• 대한치과기공학회지
• /
• 제34권2호
• /
• pp.113-119
• /
• 2012

Purpose: Zirconia blocks for all ceramic dentures are divided into two groups. One is pre-heated block and the other is binder added block. In this study, the possibility of recycling the remained parts of binder added block after CAD/CAM machining with slip casting process was investigated. Methods: Owing to the binder added block contain large amount of organic matter, Binder burn-out was must be carried out before ball milling for preparing the casting slip. Binder burn-out was accomplished at $600^{\circ}C$ for 10 hours. Ball milling was performed with 5mm zirconia ball and 60mm polyethylene bottle. From 0% to 5% at 1% intervals of alumina was added to zirconia powder for preparing slip. Solid casting was achieved with plaster mold. Cast bodies were dried and sintered at $1,500^{\circ}C$ for 1 hour. Linear shrinkage, apparent porosity, water absorption, bulk density, and flexural strength were tested. Microstructures were observed by SEM, EDS and XRD analysis were executed. Results: Optimum slips for casting was prepared with 300g ball, 100g powder, and 180g distilled water. Cast body without alumina showed 26% of linear shrinkage, 6.07 of apparent density, and 470MPa of three point bend strength. On the other hand, as received zirconia block, which was sintered at the same conditions, showed 23% of linear shrinkage, 6.10 of apparent density, and 680MPa of three point bend strength. When 3% of alumina was added to zirconia, sintered body showed 23% of linear shrinkage, 6.10 of apparent density, and 780MPa of three point bend strength. SEM photomicrographs and EDS analysis showed alumina particles uniformly dispersed in zirconia matrix, and XRD analysis showed no phase transformation of tetragonal zirconia particles was occurred when alumina was added. Conclusion: According to the all of this experimental results, 3% of alumina added cast zirconia body showed excellent mechanical properties more than as received binder containing zirconia block.

• 한국주조공학회지
• /
• 제9권1호
• /
• pp.39-48
• /
• 1989

A basic three dimensional thermal model has been developed to simulate the solidification sequence for gravity die casting process. The finite difference method was used to analyze the solidification process during all the casting cycles. The prediction of die temperature in the quasi-steady state was analyzed by the boundary element method. The influence of die cooling on the heat flow in the cast/mold system was also investigated. Predictions of the computer simulation on temperature profiles and location of shrinkage defects were in good agreement with those observed in experimental die castings. Models of computer simulation which is developed by this work can be useful for the design and process control of die casting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.811-814
• /
• 1997

The injection molding process has been developed as a very important technology for the automotive and electric industries in recent years. But, in the injection molding products with rib-web structures, partial deformation by thermal volumetric shrinkage called Sink Mark, is occurred. In this study, to make explicitly characteristics of sink mechanism, an experimental approach was taken by using multi T-shaped mold cavity and FEM simulation. As a result, pressure on the packing process and the rib thickness are the most effective on sink mark depth. On the other hand, melt temperature has no effect on sink mark depth fot the same rib thickness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.812-815
• /
• 2000

Injection molding process was taken to manufacture DC motor case that surrounds DC motor used as automobile parts. Up to now, DC motor case has been made by the deep drawing process or bending process of metal materials. Simulations of filling, packing and cooling processes were done by CAE tool like Moldflow software. Optimal delivery system was decided from the analysis of flow balance, and packing and cooling analyses were performed by using the design of experiment to minimize the volumetric shrinkage of molded part and the temperature difference between mold and part.

• 대한기계학회논문집A
• /
• 제32권5호
• /
• pp.419-423
• /
• 2008

A new polymer replication technology using ultrasonic vibration is proposed and demonstrated. A commercial ultrasonic welder has been used in this experiment. Two different types of nickel molds have been fabricated: pillar type and pore type microstructures. Polymethyl methacrlylate (PMMA) has been used as the replication material and the optimal molding time was 2 sec and 2.5 sec for pillar-type and pore-type micromolds, respectively. Compared with the conventional polymer micromolding techniques, the proposed ultrasonic micromolding technique has the shortest processing time. In addition, only contact area between micromold and polymer substrate is melted so that the thermal shrinkage can be minimized. The fabricated PMMA microstructures have been very accurately replicated without vacuum. The proposed ultrasonic molding technique is a good alternative for high volume production.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.265-268
• /
• 2005

