• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.820-826
• /
• 2014

It is well known that energy generated by a wind generator (WG) depends on the wind resources at the installation site. In other words, a WG installed in a high wind speed area can produce more energy than that in a low wind speed area. However, a WG installed at a low wind site can produce a similar amount of energy to that produced by a WG installed at a high wind site if the WG is designed with a rated wind speed corresponding to the mean wind speed of the site. In this paper, we investigated the power curve of a WG suitable for Korea's southwestern coast with a low mean wind speed to achieve a high capacity factor (CF). We collected the power curves of the 11 WGs of the 6 WG manufacturers. The probability density function of the wind speed on Korea's southwestern coast was modeled using the Weibull distribution. The annual energy production by the WG was calculated and then the CFs of all of the WGs were estimated and compared. The results indicated that the WG installed on the Korea's southwestern coast could obtain a CF higher than 40 % if it was designed with the lower rated speed corresponding to the mean wind speed at the installation site.

• Korean Journal of Construction Engineering and Management
• /
• v.3 no.4 s.12
• /
• pp.93-103
• /
• 2002

The reinforcement concrete work is the work affected by structural safety, durability, and schedule with form work. The domestic reinforcement concrete works have mainly worked the process of re-barfabrication/assembly on site. Finally it have low productivity. Then this paper analyzed waste factors and the process of re-bar fabrication/assembly on site for the productivity improvement and value-added productivity improvement. Waste factor analysis aims at maximizing value-added by the value analysis of re-bar fabrication and assembly on site. Finally, Value-AddingActivity(VAA)ismuchlessthan non-value adding activity. Especially, Non-Value-Adding Activity(NVAA) generates waste such as the activity steps, labors, equipments, materials, time, and soon. And it was non-flow production, over production, and analyzed into having to shift value. This paper aimsat maximizing value-addingactivity and minimizingnon value-addingactivity through waste factor analysis in process for the improvement of value added productivity.

• Journal of Korean Society of Forest Science
• /
• v.98 no.6
• /
• pp.652-658
• /
• 2009

This study was conducted to investigate the growing characteristics of oak sprouts which have developed naturally after fire and to suggest proper management system which is adapted for oak coppice forest by controlling the number of sprouts. We examined 3 burned sites and 9 unburned pine stands in Kangwondo. In the early years sprouts of oak coppice forest grew very slowly after fire compare to common oak coppice forest. But they had over than 10 cm of DBH after 15years, their DBH reached 10 cm and entered the stage of regeneration period. We also examined the effect of sprouts control. In the case of Quercus mongolica, stumps with 1 or 3 sprouts grew 1.3 m faster than the ones in the control stand. For Q. variabilis, stumps with 2 sprouts grew 0.9 m faster. In conclusion small timber production is proper for the oak coppice forest stand which is developed on the forest fire site and pruning or fertilizing is needed to shorten the production cycle.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.411-414
• /
• 2015

The purpose of this study is to conduct a comparative analysis between Korea and the United States of the supply process of unit modular housing at both the factory production phase and the transportation and lifting phase, as part of an attempt to invigorate the unit modular housing market in Korea. Unlike the practice in the United States, one of Korea's unique characteristics is that the floor is constructed with reinforced concrete and hot water heating system. To do this, the wet method in Korea is used that includes concrete placement, curing and constructing hot water floor heating system at the factory production phase, which results in a longer production time and also requires the lifting of heavier loads. In the United States, interior and exterior finishing works of modular housing are performed by different companies, and the distance between the unit module factory and the construction site is quite far. This kind of dualized production structure may cause confusion when it comes to schedule management, procurement management, and stock management. Moreover, problems caused by external environmental factors such as wind and rainfall were reported in the course of long-distance transportation. The results of this case comparison are expected to provide fundamental data that will reduce the amount of trial and error in the unit module production, transportation and lifting work in Korea, which has a comparatively small number of unit modular housing cases.

• Journal of Animal Environmental Science
• /
• v.9 no.2
• /
• pp.131-142
• /
• 2003

This on­site survey was performed by visiting sites in Israel and USA where broiler litter is studied, manufactured as feed and applied practically and interviewing experts related. Their advanced experiences, technologies and informations were collected, analyzed, compared with Korean situations and described on the text of this article. Although broiler litter has been successfully used as feed for at least 40 years in Israel and USA, its practice and application rate of the technologies related has been very slow in Korea. Many informations presented here will be very helpful for the successful on­site application of hygienically processed broiler litter as livestock feed. It's doubtless that these efforts to use broiler litter­like underutilized feed resource will result in considerable livestock production cost cut­down and environmental pollution prevention.

