• Magazine of the Korea Concrete Institute
• /
• v.6 no.2
• /
• pp.108-117
• /
• 1994

This study was performed to investigate the Alkali-Silica Reaction(ASR) of crushed stones using chemical analysis, polarization microscope, XRD, chemical method(KS F 2545, ASTM C 289), mortar-bar method( KS F 2546, ASTM C 227) and Scanning Electron Microscope (SEM ) and Energy Dispersive X-ray Analysis(EDXA) of reaction products by ASK in the mortar bars and to investigate the influence on alkali content and kind of added alkali to the ASR. Test results show that one kind of domestic crushed stone is estimated as deleterious by ASTM chemical method and mortar bar method, and reaction product is proved as alkali silicate gel by EDXA.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.363-368
• /
• 2000

This paper is an introduction of pessimum program for the identification of alkali-silica reaction of alkali-aggregate reaction which is known as one of a major factor of concrete deterioration. A series of gel-pat testing program was undertaken to observe the reactivity of potentially alkali-silica reactive concrete aggregates which were found to be reactive by previous petrographic examination (ASTM C 295). And then a pessimum program was performed in accordance with mortar-bar test method (ASTM C 227) with different percentage of those reactive components included in the fine aggregate source to determine the pessimum quantity. Chert and quartzite were found to be major components of reactive mineral/rock, and the pessimum condition for chert was about 3%, even though the test was performed with up to 25% of the component. In the case of quartzite, however, the mortar-bar expansion appeared to be directly proportional to the amount of quartzite sample with increasing tested quantity up to 35%. Both of the expansion results were well 3 and 6 month specified maximum limitation of 0.05% and of 0.1% respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.103-107
• /
• 1993

The Alkali Aggregate Reaction(AAR), reported first by T. E. Stanton in 1940, is a reaction between certain siliceous aggregate and hydroxyl ions present in the pore fluid of a concrete. The damage of concrete structures, deteriorated by AAR, have been reported since using the crushed stones caused by the exhaustion of natural aggregates. This study was performed to investigate the AAR of crushed stones using chemical analysis, polarization microscope, XRD, chemical method(KS F 2545, ASTM C 289), mortar bar method(KS F 2546, ASTM C 227) and Scanning Electron Microscope(SEM) and Energy Dispersive X-ray Analysis (EDXA) of reaction products by AAR in mortar bar.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.108-112
• /
• 1993

The term Alkali-Silica Reaction (ASR) is used to describe a reaction between certain siliceous aggregates and hydroxyl ions present in the pore fluid of a concrete. The ASR is affected by the content of alkali, the particle size and the content of reactive aggregate, water-cement ratio, humidity, temperature and so on. In this paper, the fluence of alkali content and kind of added alkali to the ASR was studied. As a result, the more the content of alkali was increased, the more the mortar-bar was expand and the expansion of mortar-bar was showed differently with the added alkali kinds, The reaction products by ASR were observed by SEM(Scanning Electron Microscope) and analyzed by EDXA(Energy Dispersive X-ray Analysis) also and showed a gel composed of alkali(Na+, K+), silica and calcium.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.145-149
• /
• 1995

This study is to recognize the effect of silica-fume, fly-ash, and chemical proportion in mortar that have salt on the inside affect steel bar corrosion. water-binder ratio, 0.5, compounds, each of 10, 15, 20% by weight of cement, Nacl mixing weight, 0.5, 1.0, 2.0% by weight of binder, The speciment is sealed and cured for 28days, the corrosion area ratio and weight reduction ratio is measured after the accelerated corrosion test of 20 cycles. The conclusion shows that there is no suppression effect of steel bar corrosion of silica-fume, fly-ash, in case of having salt on the inside.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.541-544
• /
• 2006

This study was performed to proof expansion effect of the mortar bar due to Alkali-silica Reaction (ASR) by ASTM C 1260 test. Recently, the failure case of cement concrete pavement by ASR was reported in Korea. Cement concrete structures are caused crack by ASR. The service life of cracked cement concrete structures by ASR will be shorted. In this study, crushed the slate rock producted Chungcheongnamdo Boryeong was caused 0.3% expansion at 14 days due to ASR by ASTM C 1260 test. The particular spectrum showed that the ASR gel was analyzed contents included Si, Na, K, and Ca by EDX (electron dispersive X-ray spectrometer). It was verified that the crushed aggregate was caused expansion by ASR in Korea.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.769-774
• /
• 2000

The purpose of this study was to investigate the structural performance of reinforcement corrosion reinforced concrete beams strengthened with epoxy mortar system. Main test parameters are existence and the magnitude of the reinforcement corrosion and the reinforcing bar and the tensile reinforcement ratio of the specimens. eight beam specimens were tested to investigate the effectiveness of each test variables on maximum load capacity and failure mode. Test results showed that the ultimate moment of th specimens were higher tan the nominal moment and the flexural stiffness was increased about 2.5 times and the cracking moments occurred over 60% of the failure moment in comparison with same sized control beam. However, note that epoxy mortar may conduct member into brittle failure mode.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.96-97
• /
• 2020

Polymer modified cement mortar (PCM) is commonly used as a repair material. However, in high-temperature environments such as fire, it is more likely to explode than cement mortar. The polymer is thermally decomposed at a high temperature to form a gas, and the gas remaining inside the structure increases the internal pressure to generate a burst. When an spalling occurs, the coating is peeled off and dropped, and high temperature is transmitted to the inside of the structure. In severe cases, even the reinforcing bar is exposed, which can lead to the collapse of the structural member due to severe loss of strength. In this study, in order to reduce spalling of PCM, a fiber mixing method was selected from the refractory method to find an appropriate blending ratio of fibers and polymers.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.4
• /
• pp.73-80
• /
• 2014

For the last decade many bridges and buildings have experienced flexural strengthening with the fiber reinforced polymer(FRP) bonding system, demands for increasing heavy traffic loads and the changing of the code application. Of the many strengthening systems, NSM(near surface mounted) system with FRP has become attractive and popular way of strengthening for the existed RC structures and many studies and applications of this technique have significantly increased all over the world. Meanwhile, polymer mortar that contains much of the same ingredients as cement but includes the addition of certain polymer resins for enhancing desired physical properties, has been used as an alternative adhesive. This paper focuses on flexural behaviour of CFRP-bar NSM system with variables such as kinds of adhesive, anchorage, sectional aspect ratio. Based on the test results and test-to-predicted ratio, this paper provides researchers and practical engineers a fundamental knowledge and intuition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.41-44
• /
• 2006

Increase in use of deck plates is accelerated by a manpower shortage and the high cost of construction. Some of problems including fire resistance, waterproof, and low corrosion can be solved by development of new deck plates. This paper evaluates the structural performance of the LAMO Deck which metal laths instead of galvanized steel sheet is covered by mortar.