• Journal of Welding and Joining
• /
• v.33 no.1
• /
• pp.61-71
• /
• 2015

The effect of welding condition on microstructure and mechanical property of Plasma-MIG Hybrid Weld between Al 5083 plates(thickness : 10mm) was investigated. 1 pass weld without any defects such as puckering, undercut, and lack of fusion was obtained by 150~200A of plasma current and 5~7mm of welding speed. Gas porosities and shrinkage porosities were existed in the weld near fusion line. As welding speed and plasma current were decreasing, the area fraction of porosity was increasing. The hardness of the weld is increasing as welding speed. On the basis of microstructural analysis, Mg segregated region near dendrite boundaries tends to increase with the welding speed. In the result of hardness test, Distribution of hardness in fusion zone showed little change with the plasma current. However, when the welding speed increased, hardness in weld metal markdly increased. It could be considered that effect of heat input to growth of the dendritic solidification structures. Based on tensile test, tensile properties of weld metal was predominated by area fraction of porosities. Consequently, tensile properties can be controlled by formation site and area fraction of porosity.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.581-586
• /
• 2003

3%C-18%Cr-1%Mo-2%Ni-1%Mn high chromium cast iron was casted and destabilized at temperatures of 900, 1000 and $1100^{\circ}C$ for 1, 2, 4 and 8hr under $N_2$atmosphere to observe the effect of destabilization temperature and time on the carbide and matrix structures. In as-cast condition, the microstructure consisted of $M_{ 7}$$C_3$ carbides and matrix structures which were composed of 91.50% austenite and 8.50% martensite. Numerous fine secondary carbides were observed in the specimens destabilized at $900^{\circ}C$ for 1, 2, 4 and 8hr. But, the number of secondary carbides were much reduced with the increased destabilization temperature. More austenite was formed in the matrix with the higher destabilization temperature. The amounts of austenite in the matrix were 4.23% at $900^{\circ}C$, 29.68% at $1000^{\circ}C$ and 66.51% at$ 1100^{\circ}C$, respectively. However, the effect of destabilization time on the secondary carbide and matrix was very weak compared with that of destabilization temperature. The ranges of the amount of austenite in the matrix from 1hr to 8hr destabilization heat treatment were: 3.95%-4.35% at $900^{\circ}C$, 28.89%-30.15% at $1000^{\circ}C$ and 65.13%-67.12% at $1100^{\circ}C$, respectively. The variation ranges were very narrow. The equilibrium concentration of C and Cr in austenite was already reached within 1hr during destabilization heat treatment. After an attainment of the equilibrium concentration of C and Cr in austenite, no more secondary carbide was precipitated from the matrix.

• Journal of Surface Science and Engineering
• /
• v.47 no.3
• /
• pp.128-136
• /
• 2014

In the present study, we successfully developed an eco-friendly chemical etching solution and proper condition for plating on ABS material. The mechanism of forming Ni plating layer on ABS substrate is known as following. In general, the etching solution used for the etching process is a solution of chromic acid and sulfuric acid. The etching solution is given to the surface resulting in elution of butadiene group, so-called anchor effect. Such a rough surface can easily adsorb catalyst resulting in the increase of adhesion between ABS substrate and Ni plating layer. However a use of chromic acid is harmful to environment. It is, therefore, essential to develop a new alternative solution. In the present study, we proposed an eco-friendly etching solution composed of potassium permanganate, sulfuric acid and phosphoric acid. This solution was testified to observe the surface microstructure and the pore size of electrical Ni plating layer, and the adhesive correlation between deposited layers fabricated by electro Ni plating was confirmed. The result of the present study, the newly developed, eco-friendly etching solution, which is a mixture of potassium permanganate 25 g/L, sulfuric acid 650ml/L and phosphoric acid 250ml/L, has a similar etching effect and adhesion property, compared with the commercially used chromium acid solution in the condition at $70^{\circ}C$ for 5 min.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.852-856
• /
• 2015

In this study, we investigate the effect of high-energy ball milling on thermoelectric transport properties in double-filled $CoSb_3$ skutterudite ($In_{0.2}Yb_{0.1}Co_4Sb_{12}$). $In_{0.2}Yb_{0.1}Co_4Sb_{12}$ powders are milled using high-energy ball milling for different periods of time (0, 5, 10, and 20 min), and the milled powders are consolidated into bulk samples by spark plasma sintering. Microstructure analysis shows that the high-energy ball milled bulk samples are composed of nano- and micro-grains. Because the filling fractions are reduced in the bulk samples due to the kinetic energy of the high-energy ball milling, the carrier concentration of the bulk samples decreases with the ball milling time. Furthermore, the mobility of the bulk samples also decreases with the ball milling time due to enhanced grain boundary scattering of electrons. Reduction of electrical conductivity by ball milling has a decisive effect on thermoelectric transport in the bulk samples, power factor decreases with the ball milling time.