• Ocean and Polar Research
• /
• v.37 no.1
• /
• pp.23-35
• /
• 2015

A 450 m-long sediment section was recovered from Hole U1359D located at the eastern levee of the Jussieau submarine channel on the Wilkes Land continental rise (East Antarctica) during IODP Expedition 318. The age model for Hole U1359D was established by paleomagnetic stratigraphy and biostratigraphy, and the ages of core-top and core-bottom were estimated to be about 5 Ma and 13 Ma, respectively. Biogenic opal content during this period varied between 3% and 60%. In the Southern Ocean, high biogenic opal content generally represents warm climate characterized by the increased light availability due to the decrease of sea-ice distribution. The surface water productivity change in terms of biogenic opal content at about 10.2 Ma in the Wilkes Land continental rise was related to the development of Northern Component Water. After about 10.2 Ma, more production of Northern Component Water in the North Atlantic caused to increase heat transport to the Southern Ocean, resulting in the enhanced diatom production. Miocene isotope events (Mi4~Mi7), which are intermittent cooling intervals during the Miocene, appeared to be correlated to the low biogenic opal contents, but further refinement was required for precise correlation. Biogenic opal content decreased abruptly during 6 Ma to 5.5 Ma, which most likely corresponds to the Messinian salinity crisis. Short-term variation of biogenic opal content was related to the extent of sea-ice distribution associated with the location of Antarctic Polar Front that was controlled by glacial-interglacial paleoclimate change, although more precise dating and correlation will be necessary. Diatom production in the Wilkes Land continental rise increased during the interglacial periods because of the reduced sea-ice distribution and the southward movement of Antarctic Polar Front.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.204-205
• /
• 2015

Demands for free-form buildings are on the rise, but such building designs require most cost and longer construction schedule, with less constructability due to challenges in construction member production and installation. FCP production technology has been developed using CNC machine in a bid to resolve the difficulties of member production. Exterior finishing panels of free-form building design must be divided in size and shape that can be produced by CNC machine. To solve this problem, constraints of CNC machine and correlations between CNC machine and panel need to be reviewed. Thus, the purpose of this study is to analyze decision factors on free-form concrete panel sizes produced by CNC machines. Through this study, FCP size can be optimized, which in turn can lead to improved FCP productivity and aesthetical quality of free-form building designs determined by the pattern of exterior finishing panels. CNC machine-enabled free-form concrete panel production technology will apply on site in the future, which will not only maximize the economic benefits of the technology but also support shorter construction schedule and better constructability.

• Journal of Korean Society of Water and Wastewater
• /
• v.12 no.3
• /
• pp.65-74
• /
• 1998

Life cycle assessment (LCA) on two different sludge treatment systems, on-site treatment and pipe-collected intensive treatment was performed to estimate the environmental impact in the aspect of global warming effect. As a main parameter of the estimation, $CO_2$ was chosen and quantified through the whole life cycle of the treatment systems including construction, operation and dismantlement. In this study, the changes of $CO_2$ production unit (CPU) by up-scaling n currently used sludge treatment processes were also calculated. As the result, a larger amount of $CO_2$ was exhausted from the construction step of intensive treatment system than that of on-site treatment system, because an additional pipe-collection system was needed in intensive treatment system. However, the total amount of $CO_2$ exhausted from whole life cycle including not only construction and dismantlement but also 15 year-operation and maintenance was reduced by appling intensive treatment.

• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.380-392
• /
• 2000

A typical production-distribution system consist of three main echelons representing the retailer, distributors, and a factory each with an on-site warehouse. The system is sufficiently general and realistic to represent many industrial situations. However, decision functions and parameters have been selected to apply particularly to the production and distribution of consumer durables. The flows included in the model are materials, orders, and those information flows needed to support the material and order-rate decisions. In this work, a realistic production-distribution system has been used as a basic model, which consists of three sectors: retailer, distributor, and factory. That system is a nonlinear 25th-order continuous system interconnected between the echelons. Using a modern control algorithm, a typical multi-echelon production-distribution system using a dynamic controller is numerically simulated in the nominal plant and in the perturbed plant when the piecewise constant manufacturing decision is limited by a factory manufacturing upper-limit due to capital equipment, manpower, and factory lotsize.

• Journal of Environmental Science International
• /
• v.19 no.9
• /
• pp.1169-1175
• /
• 2010

A case study for the design of a wind farm in complex terrain was carried out using the wind farm site analysis software OpenWind, which has an open-source platform and is free to use. The Youngdeok Wind Farm, constructed on mountainous terrain in Korea, was chosen as a model site; the design process reproduced using OpenWind. A comparison of the positions of the wind turbine derived from the OpenWind optimization process and the current positions were in good agreement. The annual energy production predicted by OpenWind compared with the prediction by the micrositing software, WindSim, were also validated to within 1%. Therefore, it was confirmed that OpenWind can be used for a practical wind farm design project. It is also anticipating that this paper will provide a prototype process for the design of a wind farm site and offer a database for the post-evaluation of a constructed wind farm in Korea.