• International journal of advanced smart convergence
• /
• v.4 no.1
• /
• pp.54-63
• /
• 2015

Increasing air pollution levels and the global oil crisis has become a major hindrance in the growth of our automobile sector. Traditional Internal Combustion engines running on non-renewable fuels are proving to be the major culprit for the harmful effects on environment. With few modifications and also with assistance of few additional components current small SI engines can be modified into a pneumatic engine (commonly known as Compressed Air Engines) without much technical complications where the working fluid is compressed air. The working principle is very basic as adiabatic expansion of the compressed air takes place inside the cylinder pushing the piston downwards creating enough MEP to run the crank shaft at decent RPM. With the assistance of new research and development on pneumatic engines can explore the potential of pneumatic engines as a viable option over IC engines. The paper deals with analysis on RPM variation with corresponding compressed air injection at different crank angles from TDC keeping constant injection time period. Similarly RPM variation can also be observed at different injection pressures with similar injection angle variation. A setup employing a combination of magnetic switch (reed switch), magnets and solenoid valve is used in order to injection timing control. A conclusive data is obtained after detailed analysis of RPM variation that can be employed in newly modified pneumatic engines in order to enhance the running performance. With a number of benefits offered by pneumatic engine over IC engines such as no emissions, better efficiency, low running cost, light weight accompanied by optimized injection conditions can cause a significant development in pneumatic engines without any major alteration.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.363-370
• /
• 2009

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. Hot air heaters of 256,246 units have been supplied as main greenhouse heating equipment until 2008 and greenhouse heating cost has reached to 620 billions won in Korea. In order to improve the thermal efficiency of the hot air heater and to reduce the expenses for greenhouse heating, prototype hot air heater was manufactured and tested in this experiment. The heat exchanger of tested prototype hot air heater was circular and hexagonal pipe type and inline and stagger arrangement type. Capacity of the heating was 43,062 kJ/h and total heat transfer area of the heat exchanger was $10.728\;m^2$. According to the performance test, it could supply heat of 38,240 to 35,100 kJ/h depending on the fan motor speed of 1,740~1,220 rpm, respectively. Thermal efficiency of hot air heater was 87.0% to 80.8% in the same conditions. As a result, thermal efficiency of hot air heater with hexagonal pipe-stagger arrangement heat exchanger developed in this study was higher 10.2% than that of conventional hot air heater and heating energy saving rate of 14.3% increased.

• Spatial Information Research
• /
• v.18 no.3
• /
• pp.85-94
• /
• 2010

This study presented a method to allocate RFID reader sites for the weekly no driving day program. In resent years, three metropolitan cities begin to operate the system to resolve the traffic jam, air pollution, and oil cost, which is expected to be operated across the country in a few years. In this regard, the accurate verification of the observance of the cars which are participated in the system is needed so that the more benefits are rewarded to observing participants but not violating ones. Thus, this study distinguished road sections where the system of the Daegu metropolitan city cannot determine the observance of the participated cars when the cars detour the RFID readers by employing a set of data from the traffic census, digital maps, and terrestrial photographs of the superstructures on the roads. Then, the appropriate sites for additional RFID readers were determined based on those sections in the road network and the types of the road superstructures.

• Transactions of the KSME C: Technology and Education
• /
• v.1 no.1
• /
• pp.49-57
• /
• 2013

The dimensioning accidental loads have been selected through suitable quantitative risk assessment and generally utilized important factors for offshore facility design. The fire hazard can be quantified with dimensioning fire loads. The main purposes of fire protection are to maintain the functionality of safety systems within evacuation period and to prevent the escalation from initial fire to uncontrolled catastrophic fire. This paper introduces the applications and the design methods of active and passive fire protections as representative measures of fire protection of offshore facilities. The passive fire protection requires the high initial installation cost and much difficulty on the operation of facilities and their maintenance. The oil major clients have asked the design contractors of offshore facilities to optimize the amount of passive fire protection with relevant engineering technology recently.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.92-99
• /
• 2013

High oil price and global warming problem are being continued all over the world. For this reason, fuel economy and emission of greenhouse gas are regulated by law in many countries. Therefore many companies are researching and producing hybrid electric vehicles (HEVs) which substitute conventional internal combustion engine vehicle. However, these researches and productions are restricted to mainly passenger cars. Because of cost and physical problems, commercial vehicles are difficult to evaluate fuel economy. So simulations are important and it is necessary to know how sensitive parameters that enter into simulation affect. In this paper, forward simulations using AVL Cruise were conducted for analysis of fuel economy for parallel hybrid bus and were repeated by changing each parameter. Based on these results, root mean square errors (RMSE) are calculated for analysis of fuel economy sensitivity. The number of target parameters are 15. These parameters were classified with high and low sensitivity parameter relatively.

