• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.178-185
• /
• 2005

Crack tip displacement is originated by tensile stress component, s and shear stress component, t on pure Mode I and pure Mode II. The crack tip displacement(CTD) depends on combined types of different two stress components under mixed-mode loading conditions (MMLC). Thus, the analysis of crack tip displacement must be CTD vector, dv which is composition of ds and dt under MMLC. In this paper, various effects of MMLC on the crack closure are studied experimentally. The crack closure magnitude is calculated from the information of crack tip displacement under MMLC. This information has been obtained from the high resolution optical microscope in direct observations of crack displacement behavior at the crack tip. Observed crack tip displacement is analyzed by using CTD vector to determine crack opening load. The various effects of MMLC on the crack closure are explained using crack opening ratio with crack length and mode mixture. The effective stress intensity factor considering crack closure is also discussed.

• Smart Structures and Systems
• /
• 제14권5호
• /
• pp.869-881
• /
• 2014

This paper presents the materials analysis for combination of working modes of Magnetorheological (MR) damper. The materials were selected based on the optimum magnetic field strength at the effective areas in order to obtain a better design of MR damper. The design of electromagnetic circuit is one of the critical criteria in designing MR dampers besides the working mechanism and the types of MR damper. The increase in the magnetic field strength is an indication of the improvement in the damping performance of the MR damper. Eventually, the experimental test was performed under quasi-static loading to observe the performances of MR damper in shear mode, squeeze mode and mixed mode. The results showed that the increment of forces was obtained with the increased current due to higher magnetic flux density generated by electromagnetic coils. In general, it can be summarized that the combination of modes generates higher forces than single mode for the same experimental parameters throughout the study.

• Composites Research
• /
• 제23권4호
• /
• pp.21-27
• /
• 2010

대부분의 구조물 파괴는 피로에 의해서 발생한다. 따라서 지금까지 모드 혼합비가 피로 특성에 어떤 영향을 미치는지에 대한 수많은 연구가 수행되어 오고 있다. 하지만 대부분의 연구가 금속/금속 계면이나 복합재료 층간 분리에 관한 연구이다. 따라서 본 연구에서는 이종재료인 복합재료/금속 계면의 피로 특성에 대한 기초 자료를 얻고자 하였다. 이를 위하여 복합재료와 탄소강을 동시 경화법을 이용하여 접합한 SLB(single leg bending) 시편을 이용하여 피로 실험을 수행하였다. 특히, 피로 특성에 모드 혼합비$(G_{II}/G_T)$가 어떠한 영향을 미치는지에 대해 알아보고자 하였다. 전체적으로 모드 II 하중 성분 이 많을수록 균열진전속도가 빨라진다는 결과를 얻었다.

• Structural Engineering and Mechanics
• /
• 제48권1호
• /
• pp.41-56
• /
• 2013

Initiation and growth of delamination is a great concern of designers of composite structures. Interface elements with de-cohesive constitutive law in the content of continuum damage mechanics can be used to predict initiation and growth of delamination in single and mixed mode conditions. In this paper, an interface element based on the cohesive zone method has been developed to simulate delaminatoin growth of post-buckled laminate under fatigue loading. The model was programmed as the user element and user material by the "User Programmable Features" in ANSYS finite element software. The interface element is a three-dimensional 20 node brick with small thickness. Because of mixed-mode condition of stress field at the delamination-front of post-buckled laminates, a mixed-mode bilinear constitutive law has been used as user material in this model. The constitutive law of interface element has been verified by modelling of a single element. A composite laminate with initial delamination under quasi-static compressive Loading available from literature has been remodeled with the present approach. Moreover, it will be shown that, the closer the delamination to the free surface of laminate, the slower the delamination growth under compressive fatigue loading. The effects of laminate configuration on delamination growth are also investigated.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.993-1000
• /
• 2002

The objective of this work is to develop the capability to analyze accurately the mixed-mode propagation of a crack in composite structures with elastic orthotropic material stiffness properties and anisotropic material strength characteristics. In order to develop the capability to fully analyze fracture growth and failure in anisotropic structures, we examined the fundamental problem of mixed mode fracture by carrying out the analysis on orthotropic materials with an inclined crack subject to biaxial loading. Our goal here is to include an additional term in the asymptotic expansion of the crack tip stress field and to show that the direction of crack initiation can be significantly affected by that term. We employ the normal stress ratio theory to predict the direction of crack extension. It is shown that the angle of crack extension can be altered by horizontal loads and the use of second order term in the series expansion is important f3r the accurate determination of crack growth direction.

