• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.26-30
• /
• 2008

This study was designed to investigate the effect of hybridization of synthetic/natural materials for annulus fibrosus (AF) tissue regeneration in vitro and in vivo. The synthetic/natural hybrid scaffolds were prepared using PLGA (poly (lactic-co-glycolic) acid), SIS (small intestinal submucosa) and DBP (demineralized bone particles). PLGA, PLGA/SIS(20%), PLGA/DBP(20%) and PLGA/SIS (10%)/DBP (10%) scaffold were manufactured by solvent casting/salt leaching method. Compressive strength was measured. Rabbit AF cells were isolated, cultured and seeded into experimental groups. Hydroxyproline production and DNA quantity of AP cells on each scaffold was measured at 2, 4 and 6 weeks after in vitro culture. Cell-scaffold composites were implanted subcutaneously into athymic mice. After 1,4 and 6 weeks postoperatively, specimens were taken and H&E, Safranin-O and type I collagen staining were carried out concerning formation of cartilagenous tissue. In vitro PLGA/SIS scaffold was evaluated for total collagen content (bydroryproline/DNA content) and PLGA scaffold was evaluated for compressive strength.

• Elastomers and Composites
• /
• v.21 no.1
• /
• pp.13-19
• /
• 1986

The effects of several vulcanizing accelerators on the determination of kinetic parameters of natural rubber vulcanizate was studied by DSC. Kinetic parameters were determined by means of the calculation procedures of Borchardt-Daniels and Oscillating Disk Rheometer (ODR) cure curve analysis, using both DSC exothermal thermogram and ODR cure curve. In order to examine the credibility in the DSC method the same compound which was und for DSC method was used for the comparison with the results of ODR data. Upon this method, kinetic rate constant (k), and Arrehenius parameter (Ea, ko, n) have been determined for rubber compounds via a new method using DSC thermogram and ODR cure curve. In the comparison of DSC and ODR results, kinetic parameters has shown good agreements between two results. Consequently, from the present studies, it is shown that the DSC thermoanalytical method can provide an alternate new method of kinetic study of rubber vulcanization.

• Composites Research
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2019

Recently, according to environmental regulations, the automobile industry has been conducting various research on the use of composite materials to increase fuel efficiency. However, there has not been much research on lightweight chassis components. Therefore, in this research, the purpose of this study is to apply composite materials to the sub-frame of chassis components to achieve equivalent levels of stiffness, strength, NVH performance and 50% lightweight compared to the steel sub-frame. First, the Natural frequency of steel and composite specimens was compared to the damping characteristics of composite materials. Then, in this study, the Lay-up Sequence was derived to maximize the stiffness and strength of the sub-frame by applying composite materials. And this lay-up Sequence is proposed to avoid heat shrinkage due to curing during manufacturing. This process was designed based on a FEM structural analysis, and a Natural frequency and frequency response function graph was confirmed based on a modal analysis. The prototype type composite sub-frame was manufactured based on the design and the F.E.M analysis was verified through a modal experiment. Furthermore, it was fitted to the actual vehicle to verify the natural frequency and the indoor noise vibration response, including idling and road noise. This result was confirmed to be equivalent to the steel sub-frame. Finally, the composite sub-frame weight was confirmed to be about 50% of the steel sub-frame.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.149-157
• /
• 2017

As the amount of construction wastes increase, reuse of recycled materials is being considered in research areas. While there are many experimental investigations focusing on development of mortar and concrete using the recycled materials, the studies regarding the fiber-reinforced cement composites (FRCCs) using recycled materials are still limited. In this paper, an experimental attempt has been made to investigate the effect of recycled fine aggregates and fly ash on the mechanical properties of PVA FRCCs. The cement and natural sand were respectively replaced by fly ash and recycled fine aggregates at two content levels, 25% and 50%. Ten types of PVA FRCCs mixes were fabricated and tested to investigate the flexural, compressive and direct tensile behaviors. The test results show that flexural, compressive and direct tensile strength were decreased with increase in fly ash content at all ages. In particular, flexural, compressive and direct tensile strengths of specimens, containing 50% recycled fine aggregates and 50% fly ash, showed the lowest values. The modulus of elasticity of specimens showed similar trend to the 28-day compressive strength. Poisson's ratio was increased with increase in fly ash and recycled fine aggregates content.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.2
• /
• pp.143-148
• /
• 2011

In this work, a composite formed by adding loess with lanthanium ("La-Loess") was proposed for effective removal of phosphate found in confined water bodies such as lake and reservoir. It was found that the theoretical maximum amount of lanthanum that can be attached to Loess was 2.68 mg La/g Loess. The phosphate removal was enhanced as an added amount of La-Loess composite increased. Furthermore, there was a noticeable difference in phosphate removal between Loess and La-Loess as the latter required 1.5 to 10 times less Loess than the former. Both Isotherm equations of Freundlich and Langmuir can be used to explain the phosphate adsorption characteristics in using La-Loess composites. The phosphate removal was very effective in the pH range of 5~8, which means that the proposed adsorbent can be directly applied to natural water without adjusting pH. Also, the La-Loess composites were well settled within 30 min without causing turbidity in water. Consequently, the proposed La-Loess can be strongly recommended for phosphate removal in confined water bodies.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.81-90
• /
• 2003

