• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.4
• /
• pp.281-285
• /
• 2013

In this paper, a design scheme of a cruise control system for an electric vehicle using piece-wised PD control is proposed. Cruise control of electric vehicles is one of the major performance elements. Drive motors having linear characteristics ideally is required in order to achieve the cruise driving. But practical motors have nonlinear characteristics and the performance of the motors can be improved by the closed-loop control to compensate it. In this paper, we improved the performance of by applying piece-wised PD control because the driving motors having nonlinear characteristics are difficult to obtain adequate performance only using closed-loop control. In order to test the proposed method, the experiments were carried out by applying the proposed method after setting up an electric vehicle equiped with a driving motors having large nonlinear characteristics. The experiment results of the proposed piece-wised PD control shows better performance than that of closed-loop control.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.119-128
• /
• 2004

With the growing traffic density and increasing comfort requirements, the automation of the drive train will gain importance in vehicles. The automatic clutch actuation relieves the drivers especially in urban driving and stop-and-go traffic conditions. This paper describes the dynamic modeling of a clutch actuator and clutch spring. The dynamic model of the clutch system is developed using MATLAB/Simulink, and evaluated by experimental data using a test rig. This performance simulator is useful to develop the clutch-by-wire (CBW) system for an automated manual transmission (AMT). The electro-mechanical type CBW system is also implemented as an automatic clutch for AMT. The prototype of CBW system is designed and implemented systematically, which is composed of an electric motor, worm gear and slider-crank mechanism. The test rig is developed to perform the basic function test of the automatic clutch, and the developed prototype is validated by the experimental data on the test rig.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.68-75
• /
• 2011

A vehicle fuel economy is very important issue in view of fuel cost and environmental regulation. It has been improved according to the performance improvement of the vehicle engine, power train and many components. It was evaluated at given mode (LA-4, FTP-75, etc) on an engine dynamometer or computer simulation program. In this paper, the fuel economy improvement cruise control algorithms as controling a vehicle velocity by road load calculated and predicted in a real expressway with gradient was studied. Firstly, the altitude and distance data which was measured with GPS sensor was already installed in the ECU of a vehicle. Then the vehicle equipped with GPS receiver is driven the same expressway. The ECU calculates the gradient angle and the in-/decreasing velocity using the gradient angle by comparing the current received distance and altitude data from GPS with the saved data ahead of the vehicle. Therefore the ECU can calculate and predict the vehicle velocity considering tolerance velocity of next position with running. Then the ECU controls the vehicle velocity to meet this predicted velocity in all section. Three cruise control algorithms with the different velocity profiles for the improvement of fuel economy are proposed and compared with the computer simulation results that the vehicle runs on Youngdong expressway. The proposed CVELCONT2 and CVELCONT3 algorithms were improved 3.7% and 4.8% of fuel economy compared with CONSTVEL which is steady cruising algorithm. These two algorithms are recommended as the Eco-cruise drive methodologies in this paper.

• Journal of Biosystems Engineering
• /
• v.38 no.4
• /
• pp.255-263
• /
• 2013

Purpose: It is not easy to drive a rice-transplanter avoiding underlapped or overlapped transplanting in paddy fields. An automated guidance system for the riding-type rice-transplanter would be necessary to operate the rice-transplanter autonomously or to assist the beginning drivers as a driving aid. Methods: A prototype of guidance system was composed of embedded computers, RTK-GPS, and a power-steering mechanism. Two Kalman filters were adopted to overcome sparse positioning data (1 Hz) from the RTK-GPS. A global Kalman filter estimated the posture of rice-transplanter every one second, and a local Kalman filter calculated the posture from every new estimation of the global Kalman filter with an interval of 200 ms. A PID controller was applied to the row-following mode control. A control method of U-turning mode was developed as well. A stepping motor with a reduction gear set was used to rotate the shaft of steering wheel. Results: Test trials for U-turning and row-following modes were done in a paddy field after some parameters have been tuned at the ground speed range of 0.3 ~ 1.2 m/s. The minimum RMS error of offset was 3.13 cm at the ground speed of 0.3 m/s while the maximum RMS error was 13.01 cm at 1.2 m/s. The offset RMS error tended to increase as the ground speed increased. The target point distance, LT also affected the system performance and PID controller parameters should be adjusted on different ground speeds. Conclusions: A target angle-based PID controller plus stationary steering angle controller made it possible for the rice-transplanter to steer autonomously by following a reference line accurately and even on U-turning mode. However, as condition in paddy fields is very complicated, the system should control the ground speed that prevents it from deviating too much due to ditch and slope.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.10
• /
• pp.1021-1028
• /
• 2011

