• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.27-36
• /
• 2006

We fabricated thermally evaporated 10 nm-Ni/(poly)Si, 10 nm-Ni/l nm-Ir/(poly)Si and 10 nm-Ni/l nm-Pt/(poly)Si films to investigate the thermal stability of nickel monosilicides at the elevated temperatures by rapid annealing them at the temperatures of $300{\sim}1200^{\circ}C$ for 40 seconds. Silicides of 50 nm-thick were formed on top of both the single crystal silicon actives and the polycrystalline silicon gates. A four-point tester was used to examine sheet resistance. A scanning electron microscope and field ion beam were employed for thickness and microstructure evolution characterization. An X-ray diffractometer and an Auger depth profiler were used for phase and composition analysis, respectively. Nickel silicides with platinum have no effect on widening the NiSi stabilization temperature region. Nickel silicides with iridium farmed on single crystal silicon showed a low resistance up to $1200^{\circ}C$ while the ones formed on polycrystalline silicon substrate showed low resistance up to $850^{\circ}C$. The grain boundary diffusion and agglomeration of silicides lowered the NiSi stable temperature with polycrystalline silicon substrates. Our result implies that our newly proposed Ir added NiSi process may widen the thermal process window for nano CMOS process.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.845-852
• /
• 2000

Mesoporous ${\gamma}-Al_2O_3$ has been prepared by selective leaching of silica from calcined domestic kaolinite. From XRD and TG-DTA data, it was found that the microstructure of a spinel phase, consisting of ${\gamma}-Al_2O_3$ containing a small mount of amorphous silica, was obtained by calcining kaolinite samples at around $1000^{\circ}C$ for 24h. Porous ${\gamma}-Al_2O_3$ was prepared by selectively dissolving the amorphous silica in KOH solutions of 1~4M at temperatures of $25~90^{\circ}C$ for leaching time of 0.5~4h. In the case of the ${\gamma}-Al_2O_3$ obtained upon KOH treatment of 4M at $90^{\circ}C$ for 1h, it showed a very narrow unimodal pore size distribution, and also formed much mesopore at a diameter of around $40~80{\AA}$. The specific surface area was $250\textrm{m}^2/g$ and the total pore volume was $0.654\textrm{cm}^3/g$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.1
• /
• pp.15-20
• /
• 2014

In this research, the geopolymer was fabricated using municipal solid waste incineration ash (denoted as MSWIA) slag and alkali activator, NaOH and its properties were analyzed. Particularly, the effects of NaOH molarity, particle size of MSWIA, and liquid/solids ratio on the compressive strength of geopolymers were investigated. The compressive strength of geopolymers fabricated increased with finer grain size of MSWIA, and optimum value of the liquid/solids ratio was identified as 0.13. As the molarity of the NaOH increased, the compressive strength of geopolymers was increased. Even more the 20 M of NaOH, but the strength was not increased. The calcium aluminum silicate and calcium aluminum silicate hydrate zeolites were generated in the geopolymer fabricated with more than 20 M of NaOH, with some unreacted silica and unknown crystals remained. The highest compressive strength, 163 MPa, of geopolymer was appeared at conditions of curing temperature $70^{\circ}C$, and 20 M of NaOH, indicating that the high concentration of NaOH accelerates the geopolymer reaction and dense microstructure. The high-strength geopolymer fabricated in the present study is expected to contribute significantly to develop the field of cement alternative substances and to improve the recycling rate of MSWIA slag.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.3
• /
• pp.130-134
• /
• 2018

In the past few years, various solder compositions have been a representative material to electronic packages and surface mount technology industries as a replacement of Pb-base solder alloy. Therefore, extensive studies on process and/or reliability related with the low Ag composition have been reported because of recent rapid rise in Ag price. In this study, Sn-3.0Ag-0.5Cu, Sn-0.7Cu and Sn-0.3Ag-0.5Cu solder bar samples were fabricated by melting of Sn, Ag and Cu metal powders. Crystal structure and element concentration were analyzed by XRD, XRF, optical microscope, FE-SEM and EDS. The fabricated solder samples were composed of ${\beta}-Sn$, ${\varepsilon}-Ag_3Sn$ and ${\eta}-Cu_6Sn_5$ phases.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.201-208
• /
• 2016

