• Steel and Composite Structures
• /
• 제37권6호
• /
• pp.695-709
• /
• 2020

The buckling properties of a single-layered graphene sheet (SLGS) are examined using nonlocal integral first shear deformation theory (FSDT) by incorporating the influence of visco-Pasternak's medium. This model contains only four variables, which is even less than the conventional FSDT. The visco-Pasternak's medium is introduced by considering the damping influence to the conventional foundation model which modeled by the linear Winkler's coefficient and Pasternak's (shear) foundation coefficient. The nanoplate under consideration is subjected to compressive in- plane edge loads per unit length. The impacts of many parameters such as scale parameter, aspect ratio, the visco-Pasternak's coefficients, damping parameter, and mode numbers on the stability investigation of the SLGSs are examined in detail. The obtained results are compared with the corresponding available in the literature.

• Steel and Composite Structures
• /
• 제41권6호
• /
• pp.787-803
• /
• 2021

The size-dependent nonlinear thermomechanical vibration analysis of pre- and post-buckled tapered two-directional functionally graded (2D-FG) microbeams is presented in this study. In the context of the modified couple stress theory, the formulations are derived based on the parabolic shear deformation beam theory and von Karman nonlinear strains. Different thermomechanical material properties are assumed to be temperature-dependent and smoothly vary in both length and thickness directions using the power law and the physical neutral axis concept is employed. The nonlinear governing equations are derived using the Hamilton principle and the resulting variable coefficient equations of motion are solved using the differential quadrature method (DQM) and iterative Newton's method for clamped-clamped and simply supported boundary conditions. Comparison studies are presented to validate the derived model and solution procedure. The impacts of induced thermal moments, temperature power index, two gradient indices, nonuniform cross-section, and microstructure length scale parameter on the frequency-temperature configurations are explored for both clamped and simply supported microbeams.

• 복합신소재구조학회 논문집
• /
• 제2권1호
• /
• pp.15-22
• /
• 2011

펄트루젼 FRP 구조용 부재는 많은 유용한 역학적, 물리적 성질 때문에 토목분야에서 구조부재의 매력적인 대체부재로 고려될 수 있다. 그러나 펄트루젼 FRP는 탄성계수가 상대적으로 낮고, 부재의 단면이 복부와 플렌지 등의 얇은 판요소로 구성되어 있기 때문에 압축재로 설계할 때 구조적인 안정성은 매우 중요한 고려사항이 된다. 따라서, 압축을 받는 구조용 부재의 설계를 위해, 판요소의 좌굴 및 후좌굴강도를 고려해야 한다. AISC/LRFD의 강구조 설계기준에서는, 후좌굴강도에 추가적인 단면 내 일정하지 않은 응력분포의 영향을 형상계수(form factor)를 사용하여 고려하고 있다. 이 논문에서는 압축력을 받는 펄트루젼 FRP 구조용 부재의 형상계수를 해석적으로 연구하였으며, 형상계수를 설정하는 과정에 대하여 제안하였다.

• Steel and Composite Structures
• /
• 제42권4호
• /
• pp.427-446
• /
• 2022

Cutouts in the beams or plates are often unavoidable due to inspection, maintenance, ventilation, structural aesthetics purpose, and sometimes to lighten the structures. Therefore, there will be a substantial reduction in the strength of the structure due to the introduction of the cutouts. However, these cutouts can be reinforced with the different patterns of ribs (stiffener) to enhance the strength of the structure. The present study highlights the influence of the elliptical cutout reinforced with a different pattern of ribs on the stability performance of such stiffened composite panels subjected to non-uniform edge loads by employing the Finite element (FE) technique. In the present formulation, a 9-noded heterosis element is used to model the skin, and a 3-noded isoparametric beam element is used to simulate the rib that is attached around a cutout in different patterns. The displacement compatibility condition is employed between the plate and stiffener, and arbitrary orientations are taken care by introducing respective transformation matrices. The effect of shear deformation and rotary inertia are incorporated in the formulation. A new mesh configuration is developed to house the attached ribs around an elliptical cutout with different patterns. Initially, a study is performed on the panels with different stiffener schemes for various ply orientations and for different stiffener depth to width ratios (d_s/b_s) to determine an optimal stiffener configuration. Further, various parametric studies are conducted on an obtained optimal stiffened panel to understand the effect of cutout size, cutout orientation, panel aspect ratio, and boundary conditions. Finally, from the analysis, it can be observed that the arrangement of the stiffener attached to a panel has a major impact on the buckling capacity of the stiffened panel. The stiffener's depth to width ratio also significantly influences the buckling characteristic.

