic life variable, college students who never receive pocket money showed the highest score of 50.88, and those who get some pocket money whenever they need exhibited the lowest score of 44.23 on average. In the economic literacy by economic education variable, college students who answered that they had taken an economic education showed a score of 50.09. On the other hand, those who answered that they had never taken an economic education exhibited a score of 45.23 on average. College students who said that economic education is necessary showed a score of 50.24 in the economic literacy, whereas those who said that economic education is not necessary exhibited a score of 45.23 on average.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.15
• /
• pp.1-31
• /
• 1974

Introducing genes for earliness of wheat varieties is important to develop early varieties in winter wheat. In oder to obtain basic informations on the response of heading to the different day length and temperature treatments and on the inheritance of heading dates, experiments were conducted at the field and greenhouse of the Crop Experiment Station, Suwon. Varieties used in this experiments were, early variety Yecora F70, medium varieties Suke #169, Parker and Yukseung #3, and late varieties Changkwang, Bezostaia, Sturdy and Blueboy. The parents and F$_1$s of partial diallel crosses of above eight varieties were subjected the following four different treatments; 1. high temperature and long day, 2. high temperature and short day, 3. low temperature and long day, and 4. low temperature and short day. The same materials were grown also in field condition. Parents, F$_1$ and F$_2$ generation were grown also in both greenhouse under high temperature and short day and in field. The results obtained were summarized as follow: 1. No effects of temperature and daylength on the number of leaves on the main stem were found when -varieties were vernalized. The number of main stem leaves were fewer for spring type of varieties than for winter type of varieties. 2. The effects of temperature and daylength on the days to flag leaf opening were dependent on the speed of leaf emergence. The speed of leaf emergence were faster for lower leaves than for upper leaves. 3. The response to short day and long day (earliness of narrow sense) of varieties were found to be direct factor responsible to physiology of heading dates in vernalized varieties. Great difference of varieties to heading date was found in high temperature and short day treatment, but less differences were found in high temperature and long day, low temperature and long day and low temperature and short day treatments respectively. The least varietal difference for heading dates was found in the field condition. 4. Changkwang and Parker were found to be the most sensitive to short day treatment (photosensitive) and the heading of these varieties were delayed by short day treatment. No great varietal differences were found among other varieties. 5. Varietal differences of heading dates due to daylength were greater in high temperature than in low temperature. 6. Varietal differences of heading dates due to temperature were not great. but in general the heading dates of varieties were faster under high temperature than under low temperature. 7. Earliness of heading dates was due to partial dominance effect of genes involved in any condition. The degree of dominance was greater under short day than under long day treatment. 8. The varietal differences of heading date under high temperature and long day were due to earliness or narrow sense (response to long day) of varieties. The degree of dominance was greater for Yecora F70, spring type than for other winter type of varieties. No differences or less differences of degree of dominance was found among winter type of varieties. The estimated number of effective factor concerned in the earliness of narrow sense was one pair of allele with minor genes. 9. The insensitivity of varieties to short day treatment in heading dates was due to single dominant gene effect. Under the low temperature the sensitivity of varieties to short day treatment was less apparent. 10. The earliness of short day and long day (earliness of narrow sense) sensitivities of varieties appearea to be due to partial dominance of earliness over lateness. In strict sense, the degree of the dominance should be distinguished. 11. Dominant gene effects were found for the thermo-sensitivity of varieties, and the effect was less, significant than the earliness in narrow sense. 12. One pair of allele, ee and EE, for photosensitivity was responsible for the difference in the heading dates between Changkwang and Suke #169. Two pairs of alleles, ee, enen and EE, EnEn. appeared to be responsible for the difference between Changkwang and Yecora F70. The effects of EE and EnEn were, additive to the earliness and the effects of EE were greater than EnEn under short day. However, the effects of EE were not evident in long day but the effects of EnEn were observed in long day. 13. Two pairs of dominant alleles for the earliness were estimated from the analysis of F$_1$ diallels in the field but the effects of these alleles in F$_2$ were not apparent due to low temperature and short day treatment in early part of growth and high temperature and long day treatment in later part of growth. The F$_2$ population shows continuous variation due to environmental effects and due to other minor gene effects. 14. The heritabilities for heading dates were ranged from 0.51 to 0.72, indicating that the selection in early generation might be effective. The extent of heritability for heading dates varied with environments; higher magnitude of heritability was obtained in short day treatment and high temperature compared with long day and low temperature treatments. The heritabilities of heading date due to response to short day were 0.86 in high temperature and 0.76 in low temperature. The heritabilities of heading date due to temperature were not significantly high. 15. The correlation coefficients of heading dates to the number of grains per spike, weight of 1, 000 grains. and grain yield were positive and high, indicating the difficulties of selections of high yielding lines from early population. But no significant correlation coefficient was obtained between the earliness and the number of spikes, indicating the effective selection for high tillering from early varieties for high yielding.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.4
• /
• pp.48-59
• /
• 2014