The objective of this paper is to optimize the design parameters of a novel mechanism for a robotic knee orthosis. The feature of the proposed knee othosis is to drive a knee joint with independent actuation during swing and stance phases, which can allow an actuator with fast rotation to control swing motions and an actuator with high torque to control stance motions, respectively. The quadriceps device operates in five-bar links with 2-DOF motions during swing phase and is changed to six-bar links during stance phase by the contact motion to the patella device. The hamstring device operates in a slider-crank mechanism for entire gait cycle. The suggested kinematic model will allow a robotic knee orthosis to use compact and light actuators with full support during walking. However, the proposed orthosis must use additional linkages than a simple four-bar mechanism. To maximize the benefit of reducing the actuators power by using the developed kinematic design, it is necessary to minimize total weight of the device, while keeping necessary actuator performances of torques and angular velocities for support. In this paper, we use a SGA (Simple Genetic Algorithm) to minimize sum of total link lengths and motor power by reducing the weight of the novel knee orthosis. To find feasible parameters, kinematic constraints of the hamstring and quadriceps mechanisms have been applied to the algorithm. The proposed optimization scheme could reduce sum of total link lengths to half of the initial value. The proposed optimization scheme can be applied to reduce total weight of general multi-linkages while keeping necessary actuator specifications.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.1-18
• /
• 1995

This paper deals with the vibration absorbers of gravitational and centrifugal pendulum types for vibration controls of ship's substructures such as radarmasts, bridgewings and funnels. The mathematical model of such a vibrating system with an absorber is described as a 2 degree of freedom system and an efficient formulation for optimum design of the absorber is presented. For investigation applicability of the two types of the absorbers to a structure system, numerical calculations and experiments hove been performed with variation of mass ratios for each type. According to the results of investigations, the vibration absorber of gravitational type proved to be more useful and efficient than one of centrifugal pendulum type in a view point of mass ratio.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2237-2242
• /
• 2014

As Single households increases for reason of communication development, extending human life, there are many problems occuring all over the world. In order to solve this problem with an invasion of privacy and manintain a healthy life, this paper suggest non-contact type bio-signal measurement system using IR-Radar, displacement sensor and Pan-Tilt system. The proposed system can increse the distance of measured respiration from 1m to over 8m, which is comprised of two IR-Radar for location tracking, one displacement sensor for non-contact type bio-signal measurement and one stepping motor drive system. The proposed system is verified through experiments and were confirmed the possibility.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.8
• /
• pp.344-349
• /
• 2017

Wall-climbing robots have been developed for various purposes, such as cleaning skyscraper windows, maintaining large structures, and welding vessels. Conventional wall-climbing robots use movement systems based on wheels or legs. However, wheeled robots suffer from slipping effects, while legged systems require many actuators and control systems for the complex linkage structure, which also increases the weight of the robot. To overcome these disadvantages, we propose a new wall-climbing robot that walks based on gorilla locomotion. The proposed robot consists of a DC drive motor, a vacuum pump for adsorption, and a micro controller for controlling the system. The performance of the robot was experimentally verified on vertical and horizontal flat surfaces. The robot could be used for various functions in industrial sites or disaster areas.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.2
• /
• pp.190-198
• /
• 1995

Many industrial servo amplifiers employ power transister as output device. Thyristor converters are not adopted to drive servo motor, although thyristor is superior to power TR in power rating, noise immunity, price, and size. The reason is, thyristor has no ability of self turn - off. Here in this paper line commutation, in which thyristor is turned off naturally since cathode voltage is higher than anode as time goes by, is employed to turn on thyristor with a delicate sequence. We developed thyristor servo amplifier which does not cause any damage on thyristor because it is designed to prevent triggering the two SCRs in the same arm simultaneously. And it was made clearly how to trigger SCR without any power line shorting and also harmonic analysis is carried out with the aid of FFT analyzer and proved that it can be used even severe reactive load. The designed circuit operated as a good DC amplifier in conventinal servomotor and the results can be use as a position control system application.

• Fire Science and Engineering
• /
• v.26 no.4
• /
• pp.10-17
• /
• 2012

This study classifies the fire suppression measures implemented by wooden temples into four types according to availability of the pump trucks (water tanks) at the fire sites. And this study outlines the strategies and methods based on each type of fire suppression measure. The results show that the fire suppression strategy applied in general buildings is also employed in temples where pump trucks (water tanks) and fire-fighting water are available. For temples where trucks and water are not available, the helicopter, water bag, fire suppression strategy focused on water supply link, automatic transmission system of a fire engine's level by using radio communication network, and water bladder are used. In addition, general four-wheel-drive vehicles equipped with fire fighting tools such as motor pump, hose, nozzle, and water bladder should be deployed in fire stations around the temples. A fire suppression strategy using A-type ladders is also required.