• KCI Concrete Journal
• /
• 제11권3호
• /
• pp.79-88
• /
• 1999

Most difficulties of inducing high fluidity on the concrete mixing design with a strength range of 210 to 240kg/$\textrm{cm}^2$ result from the segregation of aggregates due to the shortage of cementitious binders. To solve the problem, this study concentrated on finding the optimized amount of binder material which does not affect the concrete strength and is also economical. Also there were studies on the use of intermediate sized aggregates to avoid the gap-grading between coarse and fine aggregates so that the material segregation in high flowing concrete was and minimalized the fluidity and penetration capacity of the reinforcing bars was enhanced. Throughout the parametric study with respect to water/binder ratio. superplasticizer. replaceable mineral admixture, the size of coarse aggregate and mixing methods, the effect of each constituent on the characteristics of high flowing concrete could be observed. As a result or partially using stone powder or an intermediate class of aggregate (max. diameter 13mm) . it was fund that the fluidity of concrete significantly increased without material segregation and any change of compressive strengths. It was also proved in this study that proper mixing time and speed are significant factors influence the performence of high flowing concrete.

• 대한의용생체공학회:의공학회지
• /
• 제17권4호
• /
• pp.499-506
• /
• 1996

Blood flow velocimeter is an essential device to measure the blood flow in skin tissue. In this study, we developed a high-speed LDV(laser Doppler Velocimeter) that has real time processing capability using a DSP(digital signal processing) chip and is able to continuously measure information about blood-flow based on a noninvasive method using self-mixing type laser diode. This LDV system has a simpler structure than any other typical blood flow velocimeter and is composed of new self-mixing probe, stabilizer circuits DSP board, and interf'ace boule We measured velocity of speaker-unit by operational frequencies to identify Doppler effect of this system, performed clinical experiment on bare finger tip and compared it with a commercial euipment BPM403A(USA).

• 한국유체기계학회 논문집
• /
• 제15권5호
• /
• pp.32-36
• /
• 2012

The positive displacement pump and the regenerative pump are widely used in the range of low specific speed, $n_s{\leq}100$[rpm, m3/min, m]. The positive displacement pump is not suitable for miniaturization and operation in high rotational speed. The regenerative pump has a problem with large leakage flow and low efficiency. While the centrifugal pump has advantages of high efficiency, miniaturization and high rotational speed, efficiency drops sharply with decrease in specific speed. Therefore the purpose of this study is to design a new type of centrifugal pump that has advantages of centrifugal pumps in operation in low specific speed. The name of this new type of pump was called 'Pipe type centrifugal pump', since the flow path through the impeller is simple circular pipe. Due to the simple shape of impeller, the manufacturing process is simple and cost is low. There is strong jet flow at the outlet of the impeller. This jet induces flow path loss, meridional dynamic pressure loss and mixing loss. Large disk friction makes the efficiency be limitted in the range of low specific speed. Even though the loss and the low efficiency, 'Pipe type centrifugal pump' represents stable performance, affordable pressure ratio and efficiency better than that of other low specific speed pumps.

• KSBB Journal
• /
• 제30권6호
• /
• pp.307-312
• /
• 2015

Transgenic rice cells using RAmy3D promoter can provide high productivity, and the production of recombinant protein is induced by sugar starvation. In this system, productivity was reduced during the scale-up processes. To ensure the influences of shear stress and oxygen transfer rate, working volume and mixing performances were investigated under various agitation speeds and working volumes. In addition, inoculation methods including suspended cells and filtered cells were compared. Working volumes and shaking speeds were 300, 450 mL and 80, 120 rpm, respectively. Hydrodynamic environment of each condition was measured numerically like mixing time and $k_La$. Good mixing performance and high shear stress were measured at high agitation speed and low volume. The highest level of hCTLA4Ig was 30.7 mg/L at 120 rpm, 300 mL. When conditioned medium was used for inoculation, increased cell growth was noticed during the day 0~4 and decreased slower than filtered cells. Compared with filtered cells, the maximum hCTLA4Ig level reached 37.8 mg/L at 120 rpm, 300 mL and lower protease activity level was observed. In conclusion mixing performance is critical factor for productivity and conditioned medium can have a positive effect on damaged cells caused by hydrodynamic shear stress.

• Composites Research
• /
• 제29권4호
• /
• pp.223-229
• /
• 2016

SiC 나노입자는 고분자 수지의 굴곡특성을 강화하기 위해 사용된다. 본 연구는 대용량 SiC 나노입자가 함유된 에폭시 수지를 제조하고 분산도를 평가한 것에 관한 내용이다. SiC 나노입자를 혼합하는 과정에 교반기와 초음파 분쇄기를 동시에 사용하여 20 wt%의 SiC 나노입자 강화 에폭시 복합재료를 제조하였다. 교반기와 분쇄기를 동시에 이용하는 방법으로 분산속도와 분산도가 개선됨을 기계적 물성 평가와 FE-SEM 결과로 확인하였다. 이러한 결과로 SiC 나노입자의 분산 모델을 구축하였다. 궁극적으로, 탄소섬유(UD 타입)와 20 wt% SiC 나노입자 강화 에폭시 수지를 사용하여 복합재료를 제조하였다. 교반기와 분쇄기를 동시에 사용했을 경우 초음파 분쇄기만 이용했을 경우에 비해 우수한 복합재료의 물성을 나타내었다.