Thermoplastic elastormer (TPE) has many advantages such as high flexibility, high elasticity and high elongation, etc. TPE is easily molded such as plastic materials, therefore, many TPE parts are applied as home appliances and mechanical parts. However, if TPE is once molded, its mechanical properties are changed by injection molding conditions such as melt temperature, mold temperature, injection pressure and holding pressure, etc. In this study, the influences of the injection molding condition on the mechanical properties of thermoplastic vulcanizates(TPVs), which is one of the TPE, were investigated. By the injection molding experiment, as increasing the melt temperature, the tensile strength, shrinkage and hardness decreased. By the scanning electron microscope (SEM) analyzing the TPVs' crystallization, the morphology was affected by the melt temperature.

• 소성∙가공
• /
• 제13권3호
• /
• pp.236-241
• /
• 2004

UV-molded microlens arrays with high replication quality were fabricated using a parametric design method. It is important to maximize the replication quality, because one can obtain the replicated micro-optical components with desired properties by accurate control of the shape. In the present study, nickel mold inserts for microlens arrays with lenses having diameters between $3\mu\textrm{m}$ and $230\mu\textrm{m}$ were fabricated by electroforming process. An UV-molding system was designed and constructed, a simple technique to avoid micro-air bubbles was first suggested, and the effects of the compression pressure and UV-curing dose on the replication quality of UV-molded microlens arrays with a diameter of $14\mu\textrm{m}$ were examined experimentally. Finally, geometrical and optical properties of the replicated microlens arrays were measured and analyzed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.91-93
• /
• 2009

A large steel ingot needs to be larger and larger in size and an ultra high clean, no defect in quality with a low hot top ratio for the resent heavy industry. The demands are very difficult to achieve simultaneously because of their contradictive effect to each other in results. In this study, 30ton steel ingot was cast in a foundry with an optimized design parameter of cast mold and cast process conditions for the low hot top ratio, 12%. The cast ingot was analyzed in macro defect, segregations, and cleanness. No macro defect was founded in central surface of the ingot. The degree of segregation and cleanness are in the controlled range with a sound quality.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2021

In this study, we investigate the injection molding of f-theta lens, an important element of the laser scanning unit of laser printers and scanning systems. The f-theta lens is an aspherical plastic lens that must be molded with a precision of seconds. An injection molding method is often used for mass producing aspherical plastic lenses at a low cost. In the injection molding process, costs related to forming and injection are included. Therefore, in this study, to determine the shrinkage and deformation of injection molded f-theta lens, we predict the pressure and temperature distributions. Further, based on the analysis of the predictions, we maximize the design efficiency and verify the cost and development period reduction.

• 폴리머
• /
• 제36권6호
• /
• pp.677-684
• /
• 2012

사출성형공정은 고온으로 수지를 가소화시키고 고압으로 금형에 흘려 보내어 제품을 성형하는 방법이다. 이 과정에서 고분자 수지는 온도의 변화에 따라 수축을 하게 되는 성형수축이 발생된다. 그리고 시간이 흐른 뒤에도 제품에 변형이나 휨이 발생하게 되는데 이는 제품에 포함되어 있는 잔류응력의 이완 때문이다. 이러한 휨을 막기 위해 수지에 무기물을 첨가하여 수축을 줄이거나, 수지에 유리섬유나 카본섬유 등 섬유를 사용하여 휨의 저항성을 높인다. 그리고 성형품을 강건하게 설계하여 응력에 따른 휨의 저항을 향상시킨다. 본 연구에서는 강건설계를 위해 리브를 설치한 성형품에 나타나는 휨을 실험을 통하여 조사하였다. 성형조건에 따라서, 그리고 금형설계에 따라서 즉, 게이트의 위치에 따라서 휨의 변화를 조사하였다. 수지의 흐름방향과 흐름의 직각방형의 휨도 조사하였다. 게이트 근처와 게이트에서 먼 부분의 휨도 비교분석 하였다. 수지는 유리섬유로 보강된 결정성 수지인 PP와 PA66를 사용하였다. 유리섬유가 포함된 결정성 수지는 유리섬유가 포함된 비결정성 수지보다 휨이 컸다. 결정성 수지는 비결정성 수지에 비해 휨이 성형조건에 다소 적게 영향을 받았지만 제품의 설계에 따라서는 크게 변하였다.