Ceramic pigments, which show good thermal and chemical stabilities, have been applied for various industry with development of digital printing technology. Ceramic inkjet printing has advantages of high efficiency of ink usage and eco-friendly process. Thus, the interest of the ceramic pigments with various function and color including CMYK (cyan, magenta, yellow, black) digital primary color is increasing. Here, we investigated the thermal and chemical stabilities of white ceramic pigment for digital inkjet printing process. The microstructure and crystal structure of MgO, $Al_2O_3$, $MgAl_2O_4$, $CeO_2$ were analyzed, and the stability with glaze were evaluated. In order to evaluate the applicability for digital inkjet printing, the chemical stability of white ceramic pigments at high temperature was investigated by characterization of the mixed color properties with CMYK ceramic pigments after firing process.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.368-374
• /
• 1998

The corrosion characteristics of zirconium alloys have been investigated in various aqueous solutions of LiOH. NaOH, KOH, RbOH. and CsOH at 3S$0^{\circ}C$. The concentrations of solutions were set to 4.3 mmol and 32.Smmol with equimolar $M^+$ and OH . The oxide characterization was performed using TEM on the samples corroded in 32. Smmol LiOH, NaOH, and KOH solution. The samples were prepared to have the same oxide thickness for the pretransition and post- transition regimes. Considering the trend of experimental data, the cation would playa major role in the corrosion process of Zr alloys in alkali hydroxide solutions. The microstructures of the oxides formed in various solutions were quite different. In LiOH solution the oxides grown in pre-transition as well as post-transition had the equiaxed structures with many pores and open grain boundaries. The oxides grown in NaOH solution had the protective columnar structures in pre-transition and the equiaxed structures with many open grain boundaries in post- transition. On the other hand. in KOH solution the columnar structure was maintained from pre- transition to post- transition. It was considered that the cation incorporation into zirconium oxide controlled the oxide characteristics and the corrosion acceleration in alkali hydroxide solutions.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.2
• /
• pp.73-77
• /
• 2021

Ga-doped ZnO thin films by RF magnetron sputtering process were synthesized according to the deposition conditions of O2 and Ar atmosphere gases, and rapid heat treatment (RTA) was performed at 600℃ in an N2 atmosphere. The thickness of the deposited ZnO : Ga thin film was measured, the crystal phase was investigated by XRD pattern analysis, and the microstructure of the thin film was observed by FE-SEM and AFM images. The intensity of the (002) plane of the X-ray diffraction pattern showed a significant difference depending on the deposition conditions of the thin films formed by O2 and Ar atmosphere gas types. In the case of a single thin f ilm doped with Ga under O2 conditions, a strong diffraction peak was observed. Under O2 and Ar conditions, in the case of a multilayer thin film with Ga doping, only a peak on the (002) plane with a somewhat weak intensity was shown. In the FE-SEM image, it was observed that the grain size of the surface of the thin film slightly increased as the thickness increased. In the case of a multilayer thin film with Ga doping under O2 and Ar atmosphere conditions, the specific resistance was 6.4 × 10-4 Ω·cm. In the case of a single thin film with Ga doping under O2 atmosphere conditions, the resistance of the thin film decreased. The resistance decreased as the thickness of the Ga-doped ZnO thin film increased to 2 ㎛, showing relatively a low specific resistance of 1.0 × 10-3 Ω·cm.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.24-31
• /
• 2021

We report structural, mechanical, and thermal properties of diecast ADC12 aluminum alloys characterized using synchrotron X-ray diffraction (XRD), scanning electron microscopy, energy dispersive X-ray (EDX) analysis, thermal conductivity (λ), Vickers hardness (Hv), and stress-strain measurements. We also studied the effect of post-annealing performed in a vacuum atmosphere on the mechanical properties of diecast ADC12 alloys. EDX and XRD results revealed that Al2Cu and AlCu3 grains are formed, well dispersed in Al base and highly crystalline. Ultimate tensile strength (UTS) of 307.9 ± 9.1 MPa and elongation of 2.98 ± 0.62 % were estimated. λ was 129.3 ± 0.27 W/m·K and Hv was approximately 130. Both values were significantly higher than the reported values. At annealing temperatures ranging from 25 to 200℃, UTS and Hv values remained constant, while as the annealing temperature increased to 500℃, these values gradually decreased. This is because stabilization of the microstructure improves toughness and ductility.

