• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.54-64
• /
• 2006

To augment weakly damped lag mode stability of a hingeless helicopter rotor blade in hover, piezoelectric shunt with a resistor and an inductor circuits for passive damping has been studied. A shunted piezoceramics bonded to a flexure of rotor blade converts mechanical strain energy to electrical charge energy which is dissipated through the resistor in the R-L series shunt circuit. Because the fundamental lag mode frequency of a soft-in-plane hingeless helicopter rotor blade is generally about 0.7/rev, the design frequency of the blade system with flexure sets to be so. Experimentally, the measured lag mode frequency is 0.7227/rev under the short circuit condition. Therefore the suppression mode of this passive damping vibration absorber is adjusted to 0.7227/rev. As a result of damping enhancement using passive control, the passive damper which consists of a piezoelectric material and shunt circuits has a stabilizing effect on inherently weakly damped lag mode of the rotor blades, at the optimum tuning and resistor condition.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1633-1635
• /
• 1994

This paper presents the development technology of standard resistor divider for full lightning impulse voltage. The ability of high voltage bulk power equipment to withstand lighting stroke is usually evaluated by means of full lightning impulse voltage. Lightning impulse voltage test has been essential to evaluate the insulation performance of electrical power apparatus. Recently International standard (IEC 60) on high voltage measurement techniques is being revised and requests a formal traceability of high voltage measurements. Therefore, general interest for this area has grown considerably during last years, and several international intercomparisions have been completed already worldwide, i.e. Europe, Japan, America etc.. In this viewpoint, we have also investigated the standard resistor divider with shield, which satisfies the IEC recommendation.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.439-442
• /
• 2002

We present in this Paper a microwave Power sensor fabricated by a standard CMOS process and a bulk micromachining process. The sensor consists of a CPW transmission line, a resistor as a healer, and thermocouple arrays. An input microwave heater, the resistor so that the temperature rises proportionally to the microwave power and tile thermocouple arrays convert it to an electrical signal. The sensor uses air bridged 8round of CPW realized by wire bonding to reduce tile device size and cost and to improve the thermal impedance. Al/poly-Si junctions are used for the thermocouples. Poly-Si is used for tile resister and Aluminium is for transmission line. The resistor and hot junctions of the thermocouples are placed on a low stress silicon nitride diaphragm to minimize a thermal loss. The fabricated device operates properly from 1㎼ to 100㎽\ulcorner of input power. The sensitivity was measured to be ,3.2～4.7 V/W.

• Journal of the Korean Institute of Gas
• /
• v.8 no.1 s.22
• /
• pp.18-24
• /
• 2004

This study issues the component's ratings when low powered do intrinsic safety instrumentations using in flammable atmospheres. Test of reverse bias of zener diode characteristics and ignition characteristics test for power source consist of zener diode and resistor have done using IEC spark test apparatus. With this test, the ratings for zener diode and resistor are calculated and the design method of intrinsically safe power supply system is reported.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.457-458
• /
• 2007

We investigated a resistor network model for the horizontal AlInGaN LED. Adding the proposed current density dependent relative quantum efficiency, the power simulation can be also obtained. Comparing the simulation and the measurement results for the LED with the size of $350{\mu}m$, the model is reasonable to simulate the forward voltage and the light output power. Using this model we investigated the optimization of the position and the number of the finger electrodes in a given chip area. It shows that the center disposition of the p-finger electrode in p-area is optimal for the voltage and best for the power. And the minimum number of the n-finger electrodes is best for the power.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.3
• /
• pp.76-83
• /
• 2000

The continuous time signal system by development of CMOS technology have been receiving consideration attention. In this paper, Low pass filter using new CMOS floating resistor have been designed with cut off frequency for speech signal Processing. Especially a new floating resistor consisting entirely of CMOS devices in saturation has been developed. Linearity within $\pm$0.04% is achieved through nonlinearity via current mirrors over an applied range of $\pm$1V The frequency response exceeds 10MHz, and the resistors are expected to be useful in implementing integrated circuit active RC filters. The low pass filter designed using this method has simpler structure than switched capacitofilter. So reduce the chip area. The characteristics of the designed low pass filter using this method are simulated by pspice program.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.2 s.332
• /
• pp.15-22
• /
• 2005

Using the existing analog circuits, required resistor matching and Poly-Si TFT characteristics are investigated for the implementation of analog circuits to be integrated on System-on-Glass. Matching requirements on resistor values, threshold voltage and mobility of poly-Si TFT are derived as a function of the resolution of display system. Also, the effective mobility of poly-Si TFT required for the realization of source driver is analyzed for various panel sizes.

• Proceedings of the KIEE Conference
• /
• 1998.07e
• /
• pp.1586-1588
• /
• 1998

To use the EMTP, in this paper, a arcing horn is simulated by non-linear resistor and inductor element using TACS, a tower by distributed parameter model, and lines as K. C. Lee model. Changing lightning current characteristics, lightning position, and tower footing resistor value, we analysis multi-phase flashover characteristics in 765 kV transmission line.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.4
• /
• pp.1-5
• /
• 1970

This presents the way in shich the input impedance, and the output waveform of the line discriminator are influenced by a discrepancy of less than $\pm$10% in the coupling resistor resistance from the optium value(Characteristic impedance of the transmission line used in the line discriminator)

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.33-38
• /
• 1996

In thick film resistors, the characteristics of the frit and the reaction between glass frit and conductor material play an important role for their electrical properties. In this study, various glass frits in the system of $60RO{\cdot}20SiO_2$ $15B_2O_3{\cdot}5Al_2O_3$(RO=PbO, ZnO, CdO; mole%) were mixed with $RuO_2$ and coated on 96% alumina substrate. Only the glass frit containing PbO was reacted with $RuO_2$in$RuO_{2+}$-thick film resistor and produced the new crystalline phase of $Pb_2Ru_2O_{65}$. Their electrical resistivities strongly depend on the amount of $Pb_2Ru_2O_{65}$ crystalline phase obtained, which varied with firing temperature. The sheet resistivities of these resistors were varied from $10^3\; to\; 10^6\;{\Omega}/{\Box}$ depending on heat treatment, and the absolute value of TCR was decreased as the heat treatment temperature increaed. However, $RuO_2$ did not reacted with the glass frits containing ZnO nor CdO, and the resulting showed very high sheet resistivities.