• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.33-39
• /
• 1999

This study was conducted to confirm the effect of bypass dust on the hydration and mechanical properties of the cement pastes and mortar obtained from ordinary Portland cement (OPC), OPC-slag and OPC-fly ash system. The rate of heat evolution is accelerated with the content of By-pass Dust(BD). total heat evolution increased because alkali-chlorides activated the hydration of blended cement. Compressive strength and bound water content show maximum value at 5wt% By-pass Dust(BD) on each curing time in ordinary Portland cement and slag blended cement. Ca(OH)2 content of Ordinary Portland Cement increased as the content of BD and curing time. In blended cement, the formation of Ca(OH)2 is active at early hydration stage. By pozzolanic reaction, the content of Ca(OH)2 is decreased as curing time goes by. According to the BD content stable chlorides complex of Friedel's salt (C3A·CaCl2·10H2O) is created. Due to the hydration activation effect of chlorides and alkali we observed Type II C-S-H, which developed into densest microstructure.

• Journal of the Korean Ceramic Society
• /
• v.52 no.6
• /
• pp.467-472
• /
• 2015

The effect of $SrCO_3$ content on the microstructure, porosity, flexural strength, and pore size distribution of clay-based membrane supports was investigated. Green compacts prepared from low cost materials such as kaolin, bentonite, talc, sodium borate, and strontium carbonate were sintered at $1000^{\circ}C$ for 8 h in air. It was possible to control the porosity of the clay-based membrane supports within the range of 33% to 37% by adjusting the $SrCO_3$ content. The flexural strength of the clay-based membrane supports was found to strongly depend on their porosity. In turn, the porosity was affected by the $SrCO_3$ content. The average pore size and flexural strength of the clay-based membrane supports containing 4 wt% $SrCO_3$ were $0.62{\mu}m$ and 33 MPa at 34% porosity.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.83-89
• /
• 1995

In this paper, the specimens-($Ba_{0.997}$ L $a_{0.003}$)Ti $O_{3}$ + xTi $O_{2}$, x=0.005, 0.01, 0.02, 0.03[mol]- were fabricated by a solid-state reaction method which is easy in microstructure control and good in mass production. Their crystalline structures and microstructures were analysed, and electrical properties were investigated. The perovskite-crystalline structure is confirmed by XRD, and it is exhibited by SEM that the grain grows with an addition of Ti $O_{2}$. Resistivity decreases with increasing sinteiing temperature, and the specimen of ($Ba_{0.997}$ L $a_{0.003}$)Ti $O_{3}$ + 0.02Ti $O_{2}$ sintered at 1350.deg. C shows the best PTC effects. The complex impedance plots exhibit the serial equivalent circuit of ( $R_{gb}$ / $C_{gb}$ ) and $R_{g}$ it is realized that PTC effect is attributed to the resistivity of grain boundary.ary.y.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.324-331
• /
• 1995

0.36[wt%l $SiO_{2}$ and 0.1[wt%] $H_{3}$B $O_{3}$ were added to strontium ferrite magnets of the magnetoplumbite phase SrO.5.7F $e_{2}$ $O_{3}$ to hinder grain growth and accelerate sintering, respectively. This experiment was carried out to investigate effect of particle size distribution as a function of milling time(20, 30, 40, 50, 60, 70 hours) on the magnetic properties of SrO.5.7F $e_{2}$ $O_{3}$ ferrite magnet. The B-H curve, density and the degree of orientation were measured. And the microstructure of ferrite magnets was examined with a SEM. The optimal conditions and properties of the typical sample are the following : The milling time was 60 hours. Magnetic and physical properties are $B_{r}$=4, 000[G], $_{b}$ $H_{c}$=3, 330[Oe], (BH)max=3.786[MGOe], $_{I}$ $H_{c}$=3, 525[Oe], density=5.0063[g/c $m^{3}$] and orientation factor f=0.813.0.813.3.3.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.859-865
• /
• 2004

LaNiO$_3$(LNO) thin films on (100) Si substrates are prepared by sol-gel method on heat treatment conditions, such as heat transfer direction, pyrolysis and annealing process, and annealing temperatures and times. The effect of heat treatment conditions on the (100) orientations, structures and resistances of the thin films are investigated by XRD, SEM(FESEM), and a lout probe method. Highly (100) orientation factor(0.97), a pseudocubic crystalline structure with a dense and uniform microstructure could be formed by the following conditions： 1) the heat transfer direction is from Si substrate to LNO, 2) the pyrolysis and annealing process are alternated, 3) the annealing temperature is $650^{\circ}C$ and 4) the annealing times is 3 minutes. The sheet resistance of thin films decreased with increasing of a annealing temperature and time, and a number of coating.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.131-135
• /
• 2004

