• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.36-40
• /
• 2013

A novel design method of ultra wideband bandpass filter using CRLH transmission line with Dumbell type DGS is presented in this paper. Defected Ground Structure and microstrip interdigital capacitor are used to design the ultra wideband (UWB) filter. CRLH transmission line has composite characteristics of low pass and high pass filter. As control of cutoff frequency of low pass and high pass response on CRLH transmission line, we can get characteristic of UWB filter. We designed and simulated for CRLH transmission lines with one, two, four, and eight cells. A UWB filter using four cells CRLH is designed and fabricated to verify the results. The characteristics of designed filter have center frequency of 5GHz and relative bandwidth of 88%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.11
• /
• pp.1170-1175
• /
• 2003

In this paper, the output power improvement of Push-Push FET DRO by adding the identical DR at the drain port as one used in the gate port, has been theoretically investigated. The investigation shows that the DR located between two microstrip lines locks the phase difference of two FET's outputs at 180 degree and improves the output power of Push-Push FET DRO. Since this effect can be used for correcting the impedance difference between two FETs output circuits and the electrical length error of the power combiner at the output circuit of Push-Push DRO, which may occur when fabricate the oscillator, the oscillator with an additional DR can be useful structure for fabricating oscillator.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.159-164
• /
• 2005

Recently, it has demanded high-speed digital circuits as information increase. Therefore, electromagnetic characteristics of compact microwave circuit occurred importantly. And, the effect of the imperfect ground plane on the signal integrity and influence of coupling between two parallel lines for high-speed digital transmission line on the printed circuit board is investigated by FDTD simulations in 3-D electromagnetic analysis method. The results of FDTD simulation are compared with the ADS simulation in commercial software, analyzed lumped element of modeling and electromagnetic wave's radiation of slot as frequency. As a consequence, when the slot in the ground plane is under microstrip line, it has much effect on propagation of wave.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.8
• /
• pp.47-52
• /
• 2008

In order to enhance the rejection performance of the UWB bandpass filter based on the Composite Right- and Left-Handed Transmission-line(CRLH-TL) Metamaterial cell, we propose the lowpass filtering concept that fits into the design objectives : Keeping metamaterial property and miniaturization. So the bandpass filter itself is made far less than a quarter-wavelength and a pair of symmetric comprises lowpass filtering blocks are placed before and after the center CRLH filter which comprises tile interdigitated coupled lines and short-circuited stob. The design result will show the size of 'guided wavelength/8', the fractional bandwidth over 100%, the insertion loss much less than 1 dB, a flat Group-Delay and a good return loss performance, as expected.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.3
• /
• pp.153-157
• /
• 2008

The MCS(Micro-coplanar strip) line has been analyzed. The conformal mapping method is used to calculate the quasi-static effective permittivity and characteristic impedance of this MCS line. The computed results of the present work are found to be in good agreement when compared with the results obtained using commercial S/W, IE3D. And in this paper, the stepped-impedance low pass microstrip filter is designed and fabricated with MCS lines for improving the frequency responses. The LPF proposed structure has been also designed and implemented to have the sharp attenuation characteristics in stop band. The agreement between simulation and measurement results verify the implemented LPF.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.4
• /
• pp.825-834
• /
• 2000

In this paper, we have designed a bandpass filter with via-holes ground on K-band To pass only the 25 ~30% of the bandwidth at the center frequency of 19.6GHz, we have designed a six-order interdigital bandpass filter using microstrip lines. Simulation results of optimization according to via-holes size and numbers of interdigit bandpass filter shows a excellent agreement with theoretical values on passband frequency. Experimental results of BP filters show that mesaured center frequency is 19.150Hz, insertion loss, -4.1dB, reflection coefficient, -16.7dB. It proved that the vis-holes ground size and numbers must be considered to design the bandpass filter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.238-240
• /
• 2017

Balun using a coaxial lines i often used in microwave circuits due to easy fabrication, high operating power, and stable operation. However, it is difficult to predict an accurate balun operation characteristic due to the parasitic reactance component to be generated when the coaxial line is connected to the microstrip line existing on the substrate, and the inductance and the capacitance component of the coaxial line itself. In this paper, it is measured the phase characteristics at two output ports of the coaxial line balun which should have opposite phase characteristics. Based on these results, it will examine closely the feasibility of making more improved coaxial line balun.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.4
• /
• pp.679-687
• /
• 2017

In this paper, a microstrip-fed triple-band monopole antenna with DGS (Defected Ground Structure) for WLAN/WiMAX applications was proposed. The proposed antenna is based on a microstrip-fed structure, and composed of two strip lines and DGS structure and then designed in order to get triple band characteristics. We carried out simulation about parameters. Adjusted the position and length of the two strips and three slits, we get the optimized parameters. The proposed antenna is fabricated on an FR-4 substrate of which the dielectric constant is 4.4, and its overall size is $34mm(W_1){\times}34mm(L_1){\times}1.6mm(t)$, and its proposed antenna size is $17.0mm(W_6){\times}30.75mm(L_3+L_4+L_9)$. From the fabricated and measured results, return loss of the proposed antenna satisfied return loss -10dB bandwidth 360 MHz (2.335~2.695 GHz), 645 MHz (3.37~4.015 GHz) and 1,770 MHz (5.14~6.91 GHz). And measured results of gain and radiation patterns characteristics displayed for operating bands.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.69-74
• /
• 2010

A new package substrate for dynamic random access memory(DRAM) devices has been developed using selective aluminum anodization. Unlike the conventional substrate structure commonly made by laminating epoxy-based core and copper clad, this substrate consists of bottom aluminum, middle anodic aluminum oxide and top copper. Anodization process on the aluminum substrate provides thick aluminum oxide used as a dielectric layer in the package substrate. Placing copper traces on the anodic aluminum oxide layer, the resulting two-layer metal structure is completed in the package substrate. Selective anodization process makes it possible to construct a fully filled via structure. Also, putting vias directly in the bonding pads and the ball pads in the substrate design, via in pad structure is applied in this work. These arrangement of via in pad and two-layer metal structure make routing easier and thus provide more design flexibility. In a substrate design, all signal lines are routed based on the transmission line scheme of finite-width coplanar waveguide or microstrip with a characteristic impedance of about $50{\Omega}$ for better signal transmission. The property and performance of anodic alumina based package substrate such as layer structure, design method, fabrication process and measurement characteristics are investigated in detail.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.5
• /
• pp.413-420
• /
• 2009

We propose a novel feed network for a $2{\times}2$ array antenna to form a sectoral conical beam. The proposed feed network, which is a symmetrical structure, consists of four $90^{\circ}$ hybrids, a crossover, and four $90^{\circ}$ delay lines. To verify the performance of the feed network a $2{\times}2$ array antenna and the feed network are fabricated on a microstrip structure, and the radiation patterns are measured at the center frequency of 2.57 GHz. The maximum radiation is measured at the $45^{\circ}$ elevation angle and at the $45^{\circ}$, $135^{\circ}$, $225^{\circ}$, and $315^{\circ}$ azimuth angles depending on the choice of the input port of the feed network.