• Membrane and Water Treatment
• /
• v.11 no.2
• /
• pp.97-109
• /
• 2020

Membrane fouling is the main drawback of membrane technology. Frequent membrane cleaning and membrane replacement are, therefore, required to reduce membrane fouling that causes permeate flux reduction, lower rejection, or higher operating pressure. Studies have proved that the alteration of membrane properties is the key controlling factor in lessening membrane fouling. Among stimuli-responsive membranes, thermo-responsive membrane is the most popular, with a drastic phase transition and swelling-shrinking behavior caused by the temperature change. In this study, the thermo-responsive ability of two commercial membranes, PolyCera® Titan membrane and PolyCera® Hydro membrane, at different temperatures was studied on the antifouling function of the membrane in palm oil mill effluent (POME) treatment. The evaluation of the membrane's thermo-responsive ability was done through three cycles of adsorption (fouling) and desorption (defouling) processes in a membrane filtration process. The experimental result depicted that PolyCera® Hydro membrane had a higher membrane permeability of 67.869 L/㎡.h.bar than PolyCera® Titan membrane at 46.011 L/㎡.h.bar. However, the high membrane permeability of PolyCera® Hydro membrane was compensated with low removal efficiency. PolyCera® Titan membrane with a smaller mean pore size had better rejection performance than PolyCera® Hydro membrane for all tested parameters. On the other hand, PolyCera® Titan membrane had a better hydrodynamic cleaning efficiency than PolyCera® Hydro membrane regardless of the hydrodynamic cleaning temperature. The best hydrodynamic cleaning performed by PolyCera® Titan membrane was at 35℃ with the flux recovery ratio (FRR) of 99.17 ± 1.43%. The excellent thermo-responsive properties of the PolyCera® Titan membrane could eventually reduce the frequency of membrane replacement and lessen the use of chemicals for membrane cleaning. This outstanding exploration helps to provide a solution to the chemical industry and membrane technology bottleneck, which is the membrane fouling, thus reducing the operating cost incurred by the membrane fouling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.21-27
• /
• 2018

FRN (Full range Naphtha) is distilled from crude oil in a Naphtha Splitter Unit and is separated into the Light Straight Naphtha, Heavy Naphtha, and kerosene according to the boiling point in sequence. This separation is conducted using a series of binary-like columns. In this separation method, the energy consumed in the reboiler is used to separate the heaviest components and most of this energy is discarded as vapor condensation in the overhead cooler. In this study, the first two columns of the separation process are replaced with the Petlyuk column. A structural design was exercised by a stage to stage computation with an ideal tray efficiency in the equilibrium condition. Compared to the performance of a conventional system of 3-column model, the design outcome indicates that the procedure is simple and efficient because the composition of the liquid component in the column tray was designed to be similar to the equilibrium distillation curve. An analysis of the performance of the new process indicated an energy saving of 12.3% under same total number of trays and with a saving of the initial investment cost.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.3
• /
• pp.961-966
• /
• 2012

The concern about vacuum glass is enhanced as society gets greener and becomes more concerned about energy savings due to the rising cost of oil. The glass edge sealing process needs the high reliability among the main process for the vacuum glass development in order to maintain between the two glass by the vacuum. In this paper, the process of the edge sealing was performed by using the hydrogen mixture gas which is the high density heat source unlike the traditional method glass edge sealing by using the frit as the soldering process. The ambient temperature in the electric furnace was set in the edge sealing to prevents the thermal impact and transformation of the glasses and the temperature distribution uniformity was measured. The parameter of the edge sealing was set through the basic test and the mathematical relation with the area of the glass edge parts according to the parameter was drawn using the multiple regression analysis method.

• Journal of the Korean Society of Systems Engineering
• /
• v.11 no.1
• /
• pp.81-93
• /
• 2015

Steam Reforming H2 Generation (SRH2G) System is a chemical process to produce hydrogen through steam reforming of hydrocarbon. Largely speaking, there are two types of materials for the SRH2G: 1) Oil and coal, and 2)Natural Gas such as shale gas. From the perspective of cost, quality (purity), and environmental burden (pollution), the latter is much more desirable than the former. For this reason, research on SRH2G using natural gas is actively carried out, and implemented and operated in the various industry. In this paper, we develop a natural gas based SRH2G system via systems engineering approach. Specifically, we first derived stakeholder requirements, followed by systems requirements and finally system architecture via a tailored SE process for plant (called Plant Systems Engineering (PSE) process) based on ISO/IEC 15288. The developed method was applied to iron and steel plant as a case study. Through the case study, by the SE approach, we were convinced that a successful system satisfying stakeholders' requirements within the given constraints can be developed, verified and validated.

• Journal of Nutrition and Health
• /
• v.14 no.1
• /
• pp.1-8
• /
• 1981

The purpose of this nutritional survey on the actual conditions of group feeding is to be of value for promoting the health of the blue collar workers through consice understanding of food intake trends in businesses as well as realizing our desirable target. The results of the survey are summarized as follow. 1, Status of food economics 1) The average feeding cost amounts to 453 won per day per person. 2) The average school years of food buyers were 12.3 years, cookers were 12.0 years and dieticians were 14.5 years. 3) Kerosene(57.6%), gas(24.2%), electric(12. 1%) and cool briguette(6.1%) were used for fuel. 2. Status of food intake The average food intake per person per day in surveyed businesses was 1193.4g. The total intake of food was consisted of 42% grains, 40.4% vegetables, 4.7% legumes, 4.5% fish and shellfish, 4.0% potatoes, 1.6% meats, 1.0% seasonings. 0.8% eggs, 0.5% sea weeds, 0.3% oil and fats, 0.1% sugar. These findings led us to the conclusion that workers in the surveyed businesses retied heavily on plant foods. 3. Status of nutrient intakes 1) The average intake of calorie was 2752.6 kcal per day, which was slightly higher than 2,700 kcal of RDA. Though the quantity was above the level of RDA, it was largely from plant foods. 2) The average intake of protein was 84.7g per day, which was slightly higher than 80g of RDA. 3) The average intake of fat was 26g per day, which was much lower than 36g of RDA. 4) The averse intake of calcium was 532.3mg per day, which was lower than 600mg of RDA. 5) The average iron intake was 9.8mg per day, which was much lower than 10mg of RDA and 18mg of HDA for women. 6) Intakes of vitamin group were high. Especially, intake of vitamin A was 2-3 times higher than RDA and intake of vitamin C and niacin were 2 times higher than RDA.