• The KIPS Transactions:PartC
• /
• v.13C no.1 s.104
• /
• pp.83-94
• /
• 2006

This paper describes ATM cell encipherment method using Rijndael Algorithm adopted as an AES(Advanced Encryption Standard) by NIST in 2001. ISO 9160 describes the requirement of physical layer data processing in encryption/decryption. For the description of ATM cell encipherment method, we implemented ATM data encipherment equipment which satisfies the requirements of ISO 9160, and verified the encipherment/decipherment processing at ATM STM-1 rate(155.52Mbps). The DES algorithm can process data in the block size of 64 bits and its key length is 64 bits, but the Rijndael algorithm can process data in the block size of 128 bits and the key length of 128, 192, or 256 bits selectively. So it is more flexible in high bit rate data processing and stronger in encription strength than DES. For tile real time encryption of high bit rate data stream. Rijndael algorithm was implemented in FPGA in this experiment. The boundary of serial UNI cell was detected by the CRC method, and in the case of user data cell the payload of 48 octets (384 bits) is converted in parallel and transferred to 3 Rijndael encipherment module in the block size of 128 bits individually. After completion of encryption, the header stored in buffer is attached to the enciphered payload and retransmitted in the format of cell. At the receiving end, the boundary of ceil is detected by the CRC method and the payload type is decided. n the payload type is the user data cell, the payload of the cell is transferred to the 3-Rijndael decryption module in the block sire of 128 bits for decryption of data. And in the case of maintenance cell, the payload is extracted without decryption processing.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.138-142
• /
• 2004

In this paper, we present a new method for monitoring of ECU's sensor signals of vehicle. In order to measure the ECU's sensor signals, the interfaced circuit is designed to communicate ECU and the Embedded Linux is used to monitor communication result through Web the Embedded Linux system and this system is said "ECU Interface Part". In ECU Interface Part the interface circuit is designed to match voltage level between ECU and SA-1110 micro controller and interface circuit to communicate ECU according to the ISO, SAE communication protocol standard. Because Embedded Linux does not allow to access hardware directly in application level, anyone who wants to modify any low level hardware must develop device driver. To monitor ECU's sensor signals the most important thing is to match serial level between ECU and ECU Interface Part. It means to communicate correctly between two hardware we need to match voltage and signal level, and need to match baudrate. The voltage of SA-1110 is 0 ${\sim}$ +3.3V and ECU is 0 ${\sim}$ +12V and, ECU's communication Line K does multiple operation so, the interface circuit is used to match voltage and signal level. In Addition to ECU's baudrate is 10400bps, it's not standard baudrate in computer environment. So, we need to develop a device driver to control the interface circuit, and change baudrate. To monitor ECU's sensor signals through web there's a network socket program is working in Embedded Linux. It works as server program and manages user's connections and commands. Anyone who wants to monitor ECU's sensor signals he just only connect to Embedded Linux system with web browser then, Embedded Linux webserver will return the ActiveX webbased measurement software. It works in web browser and inits ECU, as a result it returns sensor signals through web. All the programs are developed with GCC(GNU C Compiler) and, webbased measurement software is developed with Borland C++ Builder.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.6
• /
• pp.329-336
• /
• 2016

In the outdoor advertising and industrial sites, are trying to implement the LED electric bulletin board system that is based on image processing in order to express a variety of intention in real time. Recently, in various field, rather than simple text representation, the importance of intuitive communication using images is increasing. Thus, instead of outputting the simple input information for communication, a system that can output a real-time information being sought. Therefore, the system is directed to overcoming by converting the problem of mapping an image on a variety of conventional LED display that can not be output images, the possible image output formats. Using an LED of low power, it has developed to output the efficient messages and images within a limited resources. This paper provides a system capable of managing the LED display on the wireless network. Atmega2560, Wi-Fi module, using the server and Android applications client, rather than printing a text only, it is a system to reduce the load generated image output character output in to the conversion process as can be managed by the server.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.443-446
• /
• 2003

This paper implement Remote Meter Reading System which is used Bluetooth and SMS in CDMA. This System propose system which tan detect a total amount of gas, electricity or water without a meterman, at home BlueTooth is a close range wireless communication technology which uses a wireless frequency 2.4GHz and has a high trust and self error correction technology according to a low power consumption quality and a high-speed frequency hopping. This makes get a high trust concerning a data transmission than an existing modem. In addition, though wireless modem is restricted by a minimal of a wireless terminal, it will be possible to coincide with the function of the portable with the low power consumption quality by using Bluetooth. And as the system on a chip of module progresses, the possibility of the small size is present. Nowadays, SMS Protocol in CDMA for have a network function based on PPP in CDMA Phone. The proposed Remote Meter Reading System to get more nobility, efficiency, and have good function. SMS Protocol in CDMA have profits which is low power, low cost, and low microwave output.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.262-269
• /
• 2020

