• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.262-266
• /
• 2014

Military vehicle equipped with an antenna and a shelter for operating radar has a vibration exposure during driving time. This vibration would have influence on structure of military vehicle critically. In this paper, driving stability of the military vehicle is obtained through the vibration response analysis. And, vibration level of the military vehicle satisfied the military vibration specification through analysis and comparing the MIL-STD-810G. PSD and Grms data obtained by road test can be used for vibration test specification of cabinets and electronic equipment in shelter.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.1
• /
• pp.25-34
• /
• 2003

Gas insulated switchgear(GIS) is an important equipment in a substation. It is highly desirable to measure a partial discharge(PD) in GIS which is a symptom before insulation breakdown occurs. The issue is that the PD signal is weak and sensitive to external noise. In this paper, the algorithm for detection of PD in GIS using wavelet transform is proposed. The wavelet transform provides a direct quantitative measure of spectral content, "dynamic spectrum", in the time-frequency domain. The recommended mother wavelet is 'Daubechies' wavelet. 'db4', the most commonly applied mother wavelet in the power quality analysis, can be used most properly in disturbance phenomena which occurs rapidly for a short time. Through the procedure of wavelet transform, noise extraction and reconstruction, the signal is Analyzed to determine the magnitude of PD in GIS. In experimental results, we can know that partial discharge is exactly detected in combination of Dl and D2 using wavelet transform.transform.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.392-398
• /
• 1986

It is often occurred that exhaust pipe of an internal combustion engine should be bent due to some geometrical constraints. Especially for automobiles most of exhaust pipes of engines have curvature to avoid rear axles. In this paper effects of pipe curvature on the exhaust noise of a diesel engine have been studied experimentally. Experiments were carried out on a 4-cycle, 2164cc diesel engine. Two types of curvature, circular arc and retangle, were tested. Sound pressure level (SPL) and power spectrum of the exhaust noise were measured by inserting bent pipes of different curvature dimensions into the exhaust pipe at various engine operating conditions. The following results were obtained from this study. Among the engine operating conditions the exhaust noise was affected mainly by engine revolution speed. The noise was reduced by the circular arc bent pipe. The effectiveness of an arc bent pipe on the noise reduction was dominated by its arc angle and the maximum noise reduction was obtained by the angle of 180.deg.. But the noise reduction could not be obtained by the rectangular bent pipe, and at high engine speed the noise was rather increased due to turbulence of exhaust gas.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.2
• /
• pp.113-119
• /
• 2020

Motor noise is a major concern in order to improve perceptual feeling of car interior sound due to increased motor usage in passenger cars. The purpose of this study is to propose factors that can represent the acoustic performance of motor noise according to the change of load. To this end, at first, it is shown that power spectrum and total loudness are not fit for noise performance, and then, PN_B, partial loudness related to the brush friction component, and PN_R, partial loudness related to the torque ripple component are investigated as factors representing motor noise. The performance curve of motor noise using PN_B and PN_R is proposed to identify trends of motor noise according to the loads. The curve could be a guide for the noise control, the selection of motor, and the improvement of a system.

• Journal of radiological science and technology
• /
• v.29 no.4
• /
• pp.237-240
• /
• 2006

The Noise of CR Systems is made up of X-ray quantum mottle and additional Imaging plate's structure noise, photon noise of lumine cence, noise of electrometer, quantization noise etc. In this Regius 150 system, SNR was increased from 8.2 to 30 with linearily according to radiation dose from 0.1 mR to 100 mR. It means that the Regius 150 system has enough trustability because of SNR is over 5 by Rose Model. NPS was calculated two dementional Fourier Transform with shake of pixel value in the white Image. In the spatial frequence range of $0.5\;lp/mm{\sim}2.5\;lp/mm$, the NPS was distributed $10^{-4}{\sim}10^{-5}$ at 1 mR X-ray dose. That is similar result compare other systems to that of Kodak CR system reported by Carlu, HR-CR system reported by Dobbins.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.3A
• /
• pp.272-280
• /
• 2009