In this study, we investigated the weathering properties of Korean Rhus lacquers containing tung oil and their potential use as exterior coatings. The finished lacquers were prepared with a raw Korean Rhus lacquer or refined Korean Rhus lacquer content of 10, 20, 30 and 40 wt.% (corresponding to ratios of 10/90, 20/80, 30/70 and 40/60 by weight of Korean Rhus lacquer/tung oil, respectively). The curing temperature of the prepared lacquer increased with increasing the content of the raw Korean Rhus lacquer. This increased curing temperature is related to higher proportion of hydroxyl groups in the prepared lacquer, due to the content of the raw Korean Rhus lacquer. In accelerated weathering testing, the changes in the gloss and contact angle of the prepared lacquers showed a similar trend to that of traditional exterior oil stain. In addition, the prepared lacquers containing tung oil showed greater discoloration than traditional exterior oil stain. However, the discoloration of the prepared lacquer with a raw Korean Rhus lacquer content of 40 wt.%, and that of the prepared lacquer with refined Korean Rhus lacquer contents of 30 wt.% and 40 wt.%, showed a similar trend to that of traditional exterior oil stain. Consequentially, these prepared lacquers showed a potential for being used as exterior coatings.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.38-45
• /
• 2000

Influence of rubber composition on migration of antiozonants to the surface in ternary rubber-based vulcanizates composed of natural rubber (NR) styrene-butadiene rubber (SBR), and butadiene rubber (BR) was studied. Of the three rubbers, contents of two rudders were same and only the other one content was different (variable rubber) IPPD and HPPD were employed as antiozonants. Migration experiments were performed at $60^{\circ}C$ for 21 days and outdoors for 4 months. Migration rates of the antiozonants increase by increasing the content ratio of the variable rubber in the vulcanizares from NR/SBR/BR=1/1/0.2 to 1/1/1 and then decrease with an increase of the content ratio of the variable rudder from 1/1/1 to 1/1/5. Migration behaviors of the antiozonants in the ternary rudder-based vulcanizates depending on the rubber composition were explained by the intermolecular interactions between rubber and antiozonant, by the solubility difference of the antiozonants for the rubbers, and by the interface formed between dissimilar rubbers in the triblends.

• Journal of Aerospace System Engineering
• /
• v.13 no.6
• /
• pp.52-59
• /
• 2019

The rotor blade is a key component that generates the lift, thrust, and control forces required for helicopter flight by the torque transmitted through the hub and the blade pitch angle control, and should be designed to factor vibration characteristics so that there is no risk of resonance with structural safety. In this study, the structural design of the main rotor blade for MPUH(Multi-Purpose Unmanned Helicopter) was conducted and the sectional stiffness measurement of the fabricated blade was performed. The evaluation of the vibration characteristics of the main rotor system was then conducted factoring the measured stiffness distribution. The interior of the rotor blade comprised of the skin, spar, and torsion box, and carbon and glass fiber composites were applied. The Ksec2D program was applied to predict the stiffness of blade, and the results were compared to the measured data. CAMRADII, a comprehensive rotorcraft analysis program, was applied to investigate the natural frequency trends and resonance risks due to the rotor rotation.

• Wind and Structures
• /
• v.27 no.4
• /
• pp.269-282
• /
• 2018

In this paper, a new displacement field based on quasi-3D hybrid-type higher order shear deformation theory is developed to analyze the static and dynamic response of exponential (E), power-law (P) and sigmoïd (S) functionally graded beams. Novelty of this theory is that involve just three unknowns with including stretching effect, as opposed to four or even greater numbers in other shear and normal deformation theories. It also accounts for a parabolic distribution of the transverse shear stresses across the thickness, and satisfies the zero traction boundary conditions at beams surfaces without introducing a shear correction factor. The beam governing equations and boundary conditions are determined by employing the Hamilton's principle. Navier-type analytical solutions of bending and free vibration analysis are provided for simply supported beams subjected to uniform distribution loads. The effect of the sigmoid, exponent and power-law volume fraction, the thickness stretching and the material length scale parameter on the deflection, stresses and natural frequencies are discussed in tabular and graphical forms. The obtained results are compared with previously published results to verify the performance of this theory. It was clearly shown that this theory is not only accurate and efficient but almost comparable to other higher order shear deformation theories that contain more number of unknowns.

• Journal of Ecology and Environment
• /
• v.43 no.2
• /
• pp.129-160
• /
• 2019

Background: Characterizing and describing soils and land use and make a suggestion for sustainable utilization of land resources in the Ethiopian Rift valley flat plain areas of Lake Chamo Sub-Basin (CSB) are essential. Objectives: To (1) characterize soils of experimental area according to World Reference Base Legend and assess the nature and extent of salinity problems; (2) characterize land use systems and their role in soil properties; and (3) identify best land use practices used for both environmental management and improve agricultural productivity. Methods: Twelve randomly collected soil samples were prepared from the above land uses into 120 composites and analyzed. Results: Organic carbon (OC) and total nitrogen (TN) were varied along different land uses and depleted from the surface soils. The soil units include Chernozems (41.67%), Kastanozems (25%), Solonchaks (16.67%), and Cambisols (16.67%). The identified land uses are annual crops (AA), perennial crops (PA), and natural forest (NF). Generally, organic carbon, total nitrogen, percentage base saturation (PBS), exchangeable (potassium, calcium, and magnesium), available phosphorus (P₂O₅), manganese, copper, and iron contents were decreased in cultivated soils. Soil salinity problem was observed in annuals. Annuals have less nutrient content compared to perennials in irrigated agriculture while it is greater in annuals under rainfed. Clay, total nitrogen, available phosphorus, and available potassium (K₂O) contents were correlated positively and highly significantly with organic carbon and electrical conductivity. Conclusion: Management practices that improve soil quality should be integrated with leguminous crops when the land is used for annual crops production.