The effect of Co additive on the microstructural evolusion of WC was investigated. A small amount of Co powder was placed on the top-center of the pure WC powder compact and then sintered at 1950$^{\circ}C$. During sintering some abnormally large WC grains of different size and shape observed depending on the distance from the liquid source. However, in the region far away from Co liquid source, it showed low densification and the grains of WC were very small and uniform in size. A small amount of Co liquid phase has a remarkable influence on the AGG of WC and it has been explained in terms of 2-D nucleation and growth mechanism.

• Journal of the Korean Ceramic Society
• /
• v.33 no.5
• /
• pp.602-615
• /
• 1996

The purpose of the present study is to investigate the microstructural effect on the R-curve behavior in three aluminas with different grain size distributions by analyzing the bridging stress distribution. The crack opening displacement (COD) according to the distance behind the stationary crack tip was measured using an in situ SEM fracture method. The measured COD values in the fine-grained alumina agreed well with Wiederhorn's sollution while they deviated from Wiederhorn's solution in the two coarse-grained aluminas because of the increase of the crack closure due to the grain interface bridging in the crack wake. A numerical fitting procedure was conducted by the introduction of the power-law relation and the current theoretical model together with the measured COD's in order to obtain the bridging stress distribution. The results indicated that the bridging stress function and the R-curve computed by the current model were consistent with those computed by the power-law relation providing a reliable evidence for the bridging stress analysis of the current model. The strain-softening exponent in the power-law relation n, was calculated to be in the range from 2 to 3 and was closely related to the grain size distribution. Thus it was concluded from the current theoretical model that the grain size distribution affected greatly the bridging stress distribution thereby resulting in the quantitative analysis of microfracture of polycrystalline aluminas through correlating the local-fracture-cont-rolling microstructure.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.509-514
• /
• 2010

Porous mullite-bonded SiC (MBSC) ceramics were fabricated at temperatures ranging from 1400 to $1500^{\circ}C$ for 2 h using silicon carbide (SiC), alumina ($Al_2O_3$), strontium oxide (SrO), and poly (methyl methacrylate-coethylene glycol dimethacrylate) (PMMA) microbeads. The effect of template content on porosity, pore morphology, and flexural strength were investigated. The porosity increased with increasing the template content at the same sintering temperature. The flexural strength showed maximum after sintering at $1450^{\circ}C$/2 h for all specimens due to small pores and dense strut. By controlling the template content and sintering temperature, it was possible to produce porous MBSC ceramics with porosities ranging from 30% to 54%. A maximum flexural strength of ~51MPa was obtained at 30% porosity when no template were used and specimens sintered at $1450^{\circ}C$/2 h.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.334-334
• /
• 2010

In order to fabricate the multilayer piezoelectric transformer by tape casting method, we investigated the effect of $TiO_2$ and PZT powder additions on the Ag/Pd electrode. Meanwhile, effects of $TiO_2$ and PZT powder additives on the microstructure and electrical properties of Ag/Pd electrode were investigated in detail. In addition, the multilayer piezoelectric transformers were fabricated and the characteristics with various load resistance were measured at resonance frequency. The voltage step-up ratio was continuously change with increasing input voltage and load resistance, and then output voltage and powers were increased with increasing input voltage at matching impedance. The temperature rise of multilayer piezoelectric transformers were increased with increasing input voltage and load resistance. Meanwhile, multilayer piezoelectric transformers sintered at $1100^{\circ}C$ show the favorable characteristics with a power of 15 W at $100\;{\Omega}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.2
• /
• pp.126-133
• /
• 2013

This paper presents a study on the dispersion effect of the X-Ray diffraction, glass transition and DMA properties of organic modifier clay/epoxy nanocomposites produced in a homogenizer. Several experiments were conducted including different types of dispersion condition with varying processing conditions such as homogenizer rotor speed and applied time of homogenizer. The effects of these variables on the dispersion properties of nanocomposites were then studied. In order to fully understand the experimental results, a X-ray diffraction, DSC and DMA were used to investigate the effect of above mentioned variables on microstructure and intercalation/exfoliation of organic modifier clay/epoxy nanocomposites. The results from this work could be used to determine the best processing condition to obtain appropriate levels of d-spacing, glasss transition temperature and storage modulus in organic modifier clay/epoxy nanocomposites.