This study was carried out to present raw data on managing the restored urban stream by studying the naturalized plants distributed in Gaeumjeong Stream, Changwon-si, Gyeongsangnam-do, Korea. The results were as follows. The numbers of naturalized plants were summarized as 45 taxa including 17 families, 36 genera, 43 species and 2 varieties. The invasive alien plants were 2 taxa including Ambrosia artemisiifolia and Lactuca sativa. The following summarizes the attributes of the naturalized plants. Most of the plants commonly originated from Europe and North America. The 5 naturalized degree that was widely distributed and had many individual was the most common. Until 1921, after the opening of 1 period was the most common in the introduced period. Section 12 had the highest NI at 41.9%, and the lowest, at 20.5%, in sections 9 and 19 were analyzed. Section 1 had the highest UI at 6.2%, whereas, the lowest, at 2.5%, was calculated in sections 19 and 20. Section 2 showed the highest DI at 16.7%. The first results of the analysis of the causes for the invasion of naturalized plants on the riverside and waterways, and physical factors and maintenance are directly affected. Second, sewage, muddy water and sediment deposits this naturalized plant caused by a chemical factor. Third, it is thought that invasive alien plants are irregular as it happens in biological factor. The proposed management plan naturalized plants, the first, disturbance caused by species management is a young object is removed immediately before flowering scape to eliminate or suppress the propagation of physical methods will be needed. Second, the fact that the national spread of native plant species and planting management does not provide space for the growth is very important. Third, agricultural land is disturbed by agricultural practices by interfering with the action of naturalized plants because the source of the river should be prohibited in agriculture. In the future, if we studied the naturalized plants distributed in restored streams located in Changwon-si, the characteristics of change in the ecosystem impact is expected to be beneficial.

• Korean Journal of Environmental Biology
• /
• v.21 no.3
• /
• pp.234-239
• /
• 2003

3-weeks old Commelina was transferred to and grown in Hoagland solution (($\pm 100 \mu M \;Cd^{2+}, 100 \mu M \;Cd^{2+}+10 \mu M\;IAA,100 \mu M\; Cd^{2+}+100 \mu M \; IAA,100 \mu M \; Cd^{2+} +1 \mu M \; IAA)$) for three weeks and then a number of physiological activities was investigated. In the control the length of stem was increased to 7 cm after 3 weeks, but in the treatment of $Cd^{2+}$, 2.0 cm was grown. In cases of IAA with $Cd^{2+}$, the growth of the plants was increased to 3.7 cm, 5.0 cm and 3.3 cm in 100 $\mu$M, 10 $\mu$M and 1 mM IAA respectively, Cadmium stimulated stomatal opening. The stomata, treated with $Cd^{2+}$ opened to n degree of about 6.1 $\mu\textrm{m}$, but the stomata, treated with no cadmium opened to 4.5 $\mu\textrm{m}$. In the treatment of various concentation of IAA with cadmium the stomata opend to about 1 $\mu\textrm{m}$ more than that of cadmium alone. Cadmium reduced total chlorophyll content up to 13% for 3 weeks. In the treatment of $Cd^{2+}$ ＋ IAA (10 $\mu$M and 100 $\mu$M) the clear change of total chlorophyll content was not observed, but in the addition of 1 mM IAA to $Cd^{2+}$ reduced the total chlorophyll content to about 9%. $Cd^{2+}$ reduced to 9% and 11% of Fv/Fm after two and three weeks respectively. In cases of IAA with $Cd^{2+}$, there were no clear changes of Fv/Fm. Cadmium reduced water potential to 67% after 3 weeks incubation, but in cases of IAA with $Cd^{2+}$, water potential was not clearly changed. Therefore, it could be concluded that the treatment of IAA showed clear alleviation of $Cd^{2+}$-induced several physiological toxicities.

