• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.5
• /
• pp.572-579
• /
• 2006

Accurate heat release analysis based on the cylinder pressure trace is important for evaluating combustion process of diesel engines. However, traditional single-zone heat release models (SZM) have significant limitations due mainly to their simplified assumptions of uniform charge and homogeneity while neglecting local temperature distribution inside cylinder during combustion process. In this study, a heat release analysis based on single-zone model has been evaluated by comparison with computational simulation result using Fire-code, which is based on multidimensional model (MDM). The limitations of the single-zone assumption have been estimated, To overcome these limitations, an improved model that includes the effects of spatial non-uniformity has been applied. From this improved single-zone heat release model (Improved-SZM), two effective values of specific heat ratios, denoted by ${\gamma}_V$ and ${\gamma}_H$ in this study, have been introduced. These values are formulated as the function of charge temperature changing rate and overall equivalence ratio. Also, it is applied that each equation of ${\gamma}_V$ and ${\gamma}_H$ has respectively different slopes according to several meaningful periods during combustion progress. The heat release analysis results based on improved single-zone model gives a good agreement with FIRE-code results over the whole range of operating conditions of target engine, Hyundai HiMSEN H21/32.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.609-614
• /
• 2014

In this research, results of measuring temperature and relative humidity of underground-air-heat in Jeju showed $15{\sim}18^{\circ}C$ and 70~80% each which are somewhat high compare to other regions. So the Multi-effect dehumidifying and heating Heat Pump system which has merged functions of dehumidification and heating is made to solve this problem mentioned previously. When the suction air was $15^{\circ}C$ with 60% humidity, the outcome was 1.70 on $COP_h$ and 1.797(kg/h) on total amount of dehumidification, and also showed 1.87 $COP_h$ with 1.87 total amount of dehumidification under the condition of $20^{\circ}C$ and 80% humidity of suction air. Furthermore, $COP_h$ showed increased number which is 1.87 and also total amount of dehumidification increased which was 3.269(kg/h). The highest COP can be achieved at $17^{\circ}C$ and 70% relative humidity condition.

• Progress in Medical Physics
• /
• v.26 no.1
• /
• pp.36-41
• /
• 2015

The Monte Carlo based dose calculation program for stereotactic body radiotherapy was developed in this study. The Geant4 toolkit widely used in the radiotherapy was used for this study. The photon energy spectrum of the medical linac studied in the previous research was applied for the patient dose calculations. The geometry of the radiation fields defined by multi-leaf collimators were taken into account in the PrimaryGeneratorAction class of the Geant4 code. The total of 8 fields were demonstrated in the patient dose calculations, where rotation matrix as a function of gantry angle was used for the determination of the source positions. The DicomHandler class converted the binary file format of the DICOM data containing the matrix number, pixel size, endian type, HU number, bit size, padding value and high bits order to the ASCII file format. The patient phantom was constructed using the converted ASCII file. The EGSnrc code was used to compare the calculation efficiency of the material data.

• Journal of Wetlands Research
• /
• v.13 no.1
• /
• pp.53-66
• /
• 2011

We estimated the expected flood damage considering uncertainty which is involved in hydrologic processes and data. Actually, this uncertainty represents a freeboard or safety factor in the design of hydraulic structures. The uncertainty was analyzed using Bootstrap method, and SIR algorithm then the frequency based rainfalls were estimated for each method of uncertainty analysis. Also the benefits for each uncertainty analysis were estimated using 'multi-dimensional flood damage analysis(MD-FDA). As a result, the expected flood damage with SIR algorithm was 1.22 times of present status and Boostrap 0.92 times. However when we used SIR algorithm, the likelihood function should be selected with caution for the estimation of the expected flood damage.

• Journal of Wetlands Research
• /
• v.19 no.2
• /
• pp.181-192
• /
• 2017

Analysis using a numerical model is important to understand the sediment transport mechanism associated with erosion and sedimentation near weirs and other hydraulic structures within riverine systems. The local riverbed change near a hydraulic structure (Gangjeong-Goryong multi-function weir in the Nakdong river) was analyzed in order to examine the effect of hydraulic structures on local bed change. A 2D numerical model (CCHE-2D) was employed to simulate the sedimentation and erosion over a reach (25 km) including the weir. For the calibration and verification of the model, rainfall data from a real event (Typoon 'Ewiniar' in 2006) were used for flow and stage simulation. And the simulated results show a good agreement with the observed data for the whole domain. From the result, it was found that the installation and operation of the weir could aggravate bed changes by typhoon between movable weirs, and which resulted in redistribution of sediment.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.214-217
• /
• 2003

