• Journal of the Semiconductor & Display Technology
• /
• v.12 no.3
• /
• pp.41-46
• /
• 2013

Efficient and inexpensive solar cells are necessary for photo-voltaic to be widely adopted for mainstream electricity generation. For this to occur, the recombination losses of charge carriers (i.e. electrons or holes) must be minimized using a surface passivation technique suitable for manufacturing. Recently it has been shown that aluminum oxide thin films are negatively charged dielectrics that provide excellent surface passivation of silicon solar cells to attract positive-charged holes. Especially aluminum oxide thin film is a quite suitable passivation on the rear side of p-type silicon solar cells. This paper, it demonstrate the interfacial microstructure and electrical properties of mono-crystalline silicon surface passivated by $Al_2O_3$ films during firing process as applied for screen-printed solar cells. The first task is a comparison of the interfacial microstructure and chemical bonds of PECVD $Al_2O_3$ and of PEALD $Al_2O_3$ films for the surface passivation of silicon. The second is to study electrical properties of double-stacked layers of PEALD $Al_2O_3$/PECVD SiN films after firing process in the temperature range of $650{\sim}950^{\circ}C$.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.4
• /
• pp.138-143
• /
• 2022

We analyzed the influence of post-annealing on Ga₂O₃/n-type 4H-SiC heterojunction diode. Gallium oxide (Ga₂O₃) thin films were deposited by radio frequency (RF) sputtering. Post-deposition annealing at 950℃ in an Oxygen atmosphere was performed. The material properties of Ga₂O₃ and the electrical properties of the diodes were investigated. Atomic Force Microscopy (AFM), X-Ray Diffraction and Scanning Electron Microscope (SEM) images show a significant increase in the roughness and crystallinity of the O₂-annealed films. After Oxygen annealing X-ray Photoelectron Spectroscopy (XPS) shows that the atomic ratio of oxygen increases which is related to a decrease in oxygen vacancy within the Ga₂O₃ film. The O₂-annealed diodes exhibited higher on-current and lower leakage current. Moreover, the ideality factor, barrier height, and thermal activation energy were derived from the current-voltage curve by increasing the temperature from 298 - 434K.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.31 no.2
• /
• pp.95-102
• /
• 2015

Insects are heterotherms that exhibit a close relationship between their ecology (especially temperature changes) and physiology. In the present study, selected genes associated with cell death and temperature were examined to determine gene expression in Bombyx mori in high and low temperature environments. We determined the amount of dsRNA, different concentrations of dsRNA, and different type of cells to set the conditions most efficient for RNAi. We then prepared dsRNA transcripts of the genes associated with cell death and temperature response. We analyzed cell damage via Trypan blue staining and found that cell viability was reduced after knockdown of these genes. The special transduced cell lines produced in the present study can be applied in various research fields. We also expect that these cell lines can be used as a research tool for the precise functional analysis of various genes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.15-16
• /
• 2006

The thermal stability of nickel silicide with compressively and tensilely stressed nitride capping layer has been investigated in this study. The Ni (10 nm) and Ni/Co/TiN (7/3/25 nm) structures were deposited on the p-type Si substrate. The stressed capping layer was deposited using plasma enhanced chemical vapor deposition (PECVD) after silicide formation by one-step rapid thermal process (RTP) at $500^{\circ}C$ for 30 sec. It was found that the thermal stability of nickel silicide depends on the stress induced by the nitride capping layer. In the case of Ni (10 nm) structure, the high compressive sample shows the best thermal stability, whereas in the case of Ni/Co/TiN (7/3/25 nm) structure, the high compressive sample shows the worst thermal stability.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1065-1068
• /
• 1998

On the study, The activated carbon assemblies(ACA) were prepared by activation of the coated glass mate(woven type) with phenolic resin at $700^{\circ}C$ under $N_2$ after drying and curing processes. Surface of the ACA was continuously modified with $N_2$, $CO_2$ or $NH_3$ at $700^{\circ}C$ for 2 hour for comparison of adsorptive characteristics between the ACA and commercial activated carbon cloth. The ACA showed high surface areas up to $2440\;m^2/g$ when converted into the coated carbon base, and the surface was investigated by FT-IR and XPS. The basic ACA modified with $NH_3$ displayed the efficient removal capability of $SO_2$, which is 75% of that in commercial activated carbon cloth. Therefore, it has proved the applicability of ACA as an inexpensive materials for Dry de-SOX system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.78-87
• /
• 2001

