• Journal of the Korean Operations Research and Management Science Society
• /
• v.35 no.2
• /
• pp.53-69
• /
• 2010

This paper proposes an ant-based routing algorithm, Ant System-Routing in wireless Senor Networks(AS-RSN), for wireless sensor networks. Using a transition rule in Ant System, sensors can spread data traffic over the whole network to achieve energy balance, and consequently, maximize the lifetime of sensor networks. The transition rule advances one of the original Ant System by re-defining link cost which is a metric devised to consider energy-sufficiency as well as energy-efficiency. This metric gives rise to the design of the AS-RSN algorithm devised to balance the data traffic of sensor networks in a decentralized manner and consequently prolong the lifetime of the networks. Therefore, AS-RSN is scalable in the number of sensors and also robust to the variations in the dynamics of event generation. We demonstrate the effectiveness of the proposed algorithm by comparing three existing routing algorithms: Direct Communication Approach, Minimum Transmission Energy, and Self-Organized Routing and find that energy balance should be considered to extend lifetime of sensor network and increase robustness of sensor network for diverse event generation patterns.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.4
• /
• pp.251-257
• /
• 2022

We formulated the convex optimization based minimum energy soft landing problem for reusable launch vehicles, and obtained the minimum time trajectory via the bisection search. In order to implement the the optimal guidance command and complete the flight control architectures on the soft landing stage, we designed the classical attitude control loops, and formulated and solved the optimal actuator allocation problem. The obtained soft landing guidance performance was analyzed via nonlinear 6-DOF simulation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.53-60
• /
• 2011

In Wireless Sensor Networks, IEEE 802.11 happen unnecessary energy consume because of packet transmission using maximum power between sensor node. The BASIC scheme is to use maximum transmission power for RTS-CTS and minimum required transmission power so as to high energy efficiency for DATA-ACK. However BASIC scheme may degrade network throughput with collision of ACK packet by node in carrier sensing zone and may result in higher energy consumption than when using IEEE 802.11 without power control. Existing PCM(Power Control MAC) scheme is to use DATA packet transmission method by periodically maximum power level so as to sensing DATA packet transmit in carrier sensing zone of transmission node, and this method can avoid collision of ACK packet. This paper present problem by energy efficiency of PCM scheme, and design some more improved PCM scheme.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1030-1036
• /
• 1998

When the lateral dimensions of a duct is larger than or comparable to the wavelengths of Interest, higher order modes propagate in the duct. These modes will be radiated and produce noise. A number of sensors and actuators for control of radiating noise from the duct have to be incorporated with the number of modes which one wants to control. These considerations motivated the present study that considers a control system which has less microphones and control sources than required. In this work, by theoretical analysis, the control performance of such a kind of system is investigated in terms of sound-field variables and control system variables. The possible maximum and minimum value. mean and variance of residual acoustic potential energy are derived for the set of primary sound fields.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.1
• /
• pp.1-13
• /
• 1997

This paper reports the dynamic analysis of energy consumption for an office building by heat resistance-capacitance method. If a building is divided into several wall components and the wall components is replaced by one thermal capacitance and several thermal resistances, the building becomes an electric circuit. By solving the simultaneous equations of the circuit, the dynamic heat transfer characteristics and the energy consumption rate of the building were predicted. Accuracy of modified BIN method was evaluated by the present resistance-capacitance method. The result shows that modified BIN method overpredicts the heating load of the office building 15%. Annual energy consumptions of equipments(fan, boiler, chiller) for various ventilating control system(CAV, VAV, FCU+VAV, FCU+CAV) were compared. FCU+CAV shows the minimum annual energy consumption.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1079-1088
• /
• 2018

