• 한국방재학회 논문집
• /
• 제1권1호
• /
• pp.157-163
• /
• 2001

본 연구의 목적은 청정실 내부에서 가상의 화재가 발생할 경우 화재 확산 및 연기의 전파 현상을 예측하기 위하여 실시하였다. 청정실 내의 화재로 인한 온도 및 속도분포의 해석은 유한체적법을 이용한 수치적 방법으로 해석하였으며 난류유동장의 계산은 표준 $k-{\varepsilon}$ 모델을 적용하여 실시하였다. 본 연구 결과는 화재발생 후 150초가 지난 후에는 화재가 완전히 성장한 것으로 나타났으며 이 경우 환기장치는 화재가 완전히 성장한 후에 정지하는 것으로 가정하였다. 연기의 질량분율은 온도 분포와 거의 유사한 것으로 나타났다. 따라서 청정실에서 화재가 발생할 경우 화재 성장이 60초 내에 전공간의 $20{\sim}30%$까지 확산되므로 내부에 있는 사람은 30초 이내에 대피하는 것이 바람직하다.

• International Journal of Korean Welding Society
• /
• 제2권2호
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• 한국농공학회논문집
• /
• 제57권5호
• /
• pp.113-122
• /
• 2015

This study aims to evaluate future stream flow by the operation of agricultural reservoir group at the upper stream of the Miho River. Four agricultural reservoirs with storage capacities greater than one million cubic meters within the watershed were selected, and the RCP 8.5 climate change scenario was applied to simulate reservoir water storage and stream flow assuming that there are no changes in greenhouse gas reduction. Reservoir operation scenarios were classified into four types depending on the supply of instream flow, and the water supply reliability of each reservoir in terms of water supply under different reservoir operation scenarios was analyzed. In addition, flow duration at the watershed outlet was evaluated. The results showed that the overall run-off ratio of the upper stream watershed of the Miho River will decrease in the future. The future water supply reliability of the reservoirs decreased even when they did not supply instream flow during their operation. It would also be difficult to supply instream flow during non-irrigation periods or throughout the year (January-December); however, operating the reservoir based on the operating rule curve should improve the water supply reliability. In particular, when instream flow was not supplied, high flow increased, and when it was supplied, abundant flow, ordinary flow, and low flow increased. Drought flow increased when instream flow was supplied throughout the year. Therefore, the operation of the agricultural reservoirs in accordance with the operating rule curve is expected to increase stream flow by controlling the water supply to cope with climate change.

• Journal of Trauma and Injury
• /
• 제27권4호
• /
• pp.229-232
• /
• 2014

A 55 year-old man hit a vehicle while riding a bicycle. He was diagnosed as left hemopneumothorax, multiple rib fracture, cerebral hemorrhage, and skull fracture. Initially he suffered from hypoxia requiring 100% oxygen with a mechanical ventilator. Finally he became hypotensive. Venovenous extracorporeal membrane oxygenation (ECMO) was initiated to support patient's gas exchange. Because hypotension and left ventricular dysfuction persisted, we converted the mode of support to veno-arterio-venous ECMO. Over four days of intensive care, we could wean off ECMO. The patient went to rehabilitation facility after 45 days of hospitalization. Although trauma and bleeding are considered as relative contraindication of ECMO, careful decision making and management may enable us to use ECMO for trauma-related refractory heart and/or lung failure.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.436-437
• /
• 2012