The friction and wear behaviors of WC/C multilayer coating were investigated by using a pin on disk type tester. The experiment was conducted by using silicon nitride (S $i_{3}$ $N_{4}$) as a pin material and WC/C multilayer coating on bearing steel (STB2) as a disk material, under various environments that are atmospheric conditions of high vacuum( 1,3$\times$10$^{-4}$ Pa), medium vacuum( 1.3$\times$10$^{-l}$Pa). ambient air( 10$^{5}$ pa)(3 types) and relative humidity(2~98%) conditions. The results showed that WC/C coating fracture was suddenly increased with increasing degree of vacuum, because of high adhesion. So, WC/C coating could not be displayed their ability as solid lubricant. WC/C coating could be displayed better abilitv as solid lubricant with increasing relative humidity. because of oxide film, size and shape of wear debris. The friction coefficient and specific wear rate became better about RH 50%.%.

• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.52-62
• /
• 1990

Cationic polycarbonate type polyurethane was prepared from the quaternization reaction of N-methyldiethanolamine(MDEA) in urethane backbone which was obtained from the reaction of polycarbonate polyol, MDI and MDEA(chain exetender). Tensile strength and modulus of the cationic urethane resins were increased sharply with increasing the ionic content in urethane backbone. But hydrolysis resistance was decreased with increasing ionic contents. The selectivity of the cationic polycabonate urethane membrane for water/ethanol separation by pervaporation was about 20. The carrier mediated transport mechanism was considered the most probable separation mechanism for these membranes.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.717-720
• /
• 1998

On the study, The activated carbon assemblies(ACA) were prepared by activation of the coated glass mat(woven type) with phenolic resin at $700^{\circ}C$ under $N_2$ after drying and curing processes. Surface of the ACA was continuously modified with $N_2$, $CO_2$ or $NH_3$ at $700^{\circ}C$ for 2 hour for comparison of adsorptive characteristics between the ACA and commercial activated carbon cloth. The ACA showed high surface areas up to $2440\;m^2/g$ when converted into the coated carbon base, and the surface was investigated by FT-IR and XPS. The basic ACA modified with $NH_3$ displayed the efficient removal capability of $SO_2$, which is 75% of that in commercial activated carbon cloth. Therefore, it has proved the applicability of ACA as an inexpensive materials for Dry de-SOX system.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.397-400
• /
• 1998

On the study, The activated carbon assemblies(ACA) were prepared by activation of the coated glass mat(woven type) with phenolic resin at $700^{\circ}C$ under $N_2$ after drying and curing processes. Surface of the ACA was continuously modified with $N_2$, $CO_2$ or $NH_3$ at $700^{\circ}C$ for 2 hour for comparison of adsorptive characteristics between the ACA and commercial activated carbon cloth. The ACA showed high surface areas up to $2440\;m^2$/g when converted into the coated carbon base, and the surface was investigated by FT-IR and XPS. The basic ACA modified with $NH_3$ displayed the efficient removal capability of $SO_2$, which is 75% of that in commercial activated carbon cloth. Therefore, it has proved the applicability of ACA as an inexpensive materials for Dry de-SOX system.

• Structural Engineering and Mechanics
• /
• v.74 no.4
• /
• pp.567-576
• /
• 2020

Considerable controversy surrounds the choice of the best abutment type for implant prosthetics. The two most common structures are hex and non-hex abutments. The non-hex abutment typically furnishes a larger contact area between itself and the implant than that provided by a hex structure. However, when a hex abutment is loaded, the position of its contact area may be deeper than that of a non-hex abutment. Hence, the purpose of this study is to determine the different biomechanical behaviors of an internal bone-level implant based on the abutment type-hex or non-hex-and clinical crown length under static and cyclic loadings using finite element analysis (FEA). The hex structure was found to increase the implant and abutment stability more than the nonhex structure among several criteria. The use of the hex structure resulted in a smaller volume of bone tissues being at risk of hypertrophy and fatigue failure. It also reduced micromovement (separation) between the implant components, which is significantly related to the pumping effect and possible inflammation. Both static and fatigue analyses, used to examine short- and long-term stability, demonstrated the advantages of the hex abutment over the non-hex type for the stability of the implant components. Moreover, although its impact was not as significant as that of the abutment type, a large crown-implant ratio (CIR) increased bone strain and stress in the implant components, particularly under oblique loading.