• 한국축산시설환경학회지
• /
• 제12권1호
• /
• pp.41-44
• /
• 2006

2중필름 온실계사에서 육계를 사육하였을 때 발생하는 계분을 처리할 수 있는 수동 교반형 퇴비화시스템을 개발하였으며, 교반빈도가 퇴비화 온도에 미치는 효과를 분석하였다. 병원균 사멸에 필요한 $55^{\circ}C$ 이상의 온도를 유지한 기간은 무교반에서 88시간 1회/4일의 교반에서는 179 시간, 1회/2일의 교반에서는 200 시간으로 교반회수가 빈번할수록 그 기간이 길어지는 것으로 나타났다.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.687-696
• /
• 2007

To increase the reliability of auto-ignition in CAI engines, the thermodynamic properties of intake flow is often controlled using recycled exhaust gases, called internal EGR. Because of the internal EGR influence on the overall thermodynamic properties and mixing quality of the gases that affect the subsequent combustion behavior, optimizing the intake and exhaust valve timing for the EGR is important to achieve the reliable auto-ignition and high thermal efficiency. In the present study, fully 3D numerical simulations were carried out to predict the mixing characteristics and flow field inside the cylinder as a function of valve timing. The 3D unsteady Eulerian-Lagrangian two-phase model was used to account for the interaction between the intake air and remaining internal EGR during the under-lap operation while varying three major parameters: the intake valve(IV) and exhaust valve(EV) timings and intake valve lift(IVL). Computational results showed that the largest EVC retardation, as in A6, yielded the optimal mixing of both EGR and fuel. The IV timing had little effect on the mixing quality. However, the IV timing variation caused backflow from the cylinder to the intake port. With respect to reduction of heat loss due to backflow, the case in B6 was considered to present the optimal operating condition. With the variation of the intake valve lift, the A1 case yielded the minimum amount of backflow. The best mixing was delivered when the lift height was at a minimum of 2 mm.

• 한국추진공학회지
• /
• 제14권5호
• /
• pp.92-100
• /
• 2010

75톤급 기술검증용 연소기의 연소안정성 시험이 저압 조건에서 수행되었다. 이 시험에 사용된 두 개의 연소기 헤드 중 하나는 631개의 분사기를 가지며, 다른 하나는 721개의 분사기를 가진다. 631개의 분사기를 갖는 연소기 헤드는 연소압력 30 bar에서 자발 불안정이 발생하였고 721개의 분사기를 갖는 연소기 헤드는 동일한 연소압력과 동일한 유량 조건에서 고주파 연소안정성이 유지됨을 보였다. 그러나 721개의 분사기를 갖는 연소기 헤드는 연소압력 20 bar에서 자발 불안정이 발생하였고 이러한 결과로부터 연소기 헤드의 형상은 안정성 경계 영역을 변화시킴을 알 수 있었다.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.630-638
• /
• 2010

The present investigation has been performed on the mixing behavior and microstructural development during fabrication of Fe micro-nano powder feedstock for a micro-powder injection molding process. The mixing experiment using a screw type blender system was conducted to measure the variations of torque and temperature during mixing of Fe powder-binder feedstock with progressive powder loading for various nano-powder compositions up to 25%. It was found that the torque and the temperature required in the mixing of feedstock increased proportionally with increasing cumulative powder loading. Such an increment was larger in the feedstock containing higher content of nano-powder at the same powder loading condition. However, the maximum value was obtained at the nano-powder composition of not 25% but 10%. It was owing to the 'roller bearing effect' of agglomerate type nano-powder acting as lubricant during mixing, consequently leading to the rearrangement of micro-nano powder in the feedstock. It is concluded that the improvement of packing density by rearrangement of nano-powders into interstices of micro-powders is responsible for the maximum powder loading of about 71 vol.% in the nano-powder composition of 25%.

• 대한수학회지
• /
• 제45권4호
• /
• pp.1101-1111
• /
• 2008

Under the condition of h-integrability and appropriate conditions on the array of weights, we establish complete convergence and strong law of large numbers for weighted sums of an array of dependent random variables.

• 대한전자공학회논문지
• /
• 제27권8호
• /
• pp.1289-1293
• /
• 1990

In this paper, the oscillation condition for the linear phase-conjugate oscillator which consists of one photorefractive crystal, two conventional mirrors, and two pump waves applied externally has been analyzed. In the result, it has been shown that the oscillation condition of this oscillator can be easily controlled by adjusting the various parameters such as the intensity ratio, polarization states, and light path difference of two pump waves, etc.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.19-24
• /
• 1995

Most difficulties in inducing high flowability of general strength concrete arise from the segregation of aggregates due to the shortage of cementatious binders. To solve the problem, our research team has concentrated on finding the binders to link a gap between coarse and fine aggregates, under the condition not to influence a concrete strength. As a result of using stone powder or a middle class of aggregate size mostly used for asphalt pavement(Max. dia 13mm), we found that flowability of concrete increased significantly without aggregation and decrease of compressive strength.

• Tribology and Lubricants
• /
• 제17권4호
• /
• pp.297-306
• /
• 2001

Under the condition of variable density and specific heat, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined within some degree of Journal misalignment. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the condition of variable density and specific heat play important roles in determining friction and load of Journal bearing at high speed operation.

• 대한수학회지
• /
• 제35권2호
• /
• pp.433-447
• /
• 1998

We investigate coboundary conditions for two functions defined on a mixing subshift of finite type to have the same Gibbs measure. Also we find conditions for a function to be a coboundary.

• Communications for Statistical Applications and Methods
• /
• 제20권4호
• /
• pp.339-345
• /
• 2013

In this paper, we give a tractable sufficient condition for functional central limit theorem to hold in Markov switching ARMA (p, q) model.