• Korean Journal of Materials Research
• /
• v.10 no.4
• /
• pp.257-263
• /
• 2000

Thermoelectric properties of the 0.05wt% $SbI_3$-doped n-type $Bi_2(Te_{0.95}Se_{0.05})_3$ alloy, prepared by melting/grinding and hot pressing, were investigated with variation of the annealing time up to 36 hours. The electron concentration of the 0.05wt% SbI$_3$-doped n-type $Bi_2(Te_{0.95}Se_{0.05})_3$ alloy decreased with increasing the annealing time. The figure-of-merit of the 0.05wt% $SbI_3$-doped n-type $Bi_2(Te_{0.95}Se_{0.05})_3$ alloy was improved from $2.1{\times}10^{-3}/K$ to $2.35{\times}10^{-3}/K$ by annealing at $500^{\circ}C$ for 3 hours. When annealed longer than 12 hours, however, the figure-of-merit decreased substantially due to the increase of the electrical resistivity.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.69-76
• /
• 1997

P-type ($Bi_{0.5}Sb_{1.5}Te_3$) and n-type ($Bi_2Te_{2.4} Se_{0.6}$) thermoelectric thin film were deposited on glass and Teflon substrates by the flash evaporation technique. The changes in thermoelectric properties, such as Seebeck coefficient, electrical conductivity, carrier concentration, carrier mobility, thermal conductivity, and figure of merit, were investigated as a function of film thickness and annealing condition. Figures of merit of the thin films annealed at 473 K for 1 hour were improved to be $1.3{\times}10^{-3}K^{-1}$ for p-type and $0.3{\times}10^{-3}K^{-1}$ for n-type, and they were almost independent of film thickness. Temperature sensors were fabricated from the thin films having the above mentioned properties. And thermo-emf, sensitivity, and time constant of the sensors were measured to evaluate their characteristics for temperature sensors. Thin film sensors deposited on Teflon substrates showed better performance than those on glass substrates, and their sensitivity and time constant were 2.91 V/W and 28.2 sec respectively for the sensor of leg width 1 mm$\times$length 16 mm.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.246-252
• /
• 2000

Thermoelectric properties of the $Bi_2(Te_{0.85}Se_{0.15})_3$ alloy, prepared by mechanical alloying and hot pressing, were investigated with the variation of the hot-pressing temperature ranging from $300^{\circ}C$ to $550^{\circ}C$. Contrary to the p-type behavior of single crystal, the hot-pressed $Bi_2(Te_{0.85}Se_{0.15})_3$ alloy exhibited n-type conduction without addition of donor dopant. When the $Bi_2(Te_{0.85}Se_{0.15})_3$ powders were annealed in $(50{\%}\;H_2+50{\%}\;Ar)$ atmosphere, the hot-pressed specimens exhibited a positive Seebeck coefficient due to the reduction of the electron concentration by removal of the oxide layer on the powder surface and annealing-out of the excess Te vacancies. Figure-of-merit of the hot-pressed $Bi_2(Te_{0.85}Se_{0.15})_3$ alloy was improved by hot pressing at temperatures above $450^{\circ}C$, and the maximum value of $1.92{\times}10^{-3}/K$ was obtained for the specimen hot-pressed at $550^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.11-11
• /
• 2010

In order to design for nano structured materials with enhanced thermoelectric properties, the alloys in the pseudo-binary $Bi_2Te_3$-PbTe system were investigated for their micro structure and thermal properties. For this synthesis the liquid alloys were cooled by water quenching method. The micro structure images were taken by using electron probe micro analyzer (EPMA). Dendritic and lamellar structures were clearly observed with the variation in the composition ratio between $Bi_2Te_3$ and PbTe. It was confirmed that a metastable compounds is $PbBi_2Te_4$ in the The $Bi_2Te_3$-PbTe system. The change in the composition increasing $Bi_2Te_3$ ratio causes to change structure from dendritic to lamellar. Seebeck coefficient of alloys 5 which the mixture rate of $Bi_2Te_3$ is 83% was measured as the highest value. In contrast, the others decreased by increasing $Bi_2Te_3$. n-type characteristics was observed at all condition except alloy 6 which $Bi_2Te_3$ ration is 91%. The power factors of all samples were calculated with Seebeck coefficient and resistivity. Also the thermal conductivity was measured by using laser flash analyzer (LFA). In this work, the microstructures and thermal properties have been measured as a function of ratio of $Bi_2Te_3$ in the $Bi_2Te_3$-PbTe system.