• 대한전자공학회논문지SD
• /
• 제48권1호
• /
• pp.7-13
• /
• 2011

60GHz 대역 wireless personal area network(WPAN)을 위한 QPSK 복조기를 보인다. Mixed-mode QPSK 복조방식을 이용하여 전력소모와 면적을 줄였다. 설계된 회로는 60nm CMOS Logic 공정을 통해 제작되었으며, 4.8GHz 캐리어에서 최대 4.8Gb/s의 QPSK신호를 복조할 수 있다. 이 주파수에서, 복조기는 1.2V전원에서 54 mW를 소모하며, $150{\times}150{\mu}m^2$의 면적을 차지한다. 제작된 칩을 이용하여, 60GHz 링크에서 1.7GSymbol/s QPSK신호의 송선 및 복조 실험결과를 보인다.

• 한국정보통신학회논문지
• /
• 제16권2호
• /
• pp.319-324
• /
• 2012

본 논문에서는 개선된 charge pump 회로를 이용하여 구성한 2-dimensional 터치스크린 패널 드라이버를 소개한다. 개선된 전정 센싱 회로는 charge pump 회로의 중간노드 전하 축적을 제거하여 출력 전압 표류 현상을 효과적으로 없앤다. 터치 패널 드라이버는 터치를 감지하는 아날로그 센싱 부분과 감지된 신호를 처리하는 디지털 신호 처리 부분으로 이루어진다. 제안된 터치스크린 드라이버의 동작을 확인하기 위하여 혼성 모드로 회로를 구성하고 Cadence Spectre를 이용하여 그 동작을 검증하였다. 디지털 회로 부분은 Verilog-A로 모델링하여 아날로그 회로와 인터페이스가 가능하게 하여 전체 회로 동작을 검증함으로써 혼성모드 회로 동작의 신뢰성을 확보하였고 시뮬레이션 시간을 단축할 수 있었다. 시뮬레이션 결과 개선된 전정 센싱 회로를 이용한 제안된 구조의 터치 패널 드라이버의 안정적인 동작을 확인하였다.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3498-3506
• /
• 1996

A loading device to be used in fracture experiment is presented. It's loading angle can be adjusted from $-45^{\circ}$ to $105^{\circ}$ at intervals of $15^{\circ}$ for a CTS ( compact tension-shear) specimen, so that it is to be useful to measure mixed mode toughness. The equations to give the $K_ I$, $K_ I1$ and J-integral for the experiment are evluated though finite elemetn analysis in which the loading procedure is simulated and the behaviors of the specimen such as load-displacement curve are estimated. In the course of the evaluation the values $K_ I$, $K_ I1$ and J-integral calculated through recentrly released numerical methods are employed as the reference ones.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.37-38
• /
• 2009

SiC power device possesses attractive features, such as high breakdown voltage, high-speed switching capability, and high temperature operation. In general, device design has a significant effect on the switching characteristics. It is known that in SiC power MOSFET, the JFET region width is one of the most important parameters. In this paper, we demonstrated that the switching performance of DMOSFET is dependent on the with width of the JFET region by using 2-D Mixed-mode simulations. The 4H-SiC DMOSFETs with a JFET region designed to block 800 V were optimized for minimum loss by adjusting the parameters of the n JFET region, CSL, and n-drift layer. It has been found that the JFET region reduces specific on-resistance and therefore the switching characteristics depend on the JFET region.

• Structural Engineering and Mechanics
• /
• 제75권5호
• /
• pp.559-569
• /
• 2020

In the present study, the fracture toughness of U-shaped notches made of aluminum alloy Al7075-T6 under combined tension/out-of-plane shear loading conditions (mixed mode I/III) is studied by theoretical and experimental methods. In the experimental part, U-notched test samples are loaded using a previously developed fixture under mixed mode I/III loading and their load-carrying capacity (LCC) is measured. Then, due to the presence of considerable plasticity in the notch vicinity at crack initiation instance, using the Equivalent Material Concept (EMC) and with the help of the point stress (PS) and mean stress (MS) brittle failure criteria, the LCC of the tested samples is predicted theoretically. The EMC equates a ductile material with a virtual brittle material in order to avoid performing elastic-plastic analysis. Because of the very good match between the EMC-PS and EMC-MS combined criteria with the experimental results, the use of the combination of the criteria with EMC is recommended for designing U-notched aluminum plates in engineering structures. Meanwhile, because of nearly the same accuracy of the two criteria and the simplicity of the PS criterion relations, the use of EMC-PS failure model in design of notched Al7075-T6 components is superior to the EMC-MS criterion.