• Journal of Advanced Marine Engineering and Technology
• /
• v.9 no.4
• /
• pp.328-338
• /
• 1985

When the low temperature service steels are used as materials for welded structure, some problems-brittleness and weld cracking, etc.-occur in welded part due to the change of mechanical and metallurgical characteristics resulted from the thermal cycle during the welding procedure. In this study, the experiments were conducted to investigate the change of mechanical and metallurgical characteristics of the welded part for the low temperature and high pressure service steels. Moreover, the Static and Dynamic Implant Test Method was introduced to this study in order to find out the mechnism of weld cracking. In addition, the fracture toughnesses of welded bond were inspected under the various low temperature environments. Main results obtained are as follows; 1) The effect of the hydrogen on the fatigue characteristics of the weld bond can be estimated by the new self-contrived Dynamic Implant Test equipment. 2) The fine micro-structure and low hardness in the heat affected zone can be obtained by the small heat input multi-pass welding. 3) The susceptibility of the delayed cracking is largely affected by the condition of used electrode. 4) The transition temperature of the fracture surface in weld bond appears to be higher 20 .deg. C than that in base metal.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.4
• /
• pp.667-674
• /
• 2004

This thesis is about the Impressed Current Cathodic Protection (ICCP) control and monitoring system. which brings protection against the corrosion of the ship's hull in the sea environments. The ICCP system is composed of a power supply. anode. reference electrode and controller. AC sources from the ship's generator are converted to DC sources in terms of power supply, and a protection current is sent to ship's hull though anode. The controller fully senses whether or not the detected potential is within a range of protection of ship's hull and then it is automatically controlled to increase or decrease the amount of protective current to be sent to the anode. The monitoring system with RS 232/485 communication is also studied in order to check the normal state of the system at a long period. because an operator does not always watch over this system and thus the system cannot operate well because of his or her negligent management. Since the vessel always navigates in the sea. an characteristics experiment of the ICCP system is conducted by introducing various corrosive environmental factors such as velocity, resistivity, dissolved oxygen, PH, temperature and contamination degree. These results must be referred to when the ICCP system is set up. In short. the ICCP is a multi-system for use on ships and on land structures because it includes a safety device. It is suggested that this system can accomodate a ship's automation and will be very useful.

• Journal of Korea Multimedia Society
• /
• v.19 no.7
• /
• pp.1146-1153
• /
• 2016

The bioelectrical impedance (BI) at the inner forearms was measured using bioelectrical impedance measurement system (BIMS), which employs the multi-frequency and the two-electrode method. Experiments were performed as follows. First, while applying a constant alternating current of 800A to the inner region of the forearms, BI (Z) was measured at nineteen frequencies ranging from 5 to 500 kHz. The prediction marker (PM) was calculated for right and left forearm. The resistance (R) and the reactance (X_c) were simultaneously measured during impedance measurement. Second, a Cole-Cole plot (relationship between reactance and resistance) was obtained for left and right forearm, indicating the different characteristic frequencies (f_c). Third, the phase angle was obtained, indicating strong dependence on the applied frequency.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.409-412
• /
• 2006

EEFL can be driven by square wave driving method. A square wave is applied directly to both ends of EEFL by cascaded multi-stage full-bridge inverter. The various current shapes of lamp are achieved by various inductors between lamp and inverter. In this paper, it is newly investigated that the area of current directly influences the luminance. Furthermore, the 3-level square wave is considered to drive EEFL with self-discharge characteristics. The highest luminance efficiency is achieved by properly controlling the rate of self-discharge usage.

• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.301-308
• /
• 1993

Phenomenological nonlinear gain saturation effect on the modulation characteristics in a multi-electrode DBR laser, when the lasing wavelength changes, continuously is analized theoretically. FM efficiency, 3 dB bandwidth, and resonance frequency decrease with increasing bias current to the passive section, except increasing the flat FM response. It is found that the nonlinear gain saturation effect severely affects the modulation characteristics such as FM/IM response, 3 dB bandwidth, resonance frequency and CPR, but hardly affects the behavior of continuous frequency tuning.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.42-49
• /
• 2005

In general, multi-lap spot weld joints are frequently present in automobile. Most research, however, has been focused on the single-lap spot weld joints until now. In this paper, tensile-shear strength tests are performed to examine the weldability of 3-lap spot joint welded by using the high strength steel sheet and the zinc coated steel sheet. The indentation depth and nugget diameter are used to propose the optimum welding conditions. The weldability is affected by the welding current and welding time for 3-lap spot joint. Meanwhile the expulsions is round to decrease with the increase of electrode force. The optimum welding conditions are presented for 3-lap spot joints of high strength steel sheet and zinc coated steel sheet.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.97.1-97.1
• /
• 2018