Double patterning technology (DPT) has been suggested as a promising candidates of the next generation lithography technology in FLASH and DRAM manufacturing in sub-40nm technology node. DPT enables to overcome the physical limitation of optical lithography, and it is expected to be continued as long as e-beam lithography takes place in manufacturing. Several different processes for DPT are currently available in practice, and they are litho-litho-etch (LLE), litho-etch-litho-etch (LELE), litho-freeze-litho-etch (LFLE), and self-aligned double patterning (SADP) [1]. The self-aligned approach is regarded as more suitable for mass production, but it requires precise control of sidewall space etch profile for the exact definition of hard mask layer. In this paper, we propose etch end point detection (EPD) in spacer etching to precisely control sidewall profile in SADP. Conventional etch EPD notify the end point after or on-set of a layer being etched is removed, but the EPD in spacer etch should land-off exactly after surface removal while the spacer is still remained. Precise control of real-time in-situ EPD may help to control the size of spacer to realize desired pattern geometry. To demonstrate the capability of spacer-etch EPD, we fabricated metal line structure on silicon dioxide layer and spacer deposition layer with silicon nitride. While blanket etch of the spacer layer takes place in inductively coupled plasma-reactive ion etching (ICP-RIE), in-situ monitoring of plasma chemistry is performed using optical emission spectroscopy (OES), and the acquired data is stored in a local computer. Through offline analysis of the acquired OES data with respect to etch gas and by-product chemistry, a representative EPD time traces signal is derived. We found that the SE-EPD is useful for precise control of spacer etching in DPT, and we are continuously developing real-time SE-EPD methodology employing cumulative sum (CUSUM) control chart [2].

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.334-334
• /
• 2012

Transparent oxide semiconductors have recently attracted much attention as channel layer materials due to advantageous electrical and optical characteristics such as high mobility, high stability, and good transparency. In addition, transparent oxide semiconductor can be fabricated at low temperature with a low production cost and it permits highly uniform devices such as large area displays. A variety of thin film transistors (TFTs) have been studied including ZnO, InZnO, and InGaZnO as the channel layer. Recently, there are many studies for substitution of Ga in InGaZnO TFTs due to their problem, such as stability of devices. In this work, new quaternary compound materials, tantalum-indium-tin oxide (TaInSnO) thin films were fabricated by using co-sputtering and used for the active channel layer in thin film transistors (TFTs). We deposited TaInSnO films in a mixed gas (O2+Ar) atmosphere by co-sputtering from Ta and ITO targets, respectively. The electric characteristics of TaInSnO TFTs and thin films were investigated according to the RF power applied to the $Ta_2O_5$ target. The addition of Ta elements could suppress the formation of oxygen vacancies because of the stronger oxidation tendency of Ta relative to that of In or Sn. Therefore the free carrier density decreased with increasing RF power of $Ta_2O_5$ in TaInSnO thin film. The optimized characteristics of TaInSnO TFT showed an on/off current ratio of $1.4{\times}108$, a threshold voltage of 2.91 V, a field-effect mobility of 2.37 cm2/Vs, and a subthreshold swing of 0.48 V/dec.

• 자원환경지질
• /
• 제26권1호
• /
• pp.55-65
• /
• 1993

Udo Island, some 3 km off the coast of Sungsan Peninsula at the eastern promontory of Cheju Island, occurs in such a regular pattern on the sequences which reprent an excellent example of an eruptive cycle. The island comprises a horseshoe-shaped tuff cone, a nested cinder cone on the crater floor, and a lava delta which extends over northwest from the moat between two cones. The volcanic sequences suggest volcanic processes that start with emergent Surtseyan eruption, progress through Strombolian eruption and end with lava effusion followed by reworking of smooth tephra on the tuff cone. Eruptive environment and hydrology of vent area in the Udo tuff cone are poorly constrained because the stratigraphic units under the tuff cone are unknown. It is thoughl, however, that the tuff cone could be mainly emergent because the present cone deposits show no evidence of marine reworking, and standing body of sea water could play a great role. The emergent volcano is characterized by distinctive steam-explosivity that results primarily from a bulk interaction between rapidly ascending magma and a highly mobile slurry. The sea water gets into the vent by flooding accross or through the top or breach of tephra cone. Udo tuff cone was constructed from Surtseyan eruption which went into with tephra finger jetting activities in the early stage, late interspersed with continuous uprush activities and proceeded to only continuous uprush activities in the last. When the enclosure of the vent by a long-lived tephra barrier would prevent the flooding and thus allow the vent to dry out, the Surtseyan eruption ceased to transmit into Strombolian activities, which constructed a cinder cone on the crater floor of the tuff cone. The Strombolian eruption ceased when magma in the conduit gradually became depleted in gas. In the case of Udo, the last magmatic activity was Hawaiian-type (and/or fountain) which accumulated basalt lava delta. And then the loose tephra of the tuff cone reworked over the moat lava and the northeastern flank.

