• IEMEK Journal of Embedded Systems and Applications
• /
• v.10 no.6
• /
• pp.381-390
• /
• 2015

The efficient design of a transport protocol contributes to energy conservation as well as performance improvement in wireless sensor networks (WSNs). In this paper, a node-density-aware transport protocol (NDTP) for intra-cluster transmissions in WSNs for monitoring physical attributes is proposed, which takes node density into account to mitigate congestion in intra-cluster transmissions. In the proposed NDTP, the maximum active time and queue length of cluster heads are restricted to reduce energy consumption. This is mainly because cluster heads do more works and consume more energy than normal sensor nodes. According to the performance evaluation results, the proposed NDTP outperforms the conventional protocol remarkably in terms of network lifetime, congestion frequency, and packet error rate.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.882-885
• /
• 2018

Recently, signal integrity on PCB (printed circuit board) becomes very important as the system operation speed increases. So far, PCB is customarily designed to minimize area and cost. However, ultra-high-speed PCB often fail to operate properly, unless it is precisely and carefully designed considering dielectric characteristics, line width, line spacing, and impedance matching. This paper surveys many problems in ultra-high-speed PCB and various design methods to mitigate them.

• Journal of the Korean housing association
• /
• v.14 no.5
• /
• pp.65-74
• /
• 2003

Recently, the environmental conservation has been emphasized over the world. Building industry should carefully reflected the development focused on the economic aspect as well as the environmental considerations. Therefore, it requires the technology development to mitigate the environmental pollution through the reducement of the energy and resources usage amount over the building life cycle. For these, it should be required to set up the analysis methodology to grasp the amount of the environmental pollution and energy and resources in each step of building life cycle. In this paper, it aimed at preparing the analysis process and analyzing the embodied energy and $CO_2$ and $SO_x$ emission according to the building work, field work, mechanical and electrical work on the new building and remodelling, utilizing the inventory analysis which is one of the LCA process.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.1
• /
• pp.13-18
• /
• 2011

More and all-electric aircraft (AEA) carry many loads with varied functions. In particular, there may be large pulsed loads with short duty ratios which can affect the normal operation of other loads. In this paper, a converter with spilt capacitors and an improved adaptive controller is used as the Voltage Bus Conditioner (VBC) with the reduced capacitive storage to mitigate the voltage transients on the bus. The proposed converter allows the smaller capacitive storage. Also, the proposed controller has the advantage of requiring only one sensor and performing both the functions of mitigating the voltage bus transients and maintaining the level of energy stored. Experimental results are presented which verify the control principles and demonstrate the practicality of the approach.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.44-45
• /
• 2008

The zone 3 elements of distance relays play an important role during the propagation of cascaded events. The most challenging problem to mitigate catastrophic failures is to distinguish between actual faults with line flow transfer from other disconnected lines. This paper presents an adaptive protective relaying scheme based on Line Outage Distribution Factor(LODF) and Generation Shift Factor(GSF) to prevent zone 3 tripping during the cascaded events. Internet based secure peer to peer communication is recommended as a communication method of proposed scheme. Several communication issues such as reliability, speed and cyber security are discussed. In order to establish the feasibility of the proposed scheme, computer simulations for a six bus system has been performed.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.155-156
• /
• 2015

Recently, electricity consumption has rapidly increased along with economic growth. The operating strategy using emergency generator is aimed, to resolve a demand response management. For strategy of peak shedding using emergency generator, it is essential to introduce the fast transfer switching device. One of the most effective solutions is to use a static transfer switch (STS) based on thyristor. However, the characteristic of natural commutated SCR thyristor should anticipate short duration voltage sag. STS system thus requires more than a quarter cycle to successfully complete transfer process. This paper proposes the operation scheme of the STS system using the forced-commutation technique to mitigate instantaneous voltage sag during peak transfer process. Proposed STS system improved turn-off characteristic thus accomplishes the peak load shedding satisfied power quality. Performance of the proposed STS system is evaluated using electromagnetic transient program (EMTP) to confirm the effectiveness.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.177-178
• /
• 2015

This paper proposes a power smoothing scheme of a doubly-fed induction generator. The proposed scheme aims to mitigate system frequency deviation caused by the variable wind. To achieve this, a dynamic droop loop is used and its gain changes with rate of change of frequency so that it can release a large amount of kinetic energy at the initial stage of a frequency event. The performance of the proposed scheme was investigated in a model system with high wind penetration using EMTP-RV simulator. The test results indicate that the scheme can smooth the output power by absorbing or releasing the output power under a varying wind condition.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.85-93
• /
• 2015

Construction sites have various risks, and safety managements are enforced based on the law such as Industrial Safety and Health Act, etc. Safety management by the law saves lives and preserves health of workers by removing and understanding risks in advance. When the emergency situation has come, poor response causes loss of lives and physical damages. This study suggests basic strategy that can mitigate the industrial disaster in all construction sites. A survey was conducted to identify the current safety consciousness and to evaluate first aid ability of coworkers. Finally, four measures were suggested: (1) designating muster points; (2) hiring occupational health managers; (3) increasing the first aid ability of coworkers; and (4) carrying safety brochure. The proposed suggestions can be helpful in mitigating the construction disaster, and in responding the major accident efficiently within a short time.

• Smart Structures and Systems
• /
• v.19 no.4
• /
• pp.351-360
• /
• 2017

Protection of structures against natural hazards such as earthquakes has always been a major concern. Semi-active control combines the reliability of passive control and versatility and adaptability of active control. So it has recently become a preferred control method. This paper proposes an algorithm based on Uniform Deformation Theory to mitigate vulnerable buildings using magneto-rheological (MR) damper. Due to the successful performance of fuzzy logic in control of systems and its simplicity and intrinsically robustness, it is used here to regulate MR dampers. The particle swarm optimization (PSO) algorithm is also used as an adaptive method to develop a fuzzy control algorithm that is able to create uniform inter-story drifts. Results show that the proposed algorithm exhibited a desirable performance in reducing both linear and nonlinear seismic responses of structures. Performance of the presented method is indicated in compare with passive-on and passive-off control algorithms.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1679-1682
• /
• 2008

Pulsatile Extracorporeal Membrane Oxygenation(ECMO) can mitigate the heart load and raise the patient's blood perfusion. But If the ECMO pulsate the blood flow during the systolic period, It can burden to the patient's heart. To avoid the heart injury, we have to consider the relation between output of ECMO, hemodynamic states and heart movement. To raise the efficacy of the pulsatile ECMO, we investigated the coronary perfusion, cardiac muscle tension and hemodynamic states during the ECMO perfusion by using the mathematical model of human blood circulatory system and ECMO. The outflow data of the pulsatile ECMO(T-PLS, Bioheartkorea, Korea) was obtained in vitro experiments. According to the phase and pumping rate of the ECMO, the heart's load and coronary perfusion could be adjusted to the proper levels. The results of the human- ECMO lumped parameter model showed that the synchronizing operation of the pulsatile ECLS can be helpful at stabilizing the patient's hemodynamic states.