The connectorless power supply system on that multi-contact causes confidence when the wiring reconstructed in the rear. As you see above, contact points between sets and indoor space cause inferior function of audio frequency so it needs to be eliminated. This paper explains the structure of connectorless power supply to supply the system with power crossing the air gap in the part of inductively in the connectorless power supply of both magnetic and electrical model. To get maximum output of electrical load, compensating capacitor compensates to show inter-inductance, lequeage-inductance reducing the track-inductance and access the conditions for resonance. At that time it accesses the maximum electric power. The small change of the value of compensating capacitor causes the changes of maximum electric power. Here the power electronics technology is used not only in the industrial machinery but also in the home appliances so the switching power supply is used to actualize the miniaturization, lightweight, and high efficiency. Generally the condenser input methods are widely used in the rectification circuit of switching power supply, but condenser input method generate great quantity of high frequency components because with this method the current flows in the power input filtering condenser only around value of peak of ac input voltage. To solve these problems, installation of power factor improve circuit on the front of filtering capacitence was considered. Several methods were suggested regarding, but the active filter method which makes smalliging and highly power factor possible are the produce main stream. IC for power factor improvement can be utilized by CMOS process proposing low power consumption. When the high power factor is considered seriously in the power factor improvement circuit, active filter method is selected. In the active filter method, the boost converter is used. Regarding this ·the boost converter is needed.

• Korean Institute of Interior Design Journal
• /
• v.22 no.5
• /
• pp.284-292
• /
• 2013

The study performed analysis focusing on specialized convention and exhibition facilities among convention and exhibition facilities in Korea. The procedures and results were as follows: First, by theoretical consideration, meaning and contents of convention and exhibition programs done in convention and exhibition facilities were considered and after that, general characteristics of the programs which were the main of space utilization was derived. Second, considering scale and location, 6 facilities were re-selected for in-depth research from 12 facilities investigated preliminarily. Selected facilities were categorized by scale and through the analysis of programs done in this facilities for the last 1 year, overview and characteristics of utilization for exhibition space, conference space, and multi-purpose space, etc were analyzed. Third, through the case study on the programs, individual characteristics of space utilization by convention and exhibition program were analyzed. From the result of the study, considering the whole, the space utilization of programs was done as conference space rather than exhibition space and the ratio of use as conference space to use as exhibition space was 1.8 in the large facilities, 6.7 and 7.6 in the middle facilities and the small facilities, respectively. In the middle and small facilities, the ratio of use of one room as conference space was very high. In the large facilities, there was no big difference with the ratio 50:50 of the programs involving exhibition to other programs, but in the middle and small facilities, the ratio of the former to the latter was observed over 2.4 and 3.6. This fact indicated that the function of use as promotion and communication space for companies and industrial entities which were the essential purposes became low.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.5
• /
• pp.1151-1161
• /
• 1998

In this paper, we are considering a heterogeneous processor system in which each processor may have different performance and reliability characteristics. In other to fully utilize this diversity of processing power it is advantageous to assign the program modules of a distributed program to the processors in such a way that the execution time of the entire program is minimized. This assignment of tasks to processors to maximize performance is commonly called load balancing, since the overloaded processors can perform their own processing with the performance degradation. For the task assignment problem, we propose a new objective function which formulates this imbalancing cost. Thus the task assignment problem is to be carried out so that each module is assigned to a processor whose capabilities are most appropriate for the module, and the total cost is minimized that sum of inter-processor communication cost and execution cost and imbalance cost of the assignment. To find optimal assignment is known to be NP-hard, and thus we proposed an efficient heuristic algorithm with time complexity $O(n^2m)$ in case of m task modules and n processors.

• The KIPS Transactions:PartD
• /
• v.13D no.7 s.110
• /
• pp.923-930
• /
• 2006

In this paper we design the system test model for the weapon system embedded software based on the Time Factor Method(TFM) considering time factors and suggest the results through the case study. For doing this, we discuss the features, system tests and the object-oriented model based UML notations of the weapon system embedded software. And we give a test method considering time factors, a measuring method to time factors, and a test case selection algorithm as an approach to the TFM for designing the system test model. The TFM based system test model consists of three factors (X, Y, Z) in the weapon system embedded software. With this model, we can extract test cases through the selection algorithm for a maximum time path in 'X', identify the objects related to the Sequence Diagram in 'Y' and measure the execution time of each objects which is identified by the Timing Diagram in 'Z' Also, we present the method of extracting the system test cases by applying the proposed system test model to the 'Multi-function missile defense system'.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.1
• /
• pp.53-62
• /
• 2010

Recently, various industrial embedded systems including vehicles controlled electronically are evolving to distributed multi-micro controller system. Accordingly, there is a need for standard CAN(Controller Area Network) protocol that ensures high stability and reliability of communication and is simple to construct object-oriented system with high control efficiency. CAN communication interface used general-purpose processor doesn't have many limitations in various application development because of fixed hardware architecture. This paper design and implement a CAN communication interface system based on FPGA. It is verified function and performance of system through monitoring communication with existing AT90CAN128 controller. Implemented CAN communication interface can be reused in development of application systems based on FPGA. And it provides low-cost, small-size and low-power design advantages.