• Women's Health Nursing
• /
• v.6 no.2
• /
• pp.234-257
• /
• 2000

At present in the medical care, the study and effort for producing health service to consider efficiency, effectiveness, and quality are urgently called for because of the difficulty in the keen competition according to the inter- nationalization and opening, the operation in the medical institution service testing system, the change in the medical policy of KDRGs, and the lack of the health care cost increasing rate. As an alternative, the case management for the new management system is introduced in the U.S., and the Critical Pathway that is the method designing the contents of activity and its result has been developed and applied in order to anticipate and manage the patient-outcome for the realization of the cost-effective case-management. Thus, this study intended to analyze the effectiveness to obtain by developing the Critical Pathway presented as the method to improve the quality-betterment and cost effectiveness through the continuous and consistent patient management for the hysterectomy patient and applying it to the real practice. As a study method, this author formed a conceptual framework through considering five Critical Pathway used in the current U.S. and three Critical Pathway presented in the literature to develop the Critical Pathway for the hysterectomy patient, and made out the preliminary Critical Pathway through reviewing the old chart. This author made the verified the validity of the expert group about the developed Critical Pathway, and to confirm the possibility of practice application, completed and settled the final Critical Pathway after using the Critical Pathway to the hysterectomy patient from March 1st to 15th, 1997. Finally, to analyze the application-effect of the developed Critical Pathway, this author offered health care service applying the Critical Pathway to the hysterectomy patient from April 15th to August 31th, 1997. The guide for the Critical Pathway was carried out in advance by outpatient setting nurse for outpatient setting visit before the operation, and after hospitalization the primary nurse monitored the execution degree on the every duty. After discharge this author surveyed the complication through phone visiting, and one month after discharge surveyed the patient's reaction about the offered service when outpatient setting visit and analyzed the result. The source for health care cost was obtained by the statistics about the hospital charge which was offered by the General Business Department. The results were as follows. 1. It was decided that the vertical line of the Critical Pathway was made up of eight items such as monitoring/assessment, treatment, line/drains, activity, medication, lab test, diet, patient teaching, and the horizontal line of the Critical Pathway was made up of from hospitalization to discharge. 2. After the analysis of service contents through reviewing the old chart, it was decided that the horizontal line of the preliminary Critical Pathway was made up of from hopitalization to fourth postoperative day, and the vertical line of it was divided into eight items which were the contents to occur with the time frame of the horizontal line. 3. After the verifying the validity of the expert group about the preliminary Critical Pathway, the horizontal line was amended from hopitalization to third postoperative day, and taking their consensus, some contents of the horizontal line was amended and deleted. 4. From March 1st to 15th, 1997, to confirm the clinical suitability, this author offered eight hysterectomy patients the medical service through the Critical Pathway. The result was that three of them could be discharged at the expected discharge day, and the others later than that day. Supplementing the preliminary Critical Pathway through analyzing the cause of that delay- case, this author developed the final Critical Pathway. 5. There were no significant differences between the experimental and the control group in the incidence of complication(P > 0.05). 6. The 92.4% of experimental group was satisfied with the Critical Pathway service. 7. The length of hospital stay of the experimental group offered with the Critical Pathway service was 4.6 days and there was a significant difference that it was 1.3 days shorter than that of the control group(t=-29.514, P=0.000). 8. There wsa a significant difference that the mean medical charge per one patient of the experimental group offered the Critical Pathway service was cheaper \124,150 than that of the control group(t=-9.826, P=0.000). 9. The result that the author assumed and analyzed hospital income with the rate of turning bed was assumed that the increase of hospital income was \63,245,072 for that study, and the income increase was expected with \68,704,864 for a year. The result that this author applied the Critical Pathway to the hysterectomy patient have no differences in the incidence of complication, high satisfaction with that service, and the length of hospital stay decreased in the experimental group, and the mean hospital charge per one patient decreased, but hospital income increased. Suggestions for further study and nursing practice are as follows. 1. The study to apply the Critical Pathway for a year, verify the validity, and measure the effect repeatedly is needed. 2. To apply and manage the Critical Pathway effectively, the study to computerize it is needed. 3. The study to develop hospital-based Critical Pathway about other diseases or procedure, and measure the effect is needed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.6
• /
• pp.468-477
• /
• 2019

The numerical model of Boussinesq approximation, which is mainly used for evaluating the port calmness due to the irregular waves, has a limit of applicability of lattice size in ports such as marinas with narrow port openings of around 30m. The SWASH model controls the partial reflection according to the depth, porosity coefficient and structure size when applying the reflected wave incident on the structure and terrain. In this study, the partial reflection evaluation at the front of the structure according to the bottom shape and the shape of the structure are examined. In order to evaluate the reproducibility of the model due to the diffraction waves entering the term, the area of incidence at right angles and inclination of the structure is constructed and compared with the diffraction theory suggested by Goda et al. (1978). The experimental results of the sectional structure reflectances calculated as the depth mean show reflectances similar to the approximate values of the reflectances presented by Stelling and Ahrens (1981). It is considered that the reflected wave is well reproduced according to the control of the reflected wave at the boundary and the shape and topography of the structure. Compared with previous studies to examine the diffraction of the wave incident from the breakwater opening, the wave incidence angle and the shape of the diffraction wave are very similar to the theoretical values, but both oblique and rectangular incidence In the case where the direction concentration is small, the diffraction degree is underestimated in some sections with the crest ratio of 0.5 to 0.6.