• 한국도로학회논문집
• /
• 제18권6호
• /
• pp.41-50
• /
• 2016

OBJECTIVES : In this study, microstructural components of crumb rubber modified asphalt (CRMA) binder were investigated using environmental scanning electron microscope (ESEM). To clearly understand the elemental composition of the CRMA binder, energy dispersive X-ray spectroscopy (EDX) was employed on the ESEM samples. METHODS : CRMA binders were produced using open blade mixers at $177^{\circ}C$ for 30 min. The binders were artificially aged through a series of accelerated aging processes. Sample preparation was done by making a mold shape on the glass slide. Thereafter, the morphology of the CRMA binder was observed using the ESEM coupled with the EDX. RESULTS : The images captured from the ESEM indicate that the unaged CRMA binder appears to have a single-phase continuous nonuniform structure after the addition of crumb rubber particles, whereas the artificially aged CRMA binder was observed to have two different phases. ESEM coupled with EDX shows detailed internal structure of the modified binders compared to other technologies (i.e., optical microscopy, atomic force microscopy, and conventional scanning electron microscope). CONCLUSIONS : The captured images resemble the internal structures such as the viscous properties of the unaged CRMA binder and the interaction between the rubber particles and the base binder at aged condition. ESEM is a powerful instrument and with the introduction of EDX, it provided more details of the network microstructure of the asphalt binder. ESEM coupled with EDX is recommended for use in future investigation of microstructure of asphalt binders.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1367-1370
• /
• 2005

Microcellular foam processing of polymers requires a nucleated cell density greater than $10^9\;cells/cm^3$ so that the fully grown cells are smaller than 10 mm. A microcellular foam can be developed by first saturating a polymer sample with a volatile blowing agent, followed by rapidly decreasing its solubility in the polymer. In general, the cellular structure of crystalline polymer foams is difficult to control, compared to that of amorphous polymer foams. Since the gas does not dissolved in the crystallites, the polymer/gas solution formed during the microcellular processing is nonuniform. Moreover, the bubble nucleation is nonhomogeneous because of the heterogeneous nature of the crystalline polymer. In this paper, the effects of the crystallinity and morphology of crystalline polymers on the microcellular foam processing and on reflectivity of products are investigated. First, polymer specimens with various morphology and amount of solved blowing agent were prepared by varying the saturation pressure, saturation time and foaming condition. Then, cell morphologies according to several conditions were studied. The specimens with differing gas amount of solved and morphologies were foamed and their cellular structures were compared. The experimental results of reflectivity are compared to raw specimen and another specimen of different experimental conditions. After the experiments, recognize whether how reflectivity changes according to solved gas amount. And the effect of cell density and cell size on reflectivity is studied

• 한국세라믹학회지
• /
• 제42권8호
• /
• pp.554-560
• /
• 2005

The engineering ceramic needs the properties of high strength, hardness, corrosion-resistance and heat-resistance in order to withstand thermal shock or applied nonuniform stresses without failure. The densely coated porous ceramics can be used for machine component, electromagnetic component, bio-system component and energy-system component by their high-performances from superior coating properties and light-weight characteristics due to the structure including pore by itself. In this study we controlled the porosity of silica and alumina, $8.2\~25.4\%$ and $23.4\~36.0\%$, respectively, by the control of sintering temperature and starting powder size. We made bilayer structures, consisting of a transparent glass coating layer bonded to a thick substrate of different porous ceramics by a thin layer of epoxy adhesive, facilitated observations of crack initiation and propagation. The elastic modulus mismatch could be controlled using different porous ceramics as the substrate layer. Then we applied 150 N force using WC sphere with a radius of 3.18 mm by Hertzian indentation. As a result, the crack initiation in the coating layer was delayed at lower porosity in the substrate layer, and the damage in the coating layer was relatively smaller at the bilayer structure coated on higher elastic substrate.

