• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.6
• /
• pp.3208-3229
• /
• 2017

Rectification is an essential procedure for simplifying the disparity extraction of stereo matching algorithms by removing vertical mismatches between left and right images. To support real-time stereo matching, studies have introduced several look-up table (LUT)- and computational logic (CL)-based rectification approaches. However, to support high-resolution images, the LUT-based approach requires considerable memory resources, and the CL-based approach requires numerous hardware resources for its circuit implementation. Thus, this paper proposes a multi-level accumulation-based rectification method as a simple CL-based method and its circuit implementation. The proposed method, which includes distortion correction, reduces addition operations by 29%, and removes multiplication operations by replacing the complex matrix computations and high-degree polynomial calculations of the conventional rectification with simple multi-level accumulations. The proposed rectification circuit can rectify $1,280{\times}720$ stereo images at a frame rate of 135 fps at a clock frequency of 125 MHz. Because the circuit is fully pipelined, it continuously generates a pair of left and right rectified pixels every cycle after 13-cycle latency plus initial image buffering time. Experimental results show that the proposed method requires significantly fewer hardware resources than the conventional method while the differences between the results of the proposed and conventional full rectifications are negligible.

• Journal of the Korean Society of Combustion
• /
• v.20 no.4
• /
• pp.26-33
• /
• 2015

American NREL (National Renewable Energy Laboratory) reported that BD20 could reduce PM, CO, SOx and cancerogenic matters by 13.6%, 9.3%, 17.6% and 13% respectively, compared to diesel fuel. BD20 has been being tested on garbage trucks and official vehicles at Seoul City, which is positive on air environment, but negative on combustion by higher viscosity in winter season. This study investigated the combustion characteristics by employing multi cavity piston for improving the deterioration of combustibility caused by the higher viscosity of the biodiesel fuel such as BD20 with the combustion flames taken by a high speed camera and the cylinder pressure diagram. A 4-cycle single cylinder diesel engine was remodeled to a visible 2-cycle engine for taking the flame photographs, which has a common-rail injection system. The test was done at laboratory temperature of about $4{\sim}5^{\circ}C$.

• International conference on construction engineering and project management
• /
• 2007.03a
• /
• pp.625-634
• /
• 2007

Energy-saving is one of important issues in multi-family housing projects in South Korea. According to the study by Yu et al. (2002), the balcony conversion causes energy loss approximately one and a half times. Therefore, it is important to select the economical glass type in the balcony window. In order to identify the most economical glass type of balcony conversion in multi-family housing projects, the most typical type of the multifamily housing projects in the metropolitan area was selected as a candidate project. The selected candidate project has been simulated using ENERGY-10 program to estimate the heat load by the different five types of glasses as well as their life cycle cost analysis (LCCA) using present worth method. Finally, sensitivity analysis has been conducted to determine the most economical glass types under a different discount rate (interest rate) and service life of building.

• Nuclear Engineering and Technology
• /
• v.56 no.5
• /
• pp.1654-1666
• /
• 2024

The goal of this research is to propose a way to maximize small modular reactor (SMR) utilization to gain better market feasibility in support of carbon neutrality. For that purpose, a comprehensive tool was developed, combining off-design thermohydraulic models, economic objective models (levelized cost of electricity, annual profit), non-economic models (saved CO2), a parameter input sampling method (Latin hypercube sampling, LHS), and a multi-objective evolutionary algorithm (Non-dominated Sorting Algorithm-2, NSGA2 method) for optimizing a SMR-combined heat and power cycle (CHP) system design. Considering multiple objectives, it was shown that NSGA2+LHS method can find better optimal solution sets with similar computational costs compared to a conventional weighted sum (WS) method. Out of multiple multi-objective optimal design configurations for a 105 MWe design generation rating, a chosen reference SMR-CHP system resulted in its levelized cost of electricity (LCOE) below $60/MWh for various heat prices, showing economic competitiveness for energy market conditions similar to South Korea. Examined economic feasibility may vary significantly based on CHP heat prices, and extensive consideration of the regional heat market may be required for SMR-CHP regional optimization. Nonetheless, with reasonable heat market prices (e.g. district heating prices comparable to those in Europe and Korea), SMR can still become highly competitive in the energy market if coupled with a CHP system.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.67-87
• /
• 1991

The computer program which predicts the gas exchange process of multi-cylinder 4-Stroke cycle spark-ignition engine, can be great assistance for the design and development of new engine. In this study, the computer program was developed to predict the gas exchange process of multi-cylinder four stroke cycle spark ignition engine including intake and exhaust systems. When gas exchange process is to be calculated, the evaluation of the variation of the thermo-dynamic properties with time and position in the intake and exhaust systems is required. For the purpose, the application of the generalized method of characteristics to the gas exchange process is known as one of the method. The simulation model developed was investigated to the analysis of the branch system of multi-cylinder. The models used were the 2-zone expansion model and single zone model for in cylinder calculation and the generalized method of characteristic including area change, friction, heat transfer and entropy gradients for pipe flow calculation. The empirical constants reduced to least number as possible were determined through the comparison with the experimented indicator diagram of one particular operation condition and these constants were applied to other operating condition. The predicted pressures in cylinder were compared with the experimental results over the wide range of equivalence ratio and ignition timing. The predicted values have shown good agreement with the experimental results. The thermodynamic properties in the intake and exhaust system were predicted over the wide range of equivalence ratio and ignition timing. The obtained results can be summarized as follows. 1. Pressures in the exhaust manifold have a little influence on the equivalence ratio, a great influence on the ignition timing. 2. Pressures in the inlet manifold are nearly unchanged by the equivalence ratio and the ignition timing. 3. In this study, the behaviors of the exhaust temperature, gas in the exhaust manifold were ascertained.

