• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.76-86
• /
• 1994

Combustion of diesel engine depends on the mixing of air and evaporating fuel during ignition delay greatly. Variation of air-fuel mixing rate and ignition delay for engine operating condition causes difference of combustion, performance and exhaust emissions. This study is investigated in a turbocharged diesel engine of IDI swirl chamber type. In the results, As injection timing is advanced until $12.6^{\circ}$ BTC, ignition delay decreases. NOx concentration and smoke level in exhaust gas increases for advanced injection timing Ignition delay, combustion period, pressure rise rate and exhaust gas temperature are increased with increasing engine speed. And ignition delay at high load is more decreased than that at low load. Ignition delay and combustion period are decreased with increasing intake pressure. Power increases, temperature and CO, NOx concentration in exhaust gas decreases as intake pressure increases. With increasing load, ignition delay is decreased and combustion period, motoring pressure are increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.328-331
• /
• 2000

Carbon nanotube(CNT) was successfully grown on Ni-W alloyed substrate by applying PECVD technique(Plasma Enhanced Chemical Vapor Deposition). As a catalyst, Ni-W alloyed substrate was prepared by mechanical alloying method. In order to find the optimum growth condition, initially two different types of gas mixtures such ac $C_2$H$_2$-H$_2$and $C_2$H$_2$-MH$_3$were systematically investigated by adjusting results on the mixing ratio in temperature range of 500 to 80$0^{\circ}C$. In this work, we will report the preliminary results on the CNT processed by PECVD, which were characterized by XRD, SEM and TEM. Finally we will evalute the effect on CNT growth by changing many processing parameters, such as typical gas, mixing ratio between 2 mixture, plasma power and etc.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.353-356
• /
• 2008

The effects of design parameters of supersonic ejector system under the assumption of constant pressure mixing; such as mass flow rate ratio, area ratio, Primary mach number on ejector system performance were investigated by theoretical formulations. And for a given design condition and working fluid, Computational Fluid Dynamics was conducted.

• Korean Journal of Materials Research
• /
• v.32 no.4
• /
• pp.223-229
• /
• 2022

A porous photocatalyst concrete filter was successfully produced to remove NOx, by mixing TiO₂ photocatalyst with lightweight aerated concrete. Ultra Fine Bubbles were used to form continuous pores inside the porous photocatalytic concrete filter, which was mixed via a bubble generation experiment. The optimal mixing condition was determined to be with 4 % of the bubble generation agent B. NO removal specimens were prepared for various photocatalytic loading conditions, and the specimen containing 3 % P-25 removed NO at a concentration of 1.03 µmol in 1 h. The NO removal rate of the porous photocatalytic concrete filter prepared in this study was 10.99 %. This photocatalytic filter performance was more than 9 times the amount of NO removed by a general photocatalytic filter. The porous photocatalyst concrete filter for removing NOx developed in this study can be applied to various construction sites and the air quality can be solved by reducing NOx contributing to the formation of fine particles.

• Journal of Korean Port Research
• /
• v.9 no.1
• /
• pp.65-72
• /
• 1995

This study is being done for the purpose to achieve a stable demand and supply of materials for long term. The author investigated condition of suitable mixer design method for concrete, an individual value and a character of dynamics as a supplement material by drying up the natural aggregate, and a possible practicalization plan to reduce defects to the minimum. As a result of this study, it can be acquired a good quality of concrete by the use of the natural sand (Nak Dong river sand) and the crushed sand with suitable mixing ratio. The fineness modulus (F.M) of mixing aggregate is $2.7\pm1$ at this time and this is good for workbility and plasticity of concrete.