• 한국전자파학회논문지
• /
• 제11권3호
• /
• pp.388-402
• /
• 2000

주기적인 구형격자를 갖는 유전체 코팅된 도체 실린더에 대해 무한 주기 구조와 유한 주기 구조에 대한 누설 파 안테나의 복사 특성을 이론적으로 해석하였다. 무한 주기 구조에 대하여는 모드 정합 법을 적용하여 해석하 였고, 유한 주기 구조에 대하여는 퓨리에 변환과 모드 전개를 사용하여 적분 방정식을 유도하고 선형 연립 방정 식을 얻는다. 구형격자의 폭, 깊이, 유전체 코팅두께, 도체 실린더의 반경, 유한 구형격자 개수의 영향이 위상 상 수, 누설 상수 및 복사패턴 등과 복사 특성에 미치는 영향을 조사하였고, 유한 주기 구조와 무한 주기 구조의 결 과를 비교하고 잘 일치함을 확인할 수 있었다. 균일 유한 주기 구형격자에 의한 높은 측엽을 줄이기 위해 안테나 의 전후단 부에 테이퍼링과 비균일 준주기 슬롯배열을 고려하였다. 또한 구형격자 표면파 안테나에 사용되는 구 형격자 주기. 폭, 깊이에 대해 테이퍼링을 통해 낮은 측엽을 갖는 endfire 복사패턴을 얻을 수 있었다.

• 대한조선학회지
• /
• 제27권4호
• /
• pp.51-57
• /
• 1990

구조물을 용접할 시에는 열전도에 따른 온도 분포의 불균일에 의해 구조물에서 잔류 응력 및 변형이 발생되게 된다. 열전도에 따른 구조물의 거동을 기술하기 위해서는 열탄소성해석이 필요하게 되는데, 본 연구에서는 1차원 적층보 이론을 이용해서 보의 변형 및 잔류 응력을 계산하였다. 기존의 1차원 열탄소성 해석에서는 용접 길이가 무한해야만 성립하는 평형조건을 이용하고 있고, 경계 조건이 적절히 반영되지 못하는 제한성이 있었다. 그러나 증분 유한 요소법에 기초한 적층보 이론은 이런 제한성을 극복할 수 있다. 2차원 열탄소성 해석에서는 자유도의 증가에 따라 계산 시간이 방대해 지고, 변형 계산시에는 부정확성이 있는데에 비하여 적층보 해석에서는 2차원 해석과 같이 보 깊이 방향의 재료 성질 변화도 고려할 수 있고, 2차원 해석에 비해 자유도가 대폭 감소되었으며, 변형 계산에서도 실험치와 잘 부합되고 있다.

• 한국추진공학회지
• /
• 제2권1호
• /
• pp.31-40
• /
• 1998

고강도 알루미늄 대형 링롤재의 급냉 및 요소제거 후 발생하는 잔류응력을 2차원 및 3차원 유한요소 해석하였고, 3단계 절단법에 의해 측정된 변형율과 ABAQUS의 요소제거 기능을 이용한 해석값을 직접 비교하였다. 급냉후 잔류응력 해석결과는 2단 과시효후 측정값과 비슷한 경향을 보였으나 그 절대값의 차이가 크게 나타났다. 이는 링 시편의 높이가 작아 측정값이 부정확하였기 때문이며, 링의 높이를 증가시켜 높이방향으로 균일한 응력분포를 갖도록 하면 그 차이가 감소될 것으로 판단된다. 잔류응력을 측정하는 3단계 절단 과정을 모사한 3차원 해석결과와 측정된 변형율을 직접 비교함으로써 실험과 해석의 정확성을 향상시킬 수 있도록 하였다. 이로부터 잔류응력이 내재하고 형상이 복잡한 대형 알루미늄 구조물의 기계가 공에 의한 변형을 정확히 예측할 수 있는 기반을 마련하였다.