• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.1
• /
• pp.148-154
• /
• 2015

Reports show that global system for mobile communication (GSM) mobile phones, or two-generation (2G) mobile phones, could affect functions of pacemakers and implantable cardioverter defibrillators (ICDs). In this study, we evaluated the effects of radio frequency electromagnetic fields (RF-EMFs) emitted by wideband code division multiple access (WCDMA) mobile phones, which were third-generation (3G) mobile phones, on pacemakers and ICDs. Five pacemakers and three ICDs were subjected to in-vitro test using a ECG simulator. We used a WCDMA module (average power : 0.25 W, frequency band : 1950 MHz) instead of a real WCDMA mobile phone. To assess the effects of the WCDMA module on pacemakers and ICDs, each implantable device was placed in close proximity (within 3 mm) to the WCDMA module for 5 min. As a result, no effects were observed on the five pacemakers and three ICDs for the RF-EMFs emitted by the WCDMA module. Because WCDMA mobile phones have the higher frequency band (1800-2200 MHz) and lower power output (0.01-0.25 W) than GSM moboile phone, the RF-EMFs emitted by WCDMA mobile phones do not affect patients with pacemaker or ICD.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.90-94
• /
• 2007

Location tracking automation of resources in construction industry is one of the most important procedures to improve construction project performance and reduce the period of construction. Recently, location tracking technologies have proven to be effective in tracking construction materials and equipment in real time through the instrumentality of RFID (Radio Frequency Identification). By using wireless communication and inter-working system between RFID and USN, it is possible that construction engineers receive the location information of construction resources without additional efforts that move the RFID reader to read tags periodically. In the inter-working system, RFID reader delivers the acquired materials information to sensor node which is connected by serial interface. Then sensor node transmits the received data to the data aggregation terminal that is a sink node. The data aggregation terminal can transmit collected data to construction manager who is out of construction site using infrastructure such as CDMA(Code Division Multiple Access) network. The combination model of the two system and field test scenarios are presented in this paper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4492-4497
• /
• 2013

An important features of next-generation wireless networks will be heterogeneous environment in which a mobile terminal will be able to connect to multiple radio access networks and network selection mechanisms play an important role in ensuring QoS for users in this environment. In this paper, our study is concerned with an extension of the well known AHP to the group decision making methods. The users requested specific QoS divide into a group and the access networks with similar characteristics split into a group. Between each group, the one group is selected and within that group, the best access networks will be assigned according to priority order by network selection algorithm. The experimental results of MATLAB simulation show that the every user in each services can select the same network with decision value as large as 0.9. Consequently, the proposed network selection mechanism is more effective than conventional one in integrated UMTS and WLAN networks.

• Journal of Korea Society of Industrial Information Systems
• /
• v.13 no.2
• /
• pp.80-87
• /
• 2008

RFID systems are being studied and developed in the area of the industry and marketplace. Recently RFID systems are core element of the ubiquitous technologies in individual life and industry. However, RFID systems often cause some serious problems such as violation of privacy and information security because their contactless devices communicate each other by radio frequency In this paper, we propose multiple objects RFID tag scheme including tag structure and authentication protocol. The proposed RFID tag structure maintains several object IDs of different applications in a tag memory. The tag structure allows those applications to access object IDs simultaneously. The authentication protocol for multiple objects tag is designed ta overcome the problems of security and privacy. The protocol has robustness against various attacks in low cost RFID systems. We evaluate the efficiency of proposed scheme and compare security of our scheme with several traditional schemes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.745-751
• /
• 2018

This paper reports on the design of a multiband multiple-input and multiple-output(MIMO) antenna for long-term evolution(LTE) vehicular communication and includes an analysis of the throughput field test results that were acquired by mounting the antenna to a vehicle. The antenna used for the field test was designed as a planar structure and included multiple stubs to obtain multiband resonant characteristics operating in the LTE(0.8~0.9 GHz, 1.7~2.2 GHz), Wi-Fi(2.4~2.48 GHz), and wireless access in vehicular environments (WAVE)(5.8~5.9 GHz) frequency bands. For the field test, antenna prototypes were mounted on the dashboard and roof of a vehicle and connected to the experimental LTE modem. The data transfer rate(throughput), signal-to-interference-plus-noise ratio(SINR), and reference signal received quality(RSRQ) were measured and analyzed in various real-world radio wave environments. Based on these results, the relationship between the SINR and throughput according to the field intensity is confirmed.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.7
• /
• pp.441-448
• /
• 2012

