• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.65-68
• /
• 2005

This paper investigated the engineering properties of cement mortar mixed with more than 2 kinds of sand. For fresh mortar properties, unit volume weight is constant regardless of mixing content and type of sand. An increase in contents of river and crushed sand resulted in an increase in flow, whereas an increase in recycled sand contents reduced flow. Gap between maximum flow in N3C0R0 and minimum flow in N0C0R3 exhibited about $12\%$. Compressive strength at 28 days ranged from 32 to 36 MPa in order for crushed sand, river sand and recycled sand. Mortar with mixed sand along with river sand and crushed sand showed compressive strength comparable to crushed sand. An increase of fraction of recycled sand in mixed sand resulted in a decrease in compressive strength. For drying shrinkage, N0C0R3 had the largest drying shrinkage among various mixture type. The combination of large contents of recycled sand and small contents of river and crushed sand had a large amount of drying shrinkage.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.124-133
• /
• 2003

Ti-25Al-xNb (x=0, 3, 7, 11, 13 at. %) alloys and 18 vol. % TiB/(Ti-25Al-11Nb) metal matrix composite were fabricated by spark plasma sintering process at 900-120$0^{\circ}C$. Microstructural characteristics of the sintered bodies were identified by SEM, EDX analysis, X-ray diffraction, and differential scanning calorimeterric method. $Ti_3Al$ alloy was consisted of equiaxed $\alpha_2$ phase. $Ti_3Al-Nb$ alloys and the matix of TiB/(Ti-25Al-11Nb) metal matrix composite had the morphology that O phase was precipitated at the grain boundary of $\alpha_2$phase. Volume fraction of O phase and hardness were depended on the concentration of Nb in $Ti_3Al-Nb$ alloy, Rule of mixing could be applied to hardness and Young's modulus of 18 vol. % TiB/(Ti-25Al-11Nb) metal matrix composite.

• Journal of the Korean Professional Engineers Association
• /
• v.19 no.1
• /
• pp.25-32
• /
• 1986

The number of visiters to Bukhan Mt. national park, generation quantity of solid waste and collection system were researched to consider a counterplan for the pollution control of the national park and study for developing the effective treatment of solid waste was tried through the proximate analysis of each component containing. Results obtained in this study were summerized as follows; The great part of visitors go on an excursion to the Bukhan Mt. national park during July and August and also, the solid waste was generated nearly a half of the total amount at the same period. The major collection facilities in the national park were waste basket and incineration box. But the incineration box was too large in volume and very far in distance, and its collection period was irregular, so it was cause to the congestion of solid waste and bad smell and dirty. Therefore, to complete collection of solid waste, we must set up the waste basket which able to find within 40～50m from the origination place of solid waste and induce the visitors to throw the solid waste. It was obtained as moisture content: 48.5 wt%, volatile solid: 28.4wt％, fixed solid: 23.1 wt％, lower heating value: 1,320kca1/kg from experimental analysis of solid waste. According to this analysis, the incineration operation is possible, but the generation quantity of solid waste was too small to construct incineration plant for heat recovery. It was found that it is suitable for the aerobic composting by mixing with the night soil which generate in the national park after the recovery of resources such as metals, glasses and plastics.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.2
• /
• pp.140-147
• /
• 2004

An aqueous solution of a commercial liquid synthetic detergent for kitchen use was photodecomposed in the presence of titanium dioxides powder under an atmosphere of air at room temperature. Titanium dioxides were prepared by sol-gel method from titanium iso-propoxide at different R ratio($H_2O$/titanium iso-propoxide) and calcined at $500^{\circ}C$. All titanium dioxides were characterized by XRD, BET surface area analyzer and UV-VIS spectrometer. The surface area of titanium dioxides prepared at R ratio=6 appeared higher volume about 20% than commercial $TiO_2$ catalysts. XRD patterns of titania particles were observed mixing phase together with rutile and anatase type. Titanium dioxides prepared by sol-gel method show higher activity about 6% than commercial $TiO_2$ catalysts on the photocatalytic degradation of a commercial liquid synthetic detergent for kitchen. The concentration of the detergent decreased to about 90% of its initial value at illumination times of 2 hour. Illumination for 30 minutes decreased the concentration of oxygen to about one-fifth of the initial value.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.6.1-6.1
• /
• 2011

Nanoscale block copolymer (BCP) patterns have been pursued for applications in sub-30 nm nanolithography. BCP self-assembly processing is scalable and low cost, and is well-suited for integration with existing semiconductor fabrication techniques. However, one of the major technical challenges for BCP self-assembly is limited tunability in pattern geometry, dimension, and functionality. We suggest methods for extending the degree of tunability by choosing highly incompatible polymer blocks and utilizing solvent vapor treatment techniques. Siloxane BCPs have been developed as self-assembling resists due to many advantages such as high etch-selectivity, good etch-resistance, long-range ordering, and reduced line-edge roughness. The large incompatibility leads to extensive degree of pattern tunability since the effective volume fraction can be easily manipulated by solvent-based treatment techniques. Thus, control of the microdomain size, periodicity, and morphology is possible by changing the vapor pressure and the mixing ratio of selective solvents. This allows a range of different pattern geometry such as dots, lines and holes and critical dimension simply by changing the processing conditions of a given block copolymer without changing a polymer chain length. We demonstrate highly extensive tunability (critical dimension ~6~30 nm) of self-assembled patterns prepared by a siloxane BCP with extreme incompatibility.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.285-288
• /
• 2008