• Computers and Concrete
• /
• v.2 no.1
• /
• pp.79-96
• /
• 2005

The use of high-strength concrete (HSC) has significantly increased over the last decade, especially in offshore structures, long-span bridges, and tall buildings. The behavior of such concrete is noticeably different from that of normal-strength concrete (NSC) due to its different microstructure and mode of failure. In particular, the shear capacity of structural members made of HSC is a concern and must be carefully evaluated. The shear fracture surface in HSC members is usually trans-granular (propagates across coarse aggregates) and is therefore smoother than that in NSC members, which reduces the effect of shear transfer mechanisms through aggregate interlock across cracks, thus reducing the ultimate shear strength. Current code provisions for shear design are mainly based on experimental results obtained on NSC members having compressive strength of up to 50MPa. The validity of such methods to calculate the shear strength of HSC members is still questionable. In this study, a new approach based on artificial neural networks (ANNs) was used to predict the shear capacity of NSC and HSC beams without shear reinforcement. Shear capacities predicted by the ANN model were compared to those of five other methods commonly used in shear investigations: the ACI method, the CSA simplified method, Response 2000, Eurocode-2, and Zsutty's method. A sensitivity analysis was conducted to evaluate the ability of ANNs to capture the effect of main shear design parameters (concrete compressive strength, amount of longitudinal reinforcement, beam size, and shear span to depth ratio) on the shear capacity of reinforced NSC and HSC beams. It was found that the ANN model outperformed all other considered methods, providing more accurate results of shear capacity, and better capturing the effect of basic shear design parameters. Therefore, it offers an efficient alternative to evaluate the shear capacity of NSC and HSC members without stirrups.

• Journal of the Korean Ceramic Society
• /
• v.20 no.2
• /
• pp.99-106
• /
• 1983

This experiment has been carried out for the purpose of investigating the effect of $Ga_2O_3$ and $GeO_2$ additivies on sintering of magnesium oxide over the temperature range of 130$0^{\circ}C$~150$0^{\circ}C$. The effect of calcining temperature on the bulk densities of fired compacts prepared from this material was observed MgO powder has been obtained by calcining extra reagent grade magnesium carbonate(basic fired) at 90$0^{\circ}C$ for 30 minutes $Ga_2O_3$and GeO2 were added in the ratio of 1, 2, and 3 wt% to MgO and mixed with calcined MgO. The specimens were prepared by compression with pressure of $700kg/cm^2$ than fired at 130$0^{\circ}C$~150$0^{\circ}C$ for 0-5hrs. Sintering behaviour and microstructure of the fired specimens were examined. The optimum calcination temperature of magnesium carbonate was 90$0^{\circ}C$. Densification rates obeyed the equation D=K in t+c. Theoretical density in the case of addition of $Ga_2O_3$ was 23.1 kcal/mole in the case of the additive $GeO_2$ was 14.176kcal/mole. This low value would appear to support a machanism of grain boundatry diffusion The range of average grain size in the case of addition of $Ga_2O_3$ and $GeO_2$ was 21$\mu\textrm{m}$-31$\mu\textrm{m}$.

• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.77-85
• /
• 1987

Hardened cement paste is mainly affected by corrosion of sulphate and chlorine ions in sea water. In this investigation, many specimens were made with the cement clinker minerals such as C3S, C3A, C4AF and their mixture according to cement composition added various blending materials. After the specimens were immersed in 4% MgSO4 and MgCl2 solutions, the product of reaction, the microstructure of specimen and Ca+2 ion leached in the solution were studied. The formation of Ca(OH)2 in the specimen of C3S is reduced relatively by adding pozzolanic admixtures. The chlorine ion is easily diffuse into the C3S specimen and produced CaCl2 compound, and it makes the specimen porous by leaching out itself into the solution. The specimen of C3A, C4AF are broken down by expanding reaction of ettringite and gypsum compound produced in the MgSO4 solution. At a later period, the ettringite is transformed into gypsum and 5MgO.2Al2O3·15H2O. The C3A in the MgCl2 solution combines chlorine ion to form Friedel's salt and prevents the diffusion reaction of chlorine ion into the specimen. Granulated slag shows inferior effect on the resistance of the specimen in MgSO4 solution by forming ettringite and gypsum, but good result in MgCl2 solution. Pozzolanic materials, on the whole, offer noticable effect on the resistance of the specimen in both solutions.

• Journal of the Korean Ceramic Society
• /
• v.26 no.3
• /
• pp.438-444
• /
• 1989

The role of TiC and the effect of Y2O3 addition on the densification, microstructure and mechanical properties of Al2O3-TiC composite have been studied. The amount of Y2O3 has been varied from 0 to 2 wt.% while keeping the TiC content at 10, 20 or 30 wt.%. The powder compacts have been sintered at 1,75$0^{\circ}C$ for various times in 1 atm Ar atmosphere and hot isostatically pressed (HIPed) at 1,$600^{\circ}C$ for 0.5h under 1,500atm Ar. Considerable increase in sintered density(over 95%) has been achieved by adding 0.5 wt.% Y2O3 in specimens containing high TiC volume. More addition of Y2O3 does not affect the densification. With increasing the sintering time from 0.5 to 4h, slight increase in density results. The growth of Al2O3 grain has been enhanced by Y2O3 addition ; this tendency is reduced with increasing TiC content because of grain boundary dragging effect of TiC particles. The hardness of specimens increases considerably by an addition of 0.5wt.% Y2O3 owing to the density increase. Further addition of Y2O3 has no effect on hardness. Fracture toughness augments with TiC content by crack deflection around the particles. By adding 0.5wt.% Y2O3, all the specimens can be densified to isolated pore stage and thus can be HIPed to full densification and better mechanical property. In particular, the fracture toughness of Al2O3-30 TiC specimen increases about 50% by HIPing. Fully dense Al2O3-30 TiC with good mechanical properties can be prepared by normal Sintering/HIPing process.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.2
• /
• pp.39-44
• /
• 2011

Plastic gradient from geometrically necessary dislocation(GND) can strongly affect micro-scale plastic behavior of polycrystalline solids. In this research, mechanical behavior of polycrystalline solid is investigated using the finite element method incorporating plastic gradient from GND effect. Gradient hardness coefficient and material length parameter are used to evaluate the effect of the plastic gradient on the behavior of materials. Sensitivity of the modeling parameters on the plastic gradient from GND is presented and effects of plastic gradient and material parameters on the behavior of single crystal inside a polycrystalline aggregate are investigated. It is confirmed that the plastic gradient from GND amplifies hardening response of polycrystals and affects single crystal behavior embedded in polycrystalline solids.

• Transactions of Materials Processing
• /
• v.30 no.5
• /
• pp.219-225
• /
• 2021

When extruding Al6061 alloys, deformation energy is deposited inside the extruded alloy depending on the deformation and the temperature of extrusion. This creates a Peripheral Coarse Grain (PCG) on the surface, where relatively more deformation energy. of the extruded alloy has been accumulated. Furthermore, since the deformation of materials continues while the materials recrystallize, it is important to examine the effect of deformation energy on dynamic recrystallization in the process of extruding Al alloys along with their microstructure. Prior studies explain the theory behind PCG growth though quantitative analysis on PCG growth of Al alloys during extrusion processes has not yet been addressed. This study aims to measure the generated PCG thickness which determines the correlation between extrusion outlet temperature and its effect on mechanical properties. Surface structure observations were performed using Optical Microscope (OM) and mechanical properties were evaluated through tensile strength and hardness measurement. Throughout this study, we endevoured to find the optimum condition of extrusion exit temperature of Al6061 and confirmed improved d reliability. This study describes the effect of the complex process variables such as exit temperature on the thickness of PCG layer for the Al6061 alloy using the 200 tons extrusion press. We therefore, discovered that the PCG layer thickness was 117 ㎛ at temperatures between 460 ℃ to 520 ℃.