Spread spectrum provides the minimized inter-symbol interference, the low probability of intercept and the multiple access capability. This paper presents a direct sequence spread spectrum with carrier/timing recovery and equalizer which compensates the delay spread caused by multipath transmission. When the sea trials were performed in Korean East Sea, the bit error rates of QPSK and direct sequence spread spectrum are $1.46{\times}10^{-2}$ and $5.17{\times}10^{-4}$ at 3 km source-receiver range, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.470-476
• /
• 2008

In this paper, we describe the cause of TDMA noise and distinction method of TDMA noise source in a GSM mobile phone. The causes of TDMA noise are composed of RF(Radio Frequency) energy coupling and low frequency energy coupling by burst ripple. We propose the distinction method of TDMA noise source from output(TDMA noise measurement) and frequency response of a system(audio path). Especially we propose a method of insertion loss($S_{21}$) analysis and the improvement method for RF energy coupling. Capacitor(40 pF) is a solution to reduce RF energy coupling and therefore TDMA noise was reduced by 10 dB.

• Journal of Advanced Navigation Technology
• /
• v.12 no.3
• /
• pp.220-226
• /
• 2008

This paper proposes the Reconfigurable Doherty Amplifier(RDA) with asymmetric structure which has ${\lambda}/4$ impedance transformer for modulating the load impedance in peaking amplifier path. This structure is possible to implement a compact size for N-stage multi Doherty amplifier and to get almost same characteristics that is compared to conventional Doherty amplifier. To realize the high efficiency amplifier, we were implemented 45 Watts power amplifier at transmitter band of Wideband Code Division Multiple Access(WCDMA) base-station. As a result, in case of WCDMA 1 Frequency Allocation(FA) input signals, this amplifier has obtained a 26.3% Power Added Efficiency(PAE) at 8 dB back-off point from P1dB and an Adjacent Channel Leakage Power(ACLR) is -40.4 dBc at center frequency ${\pm}5MHz$ deviation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.5
• /
• pp.12-20
• /
• 2008

RFID(Radio frequency indentification) technology, that the reader detect the tag information attached on the objects without contact, is considered the kernel of realizing tile Ubiquitous Sensor Network. Particularly, because there are lots of tags(which the reader have to detect) in the UHF RFID system(that is applied at the Logistic & Distribution industry). In the UHF RFID system the negative effects, we called the tag-collision, may occur and we should solve these effects. So, in the EPCglobal Gen2 protocol they present the Slotted Random Anti-collision algorithm to prevent the tag-collision effect. In this paper, in order to minimize the tag-collision effect and bring on the system efficiency, we propose the Power Increasing Method that controls the transmission power of the reader depending on the environment and verily the improved performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.7
• /
• pp.986-992
• /
• 2021

To stabilize closed-loop wireless control systems, the state-of-the-art approach receives the individual sensor measurements at the controller and then sends the computed control signal to the actuators. We propose an over-the-air controller scheme where all sensors attached to the plant transmit scaled sensing signals simultaneously to the actuator, and the actuator then computes the feedback control signal by scaling the received signal. The over-the-air controller essentially adopts the over-the-air computation concept to compute the control signal for closed-loop wireless control systems. In contrast to the state-of-the-art sensor-to-controller and controller-to-actuator communication approach, the over-the-air controller exploits the superposition properties of multiple-access wireless channels to complete the communication and computation of a large number of sensing signals in a single communication resource unit. Therefore, the proposed scheme can obtain significant benefits in terms of low actuation delay and low resource utilization with a simple network architecture that does not require a dedicated controller.