Recently, many attempts have been made to reduce the time required for payment in various shopping environments. In addition, for the Fourth Industrial Revolution era, artificial intelligence is advancing, and Internet of Things (IoT) devices are becoming more compact and cheaper. So, by integrating these two technologies, access to building an unmanned environment to save people time has become easier. In this paper, we propose a smart shopping cart system based on low-cost IoT equipment and deep-learning object-detection technology. The proposed smart cart system consists of a camera for real-time product detection, an ultrasonic sensor that acts as a trigger, a weight sensor to determine whether a product is put into or taken out of the shopping cart, an application for smartphones that provides a user interface for a virtual shopping cart, and a deep learning server where learned product data are stored. Communication between each module is through Transmission Control Protocol/Internet Protocol, a Hypertext Transmission Protocol network, a You Only Look Once darknet library, and an object detection system used by the server to recognize products. The user can check a list of items put into the smart cart via the smartphone app, and can automatically pay for them. The smart cart system proposed in this paper can be applied to unmanned stores with high cost-effectiveness.

• Annual Conference of KIPS
• /
• 2003.11a
• /
• pp.115-118
• /
• 2003

최근 MOM 기술은 비즈니스 로직을 수행하는 애플리케이션 서버의 필수적인 구성요소로서 자리잡고 있으며, 보통 수백에서 수천의 클라이언트 요청을 처리할 수 있는 능력을 제공한다. MOM 은 이러한 대용량의 클라이언트 요청을 효과적으로 처리하기 위해서 효율적이고 확장성있는(스케일러블) 네트워크 모듈이 필요하며, 다양한 네트워크 프로토콜을 지원해야 한다. MOM이 기본적으로 지원하는 메시징 기능은 PTP(Point-To-Point)와 publish/subscribe 메시징 도메인으로 나뉘는데 이 논문에서는 두 가지 메시징 도메인과 그룹통신 메시징 서비스 기능을 동시에 지원하는 MoIM-Message 시스템의 하부 통신 모듈의 설계에 대해 기술한다. PTP와 publish/subscribe 메시징을 지원하기 위해 세가지 프리미티브 메시징 오퍼레이션인 "synchronous send", "synchronous receive", "asynchronous receive"를 정의하였으며 하부 통신 모듈 역할을 하는 메시지 트랜스포트 관리 계층내의 트랜스포트 관리자 내에 구현되었다. 트랜스포트 관리자는 다양한 트랜스포트 프로토콜을 적용할 수 있도록 하기 위해 트랜스포트 어댑터로 설계되었으며, 대량의 통신 요청을 효과적으로 처리하기 위해 "polling with multiple service thread model" 기법을 적용하여 구현되었다. 또한, 모바일 클라이언트 환경을 지원하기 위해 클라이언트 측 통신 모듈을 IPaq PDA 상에 포팅하였다. 본 논문에서 제안하는 세 가지 프리미티브 메시징 오퍼레이션을 제공하는 통신 모듈은 MOM이 기본적으로 지원해야 할 메시징 도메인과 대용량의 클라이언트 요청을 효율적으로 처리할 수 있는 구조를 가진다.es}8$ 모드를 모두 사용한 경우와 $8{\times}8$ 단일모드를 사용한 경우보다 계산 시간이 감소하였음을 확인하였다.행중인 MoIM-Messge서버의 네트워크 모듈로 다중 쓰레드 소켓폴링 모델을 적용하였다.n rate compared with conventional face recognition algorithms. 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유의성이 움직임 보정 전에 비하여 낮음을 알 수 있었다. 결론: 뇌활성화 과제 수행시에 동반되는 피험자의 머리 움직임에 의하여 도파민 유리가 과대평가되었으며 이는 이 연구에서 제안한 영상정합을 이용한 움직임 보정기법에

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.46 no.1
• /
• pp.88-95
• /
• 2009