• Journal of Powder Materials
• /
• v.31 no.2
• /
• pp.119-125
• /
• 2024

The n-type Bi_2-xSb_xTe₃ compounds have been of great interest due to its potential to achieve a high thermoelectric performance, comparable to that of p-type Bi_2-xSb_xTe₃. However, a comprehensive understanding on the thermoelectric properties remains lacking. Here, we investigate the thermoelectric transport properties and band characteristics of n-type Bi_2-xSb_xTe₃ (x = 0.1 - 1.1) based on experimental and theoretical considerations. We find that the higher power factor at lower Sb content results from the optimized balance between the density of state effective mass and nondegenerate mobility. Additionally, a higher carrier concentration at lower x suppresses bipolar conduction, thereby reducing thermal conductivity at elevated temperatures. Consequently, the highest zT of ~ 0.5 is observed at 450 K for x = 0.1 and, according to the single parabolic band model, it could be further improved by ~70 % through carrier concentration tuning.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.91-96
• /
• 2021

The enhancement of thermoelectric figure of merit was achieved by the simple processes of sieving and high energy ball milling, respectively, which are enable to reduce the grain size of n-type Bi₂Te₃ thermoelectric materials. By optimizing the grain size, the electrical conductivities and thermal conductivities were controlled. In this study, spark plasma sintering was employed for hindering the grain growth during the sintering process. The thermoelectric figure of merit was measured to be 0.78 in the samples with 30 min high energy ball milling process. Notably, this value was 40 % higher than that of pristine Bi₂Te₃ sample. This result shows the properties of thermoelectric materials can be readily controlled by optimization of grain size via simple ball milling process.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.58.2-58
• /
• 2000

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.89-94
• /
• 2010

Bi-Te films were processed by coevaporation of Bi and Te dual sources with variations of the mole ratio of the Bi and Te evaporation sources, and thermoelectric properties of the coevaporated Bi-Te films were characterized. The coevaporated Bi-Te films were n-type semiconductors and exhibited Seebeck coefficients of $-60{\sim}-80{\mu}V/K$. The Terich Bi-Te film, processed with Bi and Te dual sources of 30 mol% Bi : 70 mol% Te ratio, exhibited a power factor of $5{\times}10^{-4}W/m-K^2$. On the other hand, a power factor of $17.7{\times}10^{-4}W/m-K^2$ was obtained for the Bi-rich film coevaporated using Bi and Te dual sources of 90 mol% Bi : 10 mol% Te ratio.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.40-49
• /
• 1997

$Bi_{2}(Te_{0.9}Se_{0.1})_{3}$ thermoelectric matcrials havc 11et:n fahricxted hy mechanical alloying and hot pressing methods. Microstructure and thermoelectric properties of the hot 11resseii $Bi_{2}(Te_{0.9}Se_{0.1})_{3}$ have been investigated Lvith variations of hot pressing temperature and dopmt atltiition Formation of $Bi_{2}(Te_{0.9}Se_{0.1})_{3}$ alloy powders was completed by mechanical alloying of the as-mixed Ri. Te, arid Sc grmules of ~3.6mm size for 3 hours at ball-to-material weight ratio of 5 : 1. Figure of merit of $Bi_{2}(Te_{0.9}Se_{0.1})_{3}$ was markedly incrcwieti hy hot pressing at temperatures above $450^{\circ}C$, and value of $1.9{\times}10^{-3}/K$ was obtained for the specimen hot pressed at $550^{\circ}C$. With addition of 0.015 wt% Ri as acceptor dopant, figure of merit ol $Bi_{2}(Te_{0.9}Se_{0.1})_{3}$ hot pressed $550^{\circ}C$$2.1{\times}10^{-3}/K$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.05a
• /
• pp.68-68
• /
• 1997