• 한국환경농학회지
• /
• 제25권2호
• /
• pp.174-179
• /
• 2006

Chinese cabbage, Braccica campestris has long been consumed as a staple food for Koreans in various forms of fresh, salted, and fermented Kimchi. Cultivation of the crop under greenhouse has become a general practices to fulfill its off-seasonal consumer's demand. However, agricultural practices of the crop have always accompanied with heavy applications of pesticides caused by severe outbreaks of diseases and pose under warm and humid circumferences. Since dissipation patterns of pesticide residues in/on the crop under greenhouse conditions ate quite different from those in the open-air, changes of diazinon, O,O-diethyl O-2-isopropyl-6-methylpyrimidin-4-yl phosphornthioate, in/on the Chinese cabbage applied by foliar spraying under greenhouse were studied. Diazinon 34% EC was applied with dilution of recommended and double dose to the crop. The shoots of crop were harvested immediately after this application and at regular intervals over a 10-day. After sample preparations, the diazinon residue was analyzed using gas chromatography equipped with electron capture detector (GC/ECD). Initially deposited amount of the chemical in/on the crop right after applications with recommended and double doses were 8.3 and 15.2 mg/kg, respectively. The residue levels after 10 days of application were 0.03 and 0.09 mg/kg with 1.3 and 1.5 days of half-life in/on the crop, respectively. In consequent 10 days of pre-harvest interval (PHI) for diazinon EC formulation in/on Chinese cabbage under greenhouse condition was fulfill maximum residue level set by Korea Food and Drug Administration (KFDA, 0.1 mg/kg).

• 환경생물
• /
• 제37권4호
• /
• pp.526-534
• /
• 2019

Chlorella gloriosa (Chlorellaceae, Trebouxiophyceae) was isolated from seawater off the coast of the Dokdo Islands in Korea. An axenic culture was established using the streak-plate method on f/2 agar media supplemented with antibiotics, allowing identification of the isolate by morphological, molecular, and physiological analyses. The morphological characteristics observed by light and electron microscopy revealed typical morphologies of C. gloriosa species. The molecular phylogenetic inference drawn from the small-subunit 18S rRNA sequence verified that the microalgal strain belongs to C. gloriosa. Additionally, gas chromatography-mass spectrometry analysis showed that the isolate was rich in nutritionally important omega-3 and -6 polyunsaturated fatty acids and high-performance liquid chromatography analysis revealed that the high-value antioxidants lutein and violaxanthin were biosynthesized as accessory pigments by this microalga, with arabinose, galactose, and glucose as the major monosaccharides. Therefore, in this study, a Korean marine C. gloriosa species was discovered, characterized, and described, and subsequently added to the national culture collection.

• 에너지공학
• /
• 제2권1호
• /
• pp.54-67
• /
• 1993

CC1$_4$/CH$_4$/공기로 이루어진 예혼합 화염에 대한 2종류의 난류반응 모델을 Dow 케미칼사의 3차원 로타리 킬른 소각로에 적용하여 그 타당성을 확인하였다. 첫번째 난류반응 모델은 반응률이 반응물질의 난류혼합 속도에 지배된다는 fast chemistry 모델(모델 1)이고, 두번째 모델은 비평형 난류반응 모델(모델 2)로서 열량이 낮고 화염 억제 작용이 있는 산업폐기물인, CC1$_4$존재에 따른 반응감속을 연소속도 자료에 의해 고려한 모델이다. 수치해석의 결과에 의하면 CC1$_4$의 화염억제 작용을 적절히 고려한 두번째 비평형 난류반응 모델은 Dow 케미칼사 로타리 킬른의 출구에서 실험적으로 나타나는 농도 성층화 현상을 정성적으로 규명할 수 있었으며, CC1$_4$/CH$_4$몰비 변화에 따른 연소반응 지연 양상도 확인할 수 있었다. 기타 두 모델에 대한 비교 및 유동의 결과를 자세히 제시하였다.