• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• 태양에너지
• /
• 제20권1호
• /
• pp.55-62
• /
• 2000

An experimental study on the stratified fluids with water and silicon oil of same volume in the cavity with upper cooling surface was carried out to investigate the flow characteristics, heat transfer through the interface of fluids, and the applications of thermal behaviors in a square cavity. The experiments were performed with variation of initial temperature and cooling surface temperature. The temperature drop of oil was faster than that of water and freezing was initiated from the interface of oil and water and propagated downward. For the water above $4^{\circ}C$, the cooling rate was faster than that below $4^{\circ}C$ and showed almost same temperature distribution but for the water that of below $4^{\circ}C$, it showed the stable stratified temperature distribution. The lower the initial temperature and the higher the cooling surface temperature was, the longer the supercooling duration.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.83-89
• /
• 2000

This paper presents a pressure drop correlation for evaporation and condensation of alternative refrigerant with oil in micro-fin tubes. The correlation was developed from a data base consisting of oil-free pure and mixed refrigerants in micro-fin tube; Rl25 R134a. R32 R410a(R32/R125 50/50% mass), R22, R407c(R32/R125/R134a, 23/25/52% mass) and R32/R134a(25/75% mass). The micro-fin tube used in this paper had 60 0.2mm high fins with a 18 helix angle. The cross sectional flow area $(A_c)$ was $60.8 mm^2$ giving an equivalent smooth diameter$(D_e)$ of 8.8mm. The hydraulic diameter $(D_h)$ was estimated to the 5.45mm. The new correlation was obtained by replacing the friction factor and the tube-diameter in Bo Pierre correlation by a friction factor derived from pressure drop data for a micro-fin tube and the hydraulic diameter, respectively. This correlation was also used to predict some pressure data with a lubricant after using a mixing viscosity rule of lubricants and refrigerants. As a result, the new correlation was also well predicted to the measured data within a mean deviation of 19.0%.

• Journal of Korea Trade
• /
• 제23권8호
• /
• pp.1-26
• /
• 2019

Purpose - This paper investigates the recent trade collapse, recovery, and prolonged slowdown to shed light on the discussions about whether the current slowdown is structural or cyclical. I examine structural, cyclical, and heterogeneous aspects of the recent trade trends using detailed statistics of a small open economy, South Korea, whose economic success and growth have been heavily dependent on exports. Design/methodology - I use both aggregated and disaggregated trade statistics of South Korea. I apply the following methodologies: 1) I decompose the trade growth into the extensive and the intensive margin and observe the effect of prices over time. 2) I estimate the trade-income elasticities focusing on the world's import demand, separately for goods from the world and from Korea. 3) I compare the drop in goods exports in slowdown and trade collapse, which are the two unusual periods in the recent history when world trade has substantially dropped altogether. Findings - I show that while the last drop of trade after 2015 has cyclical aspects, there is evidence that the continued slowdown from 2012 is structural: 1) the so-called 'China factor' is found in the analysis of trade-income elasticity of the world and China for imports from Korea. 2) The bilateral trade barriers between Korea and its principal trading partners are universally tightening. 3) Firm sizes, destination countries, and the mode of transactions affect disaggregated trade flows during the slowdown periods. Originality/value - This paper contributes to the debate regarding whether the current trade slowdown is structural or cyclical. I provide two concrete evidence that the export drop in 2015 stems from low oil prices: one is the divergence of Korean export value index from its export quantity index, which started in late 2014 when oil prices plunged. I also contribute to the literature by providing evidence that Korea's trade barriers with important trading partners are steadily increasing since 2012 as the protectionist measures toward Korea's export products are steeply increasing after the global financial crisis.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.189-194
• /
• 2005

The evaporation heat transfer and pressure drop of $CO_2$ in a small diameter tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator(test section). The test section was made of a horizontal stainless steel tube with the inner diameter of 4.57 mm, and length of 4 m. The experiments were conducted at mass flux of 200 to 700 $kg/m^2s$, saturation temperature of $0^{\circ}C$ to $20^{\circ}C$, and heat flux of 10 to 20 $kW/m^2$ . The test results showed the evaporation heat transfer of $CO_2$ has great effect on more nucleate boiling than convective boiling. The evaporation heat transfer coefficients of $CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The evaporation pressure drop of C02 are highly dependent on the mass flux. In comparison with test results and existing correlations, correlations failed to predict the evaporation heat transfer coefficient and pressure drop of $CO_2$, therefore, it is necessary to develop reliable and accurate predictions determining the evaporation heat transfer coefficient and friction pressure drop of $CO_2$ in a horizontal tube.

• 한국산학기술학회논문지
• /
• 제13권2호
• /
• pp.516-521
• /
• 2012

본 논문은 전산해석을 수행하여 가솔린 엔진에 적용되는 오일분리기의 성능을 비교/분석하여 적정한 오일분리기를 선정하고자 하였다. 두 가지 다른 형태의 오일분리기를 해석하였으며, 포집된 오일입자를 분석하여 포집성능을 대표하는 d50과 포집효율을 계산하였다. 계산결과 모델 A는 우수한 포집성능과 효율을 나타내었고, 모델 B는 양호한 압력강하량 특성을 보였다. 크랭크 케이스의 압력이 높지 않고, 오일소모량이 적은 일반적인 가솔린 엔진의 경우에는 압력강하량이 우수한 모델 B 오일분리기를 추천한다. 크랭크 케이스의 압력이 높고, 오일소모량이 큰 엔진, 특히 오일입자의 오염이 치명적인 특수 배기처리장치를 장착한 엔진에는 큰 압력강하량과 우수한 포집효율을 가지는 모델 A 오일분리기를 추천한다.