• 한국도로학회논문집
• /
• 제9권4호
• /
• pp.171-184
• /
• 2007

화학적 첨가제를 이용한 안정처리는 지반의 강도증가 및 변형발생을 제어하기 위한 방법으로 깊은 심도까지 광범위하게 적용되어 지고 있다. 화학적 안정처리의 기본목적은 지반의 강도증가, 압축성 감소, 팽창특성 등을 개선하여 지반의 내구성을 증가시키는 것이며, 최근 들어 환경친화적이며 혼합체의 특성 및 혼합속도를 효율적으로 개선한 다양한 형태의 진보적인 시멘트 혼화재가 개발되고 있다. 본 연구에서는 농어촌도로(농도)의 효율적인 포장공법 개발을 위하여 시멘트혼화재를 활용하는 방안을 연구하였으며, 혼화재 종류 및 배합비에 따른 다짐시험, 일축압축강도시험, 동결융해시험 및 휨강도시험을 실시하였다. 본 연구결과에 따르면, 실트질 원지반토가 점토지반에 비해 강도증가 및 동결융해특성이 우수하며, 액상형 시멘트 혼화재가 분말형태 보다 효과적인 것으로 나타났다. 또한 저배합에서도 고강도의 품질을 발휘하여 농어촌도로 표층 내구성 저하를 개선할 수 있을 것으로 판단된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.287-292
• /
• 2001

Under the condition of variable density and specific heat, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the condition of variable density and specific heat play important roles in determining friction and load of journal bearing at high speed operation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.484-487
• /
• 1995

An interacting multiple model (IMM) approach which merges two hypotheses for the situations of constant speed and constant acceleration model is considered for the tracking of maneuvering target. The inflexibility of uncertainty which lies in the kinematic constraint (KC) represented by pseudomeasurement noise variance is compensated by the mixing of estimates from two model Kalman tracker: one with KC and one without KC. The numerically simulated tracking performance is compared for the "great circular like turning" trajectory maneuver by the single model tracker with constant speed KC and two model tracker which is developed in this paper.his paper.

• 한국건설순환자원학회논문집
• /
• 제11권3호
• /
• pp.244-250
• /
• 2023

본 논문에서는 타피오카 전분이 모르타르에 미치는 영향을 평가하기 위하여 타피오카 전분을 혼합한 모르타르를 제조하였으며, 모르타르의 품질특성 평가를 통하여 타피오카 전분이 모르타르의 성능개선 및 기초품질 향상에 미치는 영향을 검토하였다. 타피오카 전분은 모르타르에 혼합할 경우 굳지않은 모르타르의 반죽질기의 점성을 증가시켜 플로우가 감소하는 경향이 있었으며, 타피오카 전분 혼합율 0.025 % 증가에 따라 약 10 % 감소하였다. 또한 타피오카 전분이 모르타르의 압축강도에 미치는 영향은 재령 28일의 경우 타피오카 전분 혼합에 관계없이 동등 수준으로 나타났지만 재령 3일의 초기재령에서는 타피오카 전분 혼합에 따라 강도발현 속도가 촉진되는 것으로 나타났으며, 타피오카 전분 혼합율 0.050 % 혼합할 경우 약 20 %의 최대 초기재령 압축강도 발현이 나타났다. 부착강도는 타피오카 전분 혼합율 0.050 % 혼합할 경우 부착강도가 약 60 % 향상되었으며, 길이변화는 최종 수축량이 5 % 감소하는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제23권5호
• /
• pp.207-218
• /
• 2007

Turbocharger bearings are under the circumstance of high temperature, moreover rotated at high speed. It is necessary to be designed overcoming the high temperature. So the type of oil inlet port, the inlet oil temperature and the sort of engine oil should be designed, controlled and selected carefully in order to reduce the bearing inside temperature. In this study, the influence of aerated oil on a high-speed journal bearing is also examined by using the classical thermohydrodynamic lubrication theory coupled with analytical models for viscosity and density of air-oil mixture in fluid-film bearing. Convection to the walls and mixing with supply oil and re-circulating oil are considered. The considered parameters for the study of bubbly lubrication are oil inlet port's type, oil aeration level and shaft speed. It is found that the type of oil inlet ports and shaft speed play important roles in determining the temperature and pressure distribution, then the friction in a journal bearing at high speed operation. Also, the results show that, under extremely high shaft speed, the high shear effects on aerated oil and the high temperature effects are canceled out each other. So, the bearing load and friction show almost no difference between the aerated oil and pure oil.