• Transactions of Materials Processing
• /
• v.30 no.4
• /
• pp.172-178
• /
• 2021

The cold forging process induces material deformation in an enclosed space, generating a very high forging load. Therefore, it is mainly designed as a multi-stage process, and fatigue failure occurs in forging die due to cyclic load. Studies have been conducted previously to quantitatively predict the fatigue limit of cold forging dies, however, there was a limit to field application due to the large error range and the need for expert intervention. To solve this problem, we conducted a study on the introduction of a real-time forging load measurement technology and an automated system for quantitative prediction of die life cycle. As a result, it was possible to reduce the error range of the quantitative prediction of die life cycle to within ±7%, and it became possible to use the die life cycle calculation algorithm into an automated system.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2003

Generally, the life-span of a multi-housing complex is over 50 years, but in reality they are usually demolished after 20 years in spite of its remaining life expectancy. Thus, this research focuses on the estimation of the optimum economic life-span of a multi-housing complex. To estimate the minimum total cost point of start to finish of a multi-housing complex, we'll apply MAPI(Machinery and Allied Product Institute) and LCC(Life Cycle Cost) theory.

• Korean Journal of Agricultural Science
• /
• v.48 no.4
• /
• pp.1027-1037
• /
• 2021

This study aims to evaluate the performance of an electric multi-purpose cultivator through a simulation analysis. The simulation model was developed using commercial software, Simulation X, by applying the specifications of certain parts, such as an electric motor, a battery, and so on. The input parameter of the simulation was the engine load data according to the rotary tillage level using a conventional multi-purpose cultivator. The data were collected by configuring a load measurement system, and the load cycle was developed by repeating the data collection process under the most severe conditions. The average output engine torque values of conventional multi-purpose cultivator were 10.7, 13.0, 9.4, and 11.2 Nm in the D1P1, D1P2, D2P1, and D2P2 conditions, respectively. As a result of the simulation, the maximum values of the motor torque, rotational speed, and power of the electric multi-purpose cultivator were 16.8 Nm, 2,033.3 rpm, and 3.3 kW, respectively, and the motor was driven in sections within 70, 68, and 45% of the maximum output range. The rate of decrease of the battery state of charge (SOC) level per minute was approximately 0.6%, and it was possible to supply electric power to the motor for 9,550 sec. In the future study, research to verify and improve simulation models of electric multi-purpose cultivators should be conducted.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.437-447
• /
• 2017

In current, there has not been the evaluation model for the optimum design of the multi-utility tunnel by considering urban type and size, the function of surrounding road and feasibility analyses with respect to construction method, and arrangement of accommodation facilities inside multi-utility tunnel. Thus, in this study, we developed the evaluation model for the optimum design of the multi-utility tunnel before and after the decision of the multi-utility tunnel installation. In this paper, we have selected the Deming cycle which is used in various fields among several decision methods for optimizing the design. For the purpose of reflecting the various factors in the design of the multi-utility tunnel, 11 higher indicators were set up to lead to more detailed approaches. In addition, based on the "Plan-Do-Check-Action (PDCA)" circulation method, we can realize the installation of the multi-utility tunnel and design more efficiently through the first phase for conception and the second phase for optimization, and develop the program for the evaluation model accordingly.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.11_12
• /
• pp.629-638
• /
• 2005

In the System on a Chip design, the on chip bus is one of the critical factors that decides the overall system performance. Especially, in the case or reusing the IPs such as processors, DSPs and multimedia IPs that requires higher bandwidth, the bandwidth problems of on chip bus are getting more serious. Recently ARM proposes the Multi-Layer AHB BusMatrix that is a highly efficient on chip bus to solve the bandwidth problems. The Multi-Layer AHB BusMatrix allows parallel access paths between multiple masters and slaves in a system. This is achieved by using a more complex interconnection matrix and gives the benefit of increased overall bus bandwidth, and a more flexible system architecture. However, there is one clock cycle delay for each master in existing Multi-Layer AHB BusMatrix whenever the master starts new transactions or changes the slave layers because of the Input Stage and arbitration logic realized with Moore type. In this paper, we improved the existing Multi-Layer AHB BusMatrix architecture to solve the one clock cycle delay problems and to reduce the area overhead of the Input Stage. With the elimination of the Input Stage and some restrictions on the arbitration scheme, we tan take away the one clock cycle delay and reduce the area overhead. Experimental results show that the end time of total bus transaction and the average latency time of improved Multi-Layer AHB BusMatrix are improved by $20\%\;and\;24\%$ respectively. in ease of executing a number of transactions by 4-beat incrementing burst type. Besides the total area and the clock period are reduced by $22\%\;and\;29\%$ respectively, compared with existing Multi-layer AHB BusMatrix.