A line overload emergency control strategy based on the source-load synergy coefficient is proposed in this paper. First, the definition of the source-load synergy coefficient is introduced. When line overload is detected, the source-load branch synergy coefficient and source-load distribution synergy coefficient are calculated according to the real-time operation mode of the system. Second, the generator tripping and load shedding control node set is determined according to the source-load branch synergy coefficient. And then, according to the line overload condition, the control quantity of each control node is determined using the Double Fitness Particle Swarm Optimization (DFPSO), with minimum system economic loss as the objective function. Thus load shedding for the overloaded line could be realized. On this basis, in order to guarantee continuous and reliable power supply, on the condition that no new line overload is caused, some of the untripped generators are selected according to the source-load distribution synergy coefficient to increase power output. Thus power supply could be restored to some of the shedded loads, and the economic loss caused by emergency control could be minimized. Simulation tests on the IEEE 10-machine 39-bus system verify the effectiveness and feasibility of the proposed strategy.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.565-569
• /
• 1993

In this paper, a specified number of actuators are selected from a given set of admissible actuators. The selected set of actuators is likely to use minimum control energy while required output variance constraints are guaranteed to be satisfied. The actuator selection procedure is an iterative algorithm composed of two parts; an output variance constrained control and an input variance constrained control algorithm. The idea behind this algorithm is that the solution to the first control problem provides the necessary weighting matrix in the objective function of the second optimization problem, and the sensitivity information from the second problem is utilized to delete one actuator. For variance constrained control problems, by considering a dual version of each control problem an efficient algorithm is provided, whose convergence properties turn out to be better than an existing algorithm. Numerical examples with a simple beam are given for both the input/output variance constrained control problem and the actuator selection problem.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.236-240
• /
• 2011

Currently one of the most importance issues in industrial sector is energy cost and energy efficiency. The manufacturing plants especially have made many efforts to reduce energy cost by implementing maintenances. But in many cases, they are not aware that how much energy could be saved more. If we know the best energy consumption, which signifies energy baseline, we can control the intensity of maintenances. One way to obtain the baseline is using proper statistics from a specific plant, a sector of industry. Energy bandwidth signifies the gap between actual Specific Energy Consumption(SEC) of a certain plant and minimum SEC of the best plant, and estimate energy saving potential(ESP) is a result of bandwidth analysis. We chose a model plant and implemented some maintenance for a year, and then we obtained ESP. Additionally we could determine the decreased amount of carbon emissions from the plant using Carbon Emissions Factor(CEF) by Intergovernmental Panel on Climate Change(IPCC).

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.448-457
• /
• 1998

A neural network based control algorithm with fuzzy compensation is proposed for the automated adjustment in the production of electronic end-products. The process of adjustment is to tune the variable devices in order to examine the specified performances of the products ready prior to packing. Camcorder is considered as a target product. The required test and adjustment system is developed. The adjustment system consists of a NNC(neural network controller), a sub-NNC, and an auxiliary algorithm utilizing the fuzzy logic. The neural network is trained by means of errors between the outputs of the real system and the network, as well as on the errors between the changing rate of the outputs. Control algorithm is derived to speed up the learning dynamics and to avoid the local minima at higher energy level, and is able to converge to the global minimum at lower energy level. Many unexpected problems in the application of the real system are resolved by the auxiliary algorithms. As the adjustments of multiple items are related to each other, but the significant effect of performance by any specific item is not observed. The experimental result shows that the proposed method performs very effectively and are advantageous in simple architecture, extracting easily the training data without expertise, adapting to the unstable system that the input-output properties of each products are slightly different, with a wide application to other similar adjustment processes.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.8
• /
• pp.763-770
• /
• 2000

In tunnel ventilation, the Purpose of ventilation control is to keep the required pollution level with minimum consumption of energy But tunnel ventilation has large disturbances caused by discharge of pollutants, traffic forces especially strong for longitudinal ventilation. Hence in this paper, the tunnel ventilation control logic applying fuzzy control theories is proposed and the simulation program of tunnel ventilation control is developed. The characteristics of longitudinal ventilation with jet fans are estimated and the effect of the proposed tunnel ventilation control is verified by the simulation program.