• Korea-Australia Rheology Journal
• /
• 제21권4호
• /
• pp.269-280
• /
• 2009

The drop formation dynamics of a shear thinning, elastic, yield stress ($\tau_o$) fluid (Carbopol 980 (poly(acrylic acid)) dispersions) in silicone oil has been investigated in a flow-focusing microfluidic channel. The rheological character of each solution investigated varied from Netwonian-like through to highly non-Newtonian and was varied by changing the degree of neutralization along the poly (acrylic acid) backbone. We have observed that the drop size of these non-Newtonian fluids (regardless of the degree of neutralisation) showed bimodal behaviour. At first we observed increases in drop size with increasing viscosity ratio (viscosity ratio=viscosity of dispersed phase (DP)/viscosity of continuous phase (CP)) at low flowrates of the continuous phases, and thereafter, decreasing drop sizes as the flow rate of the CP increases past a critical value. Only at the onset of pinching and during the high extensional deformation during pinch-off of a drop are any differences in the non-Newtonian characteristics of these fluids, that is extents of shear thinning, elasticity and yield stress ($\tau_o$), apparent. Changes in these break-off dynamics resulted in the observed differences in the number and size distribution of secondary drops during pinch-off for both fluid classes, Newtonian-like and non-Newtonian fluids. In the case of the Newtonian-like drops, a secondary drop was generated by the onset of necking and breakup at both ends of the filament, akin to end-pinching behavior. This pinch-off behavior was observed to be unaffected by changes in viscosity ratio, over the range explored. Meanwhile, in the case of the non-Newtonian solutions, discrete differences in behaviour were observed, believed to be attributable to each of the non-Newtonian properties of shear thinning, elasticity and yield stress. The presence of a yield stress ($\tau_o$), when coupled with slow flow rates or low viscosities of the CP, reduced the drop size compared to the Newtonian-like Carbopol dispersions of much lower viscosity. The presence of shear thinning resulted in a rapid necking event post onset, a decrease in primary droplet size and, in some cases, an increase in the rate of drop production. The presence of elasticity during the extensional flow imposed by the necking event allowed for the extended maintenance of the filament, as observed previously for dilute solutions of linear polymers during drop break-up.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.81-82
• /
• 2011

This paper is to compare and analyze WOE created by emulsifying waste oil & WOES added by stimulant with the existing SR in order to solve the problem of strength and reduction in fluidity occurring in time of the use of waste oil to reduce the autogenous shrinkage of high strength mortar. As experimental results, in case of WOE, there almost never happened a drop in fluidity at 1% replacement and compressive strength also showed the strength value similar to Plain. On the other hand, the effect of strength improvement consequent upon the use of stimulant was found to be insufficient. The change of autogenous shrinkage generally showed a better reduction effect in shrinkage comparing to Plain. In case of WOE1, reduction effect in autogenous shrinkage was found to be more excellent than the existing SR. Accordingly, WOE1 is analyzed to be desirable if reduction in autogenous shrinkage, strength & up to the aspect of fluidity are taken into consideration.

• 수산해양기술연구
• /
• 제23권3호
• /
• pp.17-17
• /
• 1987

유압관로에서의 캐비테이션 발생 기구를 조사할 목적으로, 과도흐름에 수반하여 발생하는 캐비테이션 초생에 관한 실험 및 압력이 급강하 할 때의 기포 성장에 대한 계산을 행하였다. 실험에서 얻은 결과를 기초로 한 계산에서, 작동유가 절대압 영이하의 부압에 노출되어도 캐비테이션이 발생하지 않을 정도의 장력을 갖기 위해서는 소위 말하는 기포(기포 주위의 액체가 연속체로 간주될 수 있을 정도의 크기를 갖는 기포)가 유중에 존재할 가능성은 거의 없음이 입증되었다.

• 한국분무공학회지
• /
• 제13권1호
• /
• pp.42-50
• /
• 2008

In the present work, atomization characteristics of shear-thinning liquid slurry discharging from fan spray nozzles were studied experimentally for spray painting applications. The effects of solid particle size and concentration on the properties (especially on the viscosity) of suspensions and mean drop size were examined by using model fluids. In the range of low particle concentration (below 3 wt%), the fluid viscosity was primarily determined by the particle size. On the other hand, in the range of high particle concentration (higher than 10 wt%), the agglomeration phenomenon and the oil absorption capability of solid particles played major roles in determining the fluid viscosity. In the high concentration region, which most of the paints belong to, the fluid became more viscous and the shear thinning behavior appeared more prominent as the particle concentration was increased. In this region, mean drop size(SMD) decreased more rapidly with the increase of the injection pressure. Also, SMD became larger with the higher particle concentration and the larger particle size.