• Journal of Korean Society on Water Environment
• /
• v.23 no.1
• /
• pp.81-86
• /
• 2007

This paper describes a study on the role of limestone which might affect the dissolution of phosphates when phosphate containing sediments are put under anaerobic conditions. A small quantity of calcium hydroxy-apatite, alone or mixed with limestone powder, was put in contact with aqueous solution of acetic acid or carbonic acid, and variations of phosphate concentration were determined time dependantly. The results showed that the concentration was remarkably low in the presence of limestone, signifying that the coexistence of limestone suppresses the dissolution of phosphate by organic acid and/or carbonic acid. Separate experiments conducted by developing an anaerobic condition, after mixing lake sediments with dried leaves and limestone, showed that the existence of limestone suppressed the dissolution of phosphate. These results show that the application of limestone might be a useful measure to prevent deterioration of water quality originated from eutrophication by inhibiting the internal loading of P in eutrophic water-bodies.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.137-144
• /
• 2007

Sintering condition and various chemical composition of bond materials for micro-blades were studied. The methods mixing of pure powders and using pre-alloyed powders for compaction and sintering were compared and optimized in terms of the evaluation of bending strength and fractographic study. The effect of the amount of graphite as a lubricant and diamond abrasive on the strength of sintered bond materials and fracture toughness was investigated. The strength decreased with increasing the amount of graphite and diamond abrasive.

• Journal of the Korean Ceramic Society
• /
• v.40 no.2
• /
• pp.132-138
• /
• 2003

The effect of synthesis condition, type of starting materials, mole ratio, mixing. aging, and crystallization temperature and time, on the size of FAU-type zeolite has been studied. Different mixing route may lead to the different phase of zeolite even with the same starting materials. In general, the size of particles is smaller after aging, especially at lower aging temperature. Two step mixture gel preparation method resulted to not only the reduction of crystallization time but also that of particle size, but without the aging of two mixture gels before the preparation of the overall gel in the second step, only the crystallization time was reduced, not the particle size. The FAU-type zeolite with average particle size 0.4$\mu$m and BET surface area 838 $m^2$/g was obtained from starting materials of liquid sodium silicate, sodium aluminate, and sodium hydroxide with two step preparation of mixture gel, aging of the mixture gels in two steps, which effectively reduced the crystallization time and particle size.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.2
• /
• pp.107-116
• /
• 2017

When drilling operation is being performed, many physical and chemical changes are occurred near wellbore. To handle various changes of well condition and keep drilling process safe, additives of bulk, such as bentonite for increasing density of drilling mud, barite for increasing viscosity of drilling mud, polymer for chemical control, or surfactant, are added into drilling mud through a mud shear mixer. Because the achievement of the required material property through mud mixing system is essential to stabilize drilling system, it is of importance to analyze multi-phase flow during mud mixing process, which is directly related to increase mixing performance of the system and guarantee the safety of the whole drilling system. In this study, a series of liquid-solid flow simulation based on a computational fluid dynamics (CFD) are performed with comparing to solid concentration in experiment by Gilles et al. [2004] to understand the characteristics of liquid-solid mixing in a mud shear mixer. And then, the simulation-based design of shear mixer are carried out to improve mixing performance in a mud handling system.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.10
• /
• pp.39-49
• /
• 2018

In this study, aimed at determining the elastic modulus of deep mixed samples, 320 test specimens were developed by mixing 8%, 10%, 12%, and 14% of stabilizer mixture in the granular conditions of clay, sand and gravel. Uniaxial compression tests were carried out using these specimens, and the uniaxial compression strength and strain were analyzed to determine the secant elastic modulus and tangent elastic modulus. Laboratory test results showed that the uniaxial compression strength of all deep mixed samples increased with increasing curing time and stabilizer mixing ratio, and that the secant elastic modulus and the tangen elastic modulus also increased. The increase of the elastic modulus according to the curing period turned out greater in the tangent elastic modulus than in the secant elastic modulus. In order to measure elastic modulus with changes in stabilizer mixing ratio, the correlation coefficient between the elastic modulus for stabilizer mixing ratio of 8% and that of 10%, 12% and 14% was calculated respectively by the specimen condition. The elastic modulus tended to increase as the grain size in a deep mixed specimen increased. The distribution of grain size that had the greatest effect appeared when the composition ratio of sand was high. On the other hand, the increase in the elastic modulus was larger in the sand specimens than in the clay and gravel specimens. Based on these results, it is suggested that a pertinent soil parameter of the deep mixed ground in the field may be obtained by the particle size distribution and the mixing ratio of stabilizer of the deep mixed soil.