• The Journal of Advanced Prosthodontics
• /
• v.13 no.6
• /
• pp.385-395
• /
• 2021

PURPOSE. To characterize the microstructure of three yttria partially stabilized zirconia ceramics and to compare their hardness, indentation fracture resistance (IFR), biaxial flexural strength (BFS), and fatigue flexural strength. MATERIALS AND METHODS. Disc-shaped specimens were obtained from 3Y-TZP (Vita YZ HT), 4Y-PSZ (Vita YZ ST) and 5Y-PSZ (Vita YZ XT), following the ISO 6872/2015 guidelines for BFS testing (final dimensions of 12 mm in diameter, 0.7 and 1.2 ± 0.1 mm in thicknesses). Energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses were performed, and mechanical properties were assessed by Vickers hardness, IFR, quasi-static BFS and fatigue tests. RESULTS. All ceramics showed similar chemical compositions, but mainly differed in the amount of yttria, which was higher as the amount of cubic phase in the diffractogram (5Y-PSZ > 4Y-PSZ > 3Y-TZP). The 4Y- and 5Y-PSZ specimens showed surface defects under SEM, while 3Y-TZP exhibited greater grain uniformity on the surface. 5Y-PSZ and 3Y-TZP presented the highest hardness values, while 3Y-TZP was higher than 4Y- and 5Y-PSZ with regard to the IFR. The 5Y-PSZ specimen (0.7 and 1.2 mm) showed the worst mechanical performance (fatigue BFS and cycles until failure), while 3Y-TZP and 4Y-PSZ presented statistically similar values, higher than 5Y-PSZ for both thicknesses (0.7 and 1.2 mm). Moreover, 3Y-TZP showed the highest (1.2 mm group) and the lowest (0.7 mm group) degradation percentage, and 5Y-PSZ had higher strength degradation than 4Y-PSZ group. CONCLUSION. Despite the microstructural differences, 4Y-PSZ and 3Y-TZP had similar fatigue behavior regardless of thickness. 5Y-PSZ had the lowest mechanical performance.

• Computers and Concrete
• /
• v.34 no.4
• /
• pp.489-501
• /
• 2024

Geopolymers are part of a class of materials characterized by properties combining polymers, ceramics, and cement. These include exceptionally high thermal and chemical stability, excellent mechanical strength and durability in aggressive environments. This work deals with the synthesis, characterization, and sustainability evaluation of GP_GBFS-MK geopolymers by alkaline activation of a granulated blast furnace slag-metakaolin mixture. In the first step, elemental and oxide analyses by XRF and EDS showed that the main constituents of GP_GBFS-MK geopolymers are silicon, sodium, and aluminium oxides. The structural analyses by XRD and FTIR confirmed that the geopolymerization for GP_GBFS-MK geopolymers did occur, accompanied by the formation of disordered networks from the blends and a modification to the microstructure by the geopolymerization process. Similarly, the microstructural study made by SEM showed that the GP_GBFS-MK geopolymers are constituted by aluminosilicates in the form of dense clusters on which are adsorbed particles of unreacted GBFS in the form of spheroids and white residues of the alkaline activating solution. In addition, the study of the sustainability evaluation of GP_GBFS-MK geopolymers showed that the water absorption of geopolymeric materials is lower than that of OPC cement. As for the elevated temperature resistance, the analyses indicated an excellent elevated temperature resistance of GP_GBFS-MK. In the same way, the study of the resistance to chemical aggressions showed that the GP_GBFS-MK geopolymeric materials are unattackable, contrary to the OPC cement-based materials which are strongly altered.