This paper presents a traffic pattern matching hardware that can be used in high performance network applications. The presented hardware is designed for a contents security system which is to block various kinds of information drain or intrusion activities. The hardware consists of two parts: the header lookup and string pattern matching parts. For implementing the header lookup part in hardware, the TCAMs(ternary CAMs) are popularly used. Since the TCAM approach is inefficient in terms of the hardware and memory costs and the power consumption, however, we adopt and modify an alternative approach based on the comparator arrays and the HiCuts tree. Our implementation results, using Xilinx FPGA XC4VSX55, show that our design can reduce the usage of the FPGA slices by about 26%, and the Block RAM by about 58%. In the design of string pattern matching part, we design and use a hashing module based on cellular automata, which is hardware efficient and consumes less power by adaptively changing its configuration to reduce the collision rates.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.292-295
• /
• 2003

This paper presents the architecture and its function of Tool server. MPEG-21 will enable all-electronic creation, delivery and trade of digital multimedia content and transparent usage of various content types on network device. Therefore, we can provide access to information and services from almost anywhere at anytime with various terminals and networks. In order to support multimedia delivery chain that contains content creation, production, delivery and consumption, we need some elements to identify, describe, manage and protect the contents. Thus, we define Digital Item Processing(DIP), Digital Item Adaptation(DIA) server and Tool server as primary objects of MPEG-21 multimedia framework. DIP provides a function which creates and consumes Digital Item(DI) as a kind of a digital object by user. DIA server adapts the original DI to the usage environment description sent from the terminal and transmits the adapted DI to the terminal. Tool sewer searches for a tool requested from DIP or DIA and downloads the best tool to DIP or DIA server. In this paper, we present how Tool server is organized and is used among 2 primary objects. The paper is structured as following: Section 1 briefly describes why MPEG-21 is needed and what MPEG-21 wants. We see the basic architecture of tool server and its functionality by each module in section 2. Section 3 explains a scenario that tool server transmits tool to DIP or DIA. The paper concludes in section 4.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1167-1174
• /
• 2009

In the monitoring of a patient in a sickroom, not only the physiologic and environmental data of the patient, which is automatically measured, but also the clinical data(clinical chart)of the patient, which is drew up by a doctor or nurse, are recognized as important data. However, since in the current environment of a sickroom, clinical data is collected being divided from the data that is automatically measured, the two data are used without an effective integration. This is because the integration of the two data is difficult due to their different collection times, which leads the reconstruction of clinical data to be remarkably uncertain. In order to solve these problems, a method to synchronize the continuous environmental data of a sickroom and clinical data is appearing as an important measure. In addition, the increase of use of small machines and the development of solutions based on wireless communications provide a communication platform to the developers of health care. Thus, this paper realizes a remote system for taking care of patients based on a web that uses mobile phones. That is, clinical data made by a nurse or doctor and the environmental data of a sick room comes to be collected by a collection module through a wireless sensor network. An observer can see clinical data and the environmental data of a sickroom through his/her mobile phone, integrating and storing his/her data into the database. Families of a patient can see clinical data made by hospital and the environment of the sick room of the patent through their computers or mobile phones outside the hospital. Through the system,hospital can provide better medical services to patients and their families.

• Journal of Korea Water Resources Association
• /
• v.43 no.11
• /
• pp.995-1009
• /
• 2010

Accelerated soil erosion due to extreme climate change, such as increased rainfall intensity, and human-induced environmental changes, is a widely recognized problem. Existing soil erosion models are generally based on the gross erosion concept to compute annual upland soil loss in tons per acre per year. However, such models are not suitable for event-based simulations of erosion and deposition in time and space. Recent advances in computer geographic information system (GIS) technologies have allowed hydrologists to develop physically based models, and the trend in erosion prediction is towards process-based models, instead of conceptually lumped models. This study aims to propose an effective and robust distributed rainfall-sediment yield-runoff model consisting of basic element modules: a rainfall-runoff module based on the kinematic wave method for subsurface and surface flow, and a runoff-sediment yield-runoff model based on the unit stream power method. The model was tested on the Cheoncheon catchment, upstream of the Yongdam dam using hydrological data for three extreme flood events due to typhoons. The model provided acceptable simulation results with respect to both discharge and sediment discharge even though the simulated sedigraphs were underestimated, compared to observations. The spatial distribution of erosion and deposition demonstrated that eroded sediment loads were deposited in the cells along the channel network, which have a short overland flow length and a gentle local slope while the erosion rate increased as rainfall became larger. Additionally, spatially heterogeneous rainfall intensity, dependant on Thiessen polygons, led to spatially-distinct erosion and deposition patterns.