본 연구는 초고온 열처리 과정에서 멀티레이어 투명전극 박막의 고내열성, 고신뢰성을 얻기 위해 보호층을 삽입한 연구이다. 먼저 보호층의 고내열 효과를 알아보기 위해 보호층을 삽입한 박막과 그렇지 않은 박막을 200, 300, 400, 500, $550^{\circ}C$로 각각 열처리하여 비교하였다. 보호층을 삽입하지 않은 박막은 $500^{\circ}C$에서 멀티레이어 박막이 응집하여 전기적 광학적 특성이 저하되었다. 반면, 보호층을 삽입한 박막은 $550^{\circ}C$에서도 투과율 (%T) 89.5% (at 550nm wavelength), 면저항 $3.5{\Omega}/sq$로 투명전극으로서 뛰어난 특성을 보였다. 또한 고신뢰성을 확인하기 위해 상대습도 85%, 온도 $85^{\circ}C$ 조건에서 120시간 동안 항온항습 테스트를 수행하였다. 보호층이 없는 투명전극의 박막은 산화가 일어나 전기적 광학적 특성이 저하 되었으나, 보호층을 삽입한 투명전극의 박막은 전기적 광학적 특성의 변화가 거의 없는 것으로 확인되어 본 멀티레이어 투명전극에서 보호층의 핵심적인 효과를 입증할 수 있었다.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.211-218
• /
• 2009

For the Y5V characteristic MLCC which is very prone to crack, it is important to to find out the basic cause of the crack. After finding out the crack origin, the materials and processes should be developed to remove the crack. The microstructures of the cracks were investigated using the fractographic method for the various types of cracks such as an exterior crack, a cyclic thermal shock crack, and an piezo-electric crack. It was found out that the crack origin was the pore at the end of the Ni inner electrode after bake-out. Even though the three dimensional crack shapes were different, the crack origins were seemed to be similar. The exterior crack could grow from the origin with the aids of residual and applied stress. FEM (finite element method) analysis was used to calculate the stress distribution of residual and applied stress. And the concept of fracture mechanics was applied for the explanation of the crack initiation and propagation from the stresses concentration.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.983-989
• /
• 2005

[ $PZT(Pb(Zr,Ti)O_3)$ ] thin films were deposited by multi-target reactive sputtering method on $RuO_2$ substrates. Pure perovskite phase PZT films could be obtained by introducing Ti-oxide seed layer on the $RuO_2$ substrates prior to PZT film deposition. The PZT films deposited on the $RuO_2$ substrates showed highly voltage-shifted hysteresis loop compared with the films deposited on the Pt substrates. The surface of $RuO_2$ substrate was found to be reduced to metallic Ru in vacuum at elevated temperature, which caused the formation of oxygen vacancies at the initial stage of PZT film deposition and gave rise to the voltage shift in the P-E hysteresis loop of the PZT capacitor. The fatigue characteristics of the PZT capacitors under unipolar wane electric field were different from those under bipolar wane. The fatigue test under unipolar wane showed the increase of polarization. It was thought that the ferroelectric domains which had been pinned by charged defects such as oxygen vacancies and the charged defects were reduced in number by combining with the electrons injected from the electrode under unipolar wave, resulting in the relaxation of the ferroelectric domains and the increase of polarization.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.8
• /
• pp.476-482
• /
• 2016

Convectional PZT based piezoelectric ceramics have to sinter at high temperature about $1,200^{\circ}C$ for their suitable electrical properties. However, some issues: low temperature sintering piezoelectric ceramic composition and reliable internal electrode, have recently attracted a great deal of interest as a highly efficient multi-layered piezoelectric ceramics. In order to optimize low temperature sintering conditions of thick-film PMN-PZ-PT ceramic, it was investigated sintering and piezoelectric properties according to the change of $LiBiO_2$ contents. Thus, the superior piezoelectric properties were found at the pallet type PMN-PZ-PT optimized with low sintering processing at $925^{\circ}C$ including 7 wt% $LiBiO_2$ sintering aid. Consequentially, we successfully manufactured thick-film PMN-PZ-PT ceramics, which had superior piezoelectric and dielectric properties, with 5 wt% of $LiBiO_2$ sintering aid at temperature of $900^{\circ}C$.