Measurement of the background radio noise is very important process being used in survey of radio noise environment, calculating the threshold level for the frequency occupancy measurement and so forth. First step of background radio noise measurement is to select the sample sub-band which is mostly dominated by the background white Gaussian noise (WGN) within the target band. The second step is to carry out the main measurement of radio noise on this selected sample sub-band for the representative value of the noise power. In this paper, a method for selection of sample sub-band for the effective background radio noise measurement using SVD is proposed under the assumption that background radio noise is WGN. The performance of the proposed method is compared with that of the APD method which is widely used for the same purpose. Simulation results are shown to demonstrate the high performance of the proposed method in comparison with the existing APD method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.2
• /
• pp.251-256
• /
• 2001

An error probability analysis is performed far a hybrid DS/SFH spread-spectrum system using minimum shift keying(MSK) modulation. The channel is assumed to be a Rayleigh fading channel with partial-band noise interference. Expressions are derived for the bit error rate(BER) in the context of Rician and Rayleigh fading channels, as a function of the average signal-to-noise ratio(SNR) $E_b/N_0$, the average signal-to- interference ratio(SJR) $E_b/N_J$, and channel parameters. As a result, in the fading channel with large Rician factor, K, which denotes the ratio of power of the direct and the diffused components, the partial-band interference is the worst case. On the other hand, in Rayleigh fading channel(K=0), the full-band interference($\rho$=1) brings the system to the worst case. Performance comparisons among various channels show that the factor K has much large effect on overall performance. For example, in conditions of $\rho$=0.1 and BER=$10^-2$, the system in Rician channel with K=10 requires more 1.9 dB SNR than that in AWGN channel, whereas it is less 5 dB SNR than that in the Rayleigh channel with K=0.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.10
• /
• pp.43-47
• /
• 2002

A simple optical signal to noise ratio monitoring method using fiber Bragg grating is proposed for monitoring performance of OADM. OSNR of each channel is determined by monitoring the optical power transmitted and reflected from fiber Bragg gratings, simultaneously. We have obtained OSNR with accuracy better than 0.8㏈ compared with OSA of 0.1nm optical resolution in the wide input power range between -6 ㏈m and -23㏈m per channel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.906-911
• /
• 2001

In this paper, LPI(low probability of intercept) and AJ(anti jamming) performance of the chirped BPSK system are analyzed. In the chirp method the cyclostationary of the signal is eliminated, since the instantaneous frequency is varied randomly within the whole spread bandwidth. Therefore, chirp method is considered for good LPI system against DAM(delay-and-multiplier) or SC (squaring circuit) interceptor which detects the chip rate or carrier frequency. Longer chirp duration makes the LPI performance better. From the simulation results, the chirp method has better AJ performance than DS(direct sequence) system in the PBNJ(partial band noise jammer) channel. At the same JSR(jammer to signal power ratio) level, chirped BPSK system has more robust AJ performance against MTJ(multi-tone jammer) than PBNJ.

• KIEE International Transactions on Power Engineering
• /
• v.3A no.4
• /
• pp.214-221
• /
• 2003

In view of the fact that gas insulated switchgear (GIS) is an important piece of equipment in a substation, it is highly desirable to continuously monitor the state of equipment by measuring the partial discharge (PD) activity in a GIS, as PD is a symptom of an insulation weakness/breakdown. However, since the PD signal is relatively weak and the external noise makes detection of the PD signal difficult, it therefore requires careful attention in its detection. In this paper, the algorithm for detection of PD in the GIS using the wavelet transform (WT) is proposed. The WT provides a direct quantitative measure of the spectral content and dynamic spectrum in the time-frequency domain. The most appropriate mother wavelet for this application is the Daubechies 4 (db4) wavelet. 'db4', the most commonly applied mother wavelet in the power quality analysis, is very well suited to detecting high frequency signals of very short duration, such as those associated with the PD phenomenon. The proposed algorithm is based on utilizing the absolute sum value of coefficients, which are a combination of D1 (Detail 1) and D2 (Detail 2) in multiresolution signal decomposition (MSD) based on WT after noise elimination and normalization.