The Present Study describes the numerical investigations concerning a fuel(Hydrogen), inert gas (Nitrogen) or supersonic air stream issued between each other. The basic flow configuration consists of a plane, double shear/mixing layer flow. For the numerical solution, a fully conservative unsteady $2^{nd}$ order time accurate sub-iteration method and a $2^{nd}$ order Total Variation Diminishing(TVD) scheme are used with the finite volume method(FVM). The results are consist of three categories ; single shear layer consist of fuel and supersonic air stream, inert gas stream issued between supersonic air and fuel stream, fuel gas stream issued between supersonic air and fuel stream. The numerical calculations has been carried out in case of 1,2, and 4mm thickness of center stream. The width of total gas stream is 4cm.

• YAKHAK HOEJI
• /
• v.1 no.1
• /
• pp.1-2
• /
• 1948

The finely powdered entire harbs of Polygala japonica Houttuyn, a drug known as Yong Shin-Cho in Korea, were boiled with methanol and from the filtered extract the methanol was distilled off under diminished pressure and the aqueous solution of the residue was evaporated to dryness after being mixed with ignited magnesia. The dried mass was boiled with absolute alcohol, the filtered clear liquid was evaporated to a small volume and the precipitate Saponin produced by mixing with ether was filtered off. When the filtrate was again evaporated to the thickness of a syrup and allowed to cool for a few days in an ice box, crystalls were separated out in about 5% yield, which formed colorless columns, M. P. 142.deg., from methanol and had the formula $C_{6}$ $H_{12}$ $O_{5}$. On heating it with acetic acid anhybride and sodium acetate, its tetraacetyl derivative $C_{6}$ $H_{8}$ $O_{5}$(C $H_{3}$CO)$_{4}$ was obtained and which formed colorless needles, M. P. 62-5.deg., from ethanol. Their melting points, results of elementar analysis and other characteristics agreed with that of Polygalitol and its derivative. Finally they were proved to be identical with Polygalitol and its derivative, respectively, through determination of mixed melting points with the samples. Polygalitol was isolated from several plants of genus polugala e. g. P. amara, P. vulgaris, P. teunifolia, P. senega etc. The authors added to them another instance of identifying Polygalitol from the plant of genus polygala.olygala.

• Journal of Environmental Health Sciences
• /
• v.33 no.5
• /
• pp.462-469
• /
• 2007

Isolation and application of oil-degradation microbes from the oil-contaminated soil and the determination of optimal operation conditions about the peat moss, the addition for the oil-biodegradation. After all experiments, we have acquired three important conclusions: First, we found out the 4 microbes, Pseudomonas fluorescens, Pseudomonas aeruinosa, Kurtia sp., Bacillus ceres, with excellent capability for the oil-degradation; Second, the optimal operating conditions of the peat moss for TPH treatment were pH $7{\sim}8$, temperature $25{\sim}30^{\circ}C$, water content 20%, mixing 2 times/ day, addition volume 2%; Third, in case of the application to the oil-contaminated soil with 4 mixed microbes, the removal efficiency of TPH was increased from 54% to 83% in oil-contaminated soil and from 65% to 85% in oil-contaminated soil with the peat moss.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.2
• /
• pp.113-123
• /
• 2015

The efficiency of the ventilation system is a key point for durable and reliable electric generators. The design of such system requires a detailed understanding of the air flow in the generator. Computational fluid dynamics (CFD) has the potential to resolve the lack of information in this field. The present work analyses the air flow inside a generator model. The model is designed using a CFD-based approach, and manufactured by taking into consideration the experimental and numerical requirements and limitations. The emphasis is on the possibility to accurately predict and experimentally measure the flow distribution inside the stator channels. A major part of the work is focused on the design of an intake and a fan that gives an evenly distributed flow with a high flow rate. The intake also serves as an accurate flowmeter. Experimental results are presented, of the total volume flow rate, the total pressure and velocity distributions. Steady-state CFD simulations are performed using the FOAM-extend CFD toolbox. The simulations are based on the multiple rotating reference frames method. The results from the frozen rotor and mixing plane rotor-stator coupling approaches are compared. It is shown that the fan design provides a sufficient flow rate for the stator channels, which is not the case without the fan or with a previous fan design. The detailed experimental and numerical results show an excellent agreement, proving that the results reliable.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.29-32
• /
• 2004

This work was devoted to an investigation of etching mechanisms for $(Ba,Sr)TiO_3$ (BST) thin films in inductively coupled $CF_4/Ar$ plasma. We have found that an increase of the Ar content in $CF_4/Ar$ plasma causes non-monotonic behavior of BST etch rate, which reaches a maximum value of 40 nm/min at 80% Ar. Langmuir probe measurements show a weak sensitivity of both electron temperature and electron density to the change of $CF_5/Ar$ mixing ratio. O-D model for plasma chemistry gave monotonic changes of both volume densities and fluxes for active species responsible for the etching process. The analysis of surface kinetics confirms the possibility of non-monotonic etch rate behavior due to the concurrence of physical and chemical pathways in ion-assisted chemical reaction.