• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.118-123
• /
• 2003

Motor-driven systems are the largest electrical load and share about 40％ of electric energy consumption in Korea. Increasing the efficiency of drive-power systems, therefore, is one of the most urgent demand side programs to be designed and launched. This paper presents an extensive analysis on the alternative rebate programs viable to enhancing the adoption of high-efficiency induction motors, and suggests government activities supporting market transformation initiatives.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.76-81
• /
• 2012

In-process evaluation equipment for the prominent discrete tone (PDT) emitted by small motors or actuators such as HDD(Hard Disk Driver), ODD(Optical Disk Driver) or linear motors has been developed and estimated on the basis of Prominence Ratio (PR) method in ECMA 74. Correlation of the evaluation equipment was performed in comparison with the method by ECMA 74 in anechoic chamber. Coherent function between two systems was applied in order to compensate traceability of ECMA 74 in anechoic chamber. Usability of the developed system with estimated Gage R&R shall be approved with real samples in the mass production line.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.17-23
• /
• 1996

Gerotor Pump and Motors are widely used in lubrication and hydraulic actuator systems, These have many advantage compared with internal gear pump and motors, But the gerotor profile have not been sufficiently analyzed theoretically. So it is vary difficult for designer to decide the specifications of the gerotor profile, and it is not yet confirmed to calculating flow rate and minimum distance of clearance in the contact point of inner and outer rotor. In this paper, When we design inner and outer rotor concurently, We have analyzed the gerotor and displayed the calculated results such as flow rate, minumum distance between inner and outer rotor and gerotor profiles

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.4
• /
• pp.253-263
• /
• 2002

This paper presents an adaptive feedback linearization control scheme for induction motors using stator fluxes. By using stator flukes as states, overparameterization is prevented and control inputs can be determined straightforwardly unlike in existing schemes. This approach leads to the decrease of the relative degree for the flux modulus and thus yields a simpler control algorithm than the prior results. In this paper. adaptation schemes are suggested to compensate for the variations of stator resistance. rotor resistance and load torque. In particular, the adaptation to the variation of stator resistance with a feedback linearization control is a new trial. In addition, to improve the convergence of rotor resistance estimation, the differences between stator currents and its estimates are used for the parameter adaptation. The simulations show that torque and flux are controlled independently and that the estimates of stator resistance, rotor resistance, and load torque converge to their true values. Actual experiments on a 3.7㎾ induction motor verify the effectiveness of the proposed method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.2
• /
• pp.417-423
• /
• 2012

In this paper, In order to make up for the weak point of driving structure that existing used single motor in motor design, as a method to make use of advantage for joint of hollow type, we propose implementation methods for high torque, high precision, backlash less, and design of secondary safety device, and application method through joint organization using multiple motors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.425-429
• /
• 2007

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 18 % under the speed 0.14 m/s, thrust 345 gf and preload 280 gf, operating frequency is 57.6 kHz.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.6-8
• /
• 2004

Recently, it is increasing to use more Brushless DC Motor with high energy density permanent magnet and semiconductor control unit for complementing the mechanical defect of Brushed DC Motors. For designing of BLDC Motors are required complex parameters like as rated characteristic, Geometries, B-H curve of magnet and steel materials, winding factor, etc. Moreover, design and manufacturing are difficult because of additional control circuits. Generally, Design parameters are gotten by analysis of Motor which is used. And the design parameters are used to design a new motor. But getting the design parameters through the eyes and experience is limited and it takes a long time. In this paper a method is proposed to efficiently analyze motor design parameters through the No load and Load Test, Back EMF Test, Simulation Analysis and Patent Analysis Method for existing BLDC Motor for a cooling Fan in Vehicle.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.65-67
• /
• 2004

In this paper, we Present two-dimensional (2-D) analytical model for predicting the magnetic field characteristic of slotless permanent magnet bushless motors. Results from the model are compared to those deduced from 2-D finite element analyses(FEA). It is shown that the radial magnetization and the parallel magnetization of permanent magnet can have flux density on coil, airgap and permanent magnet's surface.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.72-76
• /
• 1997

Interior permanent magnet synchronous motors can be applied to applications requiring wide-speed operation. The current control scheme of an interior permanent magnet synchronous (IPM) motor via feedback linearizing technique is proposed. As the available voltage controlling the armature current is small in transient operations and/or flux-weakening region, the current control performance can be deteriorated. The high performance overmodulation strategy is also proposed to improve the current responses. The control performances are confirmed by simulations.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.9-11
• /
• 1995

In this paper, tile squirrel case induction motors required multi-objective function are designed. As the objective function of the optimization program, we select the linear combination of loss and mass of motors by using weighting factors. Optimization process is performed by using the evolution strategy (ES). ES is the algorithm that can find the global minimum. To verify validity of the proposed method, a sample design is tried.