• 한국유체기계학회 논문집
• /
• 제14권6호
• /
• pp.26-34
• /
• 2011

Waterhammer and slamming phenomena can occur when power is cut off due to reversal flow in pipeline and sudden close of check valve. Therefore analysis of reversal flow time, which means the time of reversal flow in pipeline due to pumping station blackout, is needed to protect facilities from waterhammer economically and efficiently. However systematic study on reversal flow time has not been done yet. So theory of reversal flow time analysis is proposed and verified with experiment using several parameters like pump specific speed, motor pole number, and characteristic curve of pipeline in this study.

• International Journal of Aeronautical and Space Sciences
• /
• 제1권2호
• /
• pp.22-29
• /
• 2000

A method to simulate the gas turbine transient behavior is developed. The basic principles of the method and main input data required are described. Calculation results are presented in terms of whole operating regime of the engine. The influence of initial parameters such as starting engine power, moment of inertia of the rotor, fuel schedule on performance characteristics of gas turbine during transient operation is shown. In addition, the effect of bleeding air on transient behavior is also considered. For validation of the developed computer code, a comparative analysis with experimental data obtained from a heavy duty gas turbine is made. Calculation results agree well with the experimental data for the range of operating regime studied and proved applicability of the developed technique to initial design stage of control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.473-473
• /
• 2000

This paper presents the 2-bit parallel algorithmic ADC using current mode for parallel method algorithm. It is operated by parallel conversion, 2-bit at each moment, and increase bit numbers by serial connection. The circuit operates in current mode. The comparison ratio can be controlled while working under mode operation. The circuit design used 0.8 ${\mu}{\textrm}{m}$ CMOS technology which capable to convert 2-bit in 50 ns, power consumed 0.786 nW, with input current 0-50 mA from 3V single supply. From simulation testing, the conversion rate is much faster than other method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.193-196
• /
• 2014

Experimantal evaluation of an energy storage device with high rotational speed to store regenerative energy which might be generated during the braking period of the trains is presented. The proposed ESS is small scale model and has 5kW output power, high rotational speed. In general railway trains generate regenerative energy for 10-20 sec when the train brakes and also high traction energy is needed for very short moment (10 sec) when the train increases the traction force. Considering such characteristics of the railway system energy storage device for the railway should have very fast response property. Among the various energy storage devices flywheel energy storage system has the fastest response property, which means that flywheel ESS is the most suitable for the railway system.

• 전기학회논문지
• /
• 제59권7호
• /
• pp.1265-1271
• /
• 2010

Power cable of an AC arc welder can surround a body of worker at the moment of welding. Applying the boundary element method, we calculated current densities induced in organs inside a worker to study the magnetic field reduction characteristics of shielding wear materials. We knew shielding wear with high permeability materials lowers current density more than high conductivity materials. We also found current density was lowest when high permeability materials were inside high conductivity materials in double layer shielding wear.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.508-512
• /
• 2004

An aerospace vehicle in flight can be exposed to random gust which may cause critical structural failure. In this paper, the failure analysis is conducted for composite wing subjected to random gust. For this, the profile of random gust is idealized as a stationary Gaussian random process and the power spectral density (PSD) of wing bending moment induced by gust is obtained. The PSD function is converted to probabilistic distributions and the failure probability during total flight time is calculated by Monte Carlo simulation.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.83-90
• /
• 2002

Prying action caused by the eccentric loads within the equipment itself and the anchors can result in a lack of adequate stiffness and strength within the equipment and in additional moment loadings on the anchors. A typical case of prying action often found in power plants is the angle type anchorage system with expansion bolt. Experimental and analytical studies were performed to investigate the relationship between the amplification factors and various geometrical and material factors. It is revealed that the value of the factor is effected by the stiffness of bolt and angle, lateral stiffness of cabinet, and geometrical parameter of anchor system.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권3호
• /
• pp.154-160
• /
• 2004

In this paper, a combined field orientation and adaptive backstepping approach using a sliding mode adaptive flux observer, is proposed for the control of induction motor In order to achieve the speed regulation with the consideration of improving power efficiency, rotor angular speed and flux amplitude tracking objectives are formulated. Rotor flux and inverse time constant are estimated by the sliding mode adaptive flux observer based on a fixed stator frame model and mechanical lumped uncertainty such as inertia moment, load torque disturbance, friction compensated by the adaptive backstepping based on a field-oriented model. Simulation results are provided to verify the effectiveness of the proposed approach.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.43-45
• /
• 2007

This Paper proposes a simple identification method of the moment of inertia for high performance spindle motor of machine tool. It uses the dynamic equation of a simple mechanical system, the torque reference of a speed controller, and the actual rotating speed of machine. The identified inertia can be for auto-tuning of the gains in the speed controller. The effectiveness of the proposed method is proved by the computer simulation.

• 한국가구학회지
• /
• 제13권2호
• /
• pp.39-52
• /
• 2002

The twenty-first century is era of cultural infrastructure during which cultural and economic power is greater than any other era in the fast, For this reason, all the countries in the world recognize that it is more important than any other things to plan to establish a structure which is suitable to the real conditions of a region in order to efficiently manage or operate their cultural environment. in particular, they think it is urgent that they should contrive to develop Their regional industries with new information media, introduction and spread of the up-to-date technique of design. However, our regional related industries very difficulty for the moment for them to apply new designing technique or to settle technical bottlenecks themselves. Accordingly, in order to resolve such a structural point at issue, this study has carried the newly designed and developed, 18 wooden, cultural craft items that were Produced by utilizing the ultramodern digital M/C installed at TIDIC (Tourism Industry Design Innovation Center in Kwangju University), it would contribute to achieve some global cultural products.