• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.97-98
• /
• 2012

This research examined the fundamental property of the MgO as the fundamental study that substituted the MgO in the low melting point modified sulfur mortar to examine the physical properties.In this research, the table floor, flexural strength test, and compressive strength test were performed. And as the replacement ratio increased, the floor showed the tendency to increase. And when being the replacement ratio 3%, the flexural strength and compressive strength made the high strength. In case of being substituted for over 5% they displayed the tendency that the intensity is degraded.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.66-71
• /
• 2000

Laser induced surface hardening of Tool steel(STC5) can be achieved either with or without surface melting. In trans-formation hardening as the surface is heated to a temperature below its melting point and is rapidly cooled solidified microstructures are usually much finer and stronger than those of the base matals. For this reason surface modification of tool steel by YAG laser irradiation has been studied as a function of processing parameters such as power density pulse width defocusing distance and molten depth. The high energy density changes and refines the microstructure of the near surface layer. In the case of beam passes martensite formed in the melt zone exhibited very high vickers hardness values. Molten depth and width depend on defocusing distance and energy of black color painting is more absorptive than other color painting.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1023-1029
• /
• 2015

Laser-assisted machining (LAM) is one of the most effective methods for enhancing the machinability of difficult-to-cut materials, such as titanium alloys and various ceramics, and has been studied by many researchers. LAM is a method that facilitates machining by softening a workpiece using a laser heat source. The advantages of the LAM process are decreases in tool wear, cutting force, and surface roughness. However, when the material is over-heated, melting or burning can occur. This study analyzed the heat source distribution with regard to overlapping of preheating on the laser heating path with an acute angle, a right angle and obtuse angles. Then, a power reduction method was proposed to reduce the melting and burning of the workpiece.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.204-209
• /
• 1995

The implementation of rapid prototyping technologies has been developed for automotive engineering by utilizing concurrent engineering principes integrated with slective laser sintering. The Selective Laser Sintering, in which a part is generated in layers form powder using a computer-controlled laser scanning apparatus and power feed system. An over view of the basic principles of SLS Machine operation is given. Binding mechanisms are described for power which becomes thermally activated bye the scanning laser beam; viscous flow and melting of a low-melting-point phase in powder. The production of parts from metal is described, including post processing to improve structural integrity and induce a transformation.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.7
• /
• pp.101-111
• /
• 1999

The effect of various conditions of frosting and defrosting on the defrosting behavior of a fin-tube heat exchanger has been examined experimentally. An electric heater is used for defrosting in a fin-tube heat exchanger. There are several local maxima in the water draining rate. The amount of residual water on the heat exchanger after completion of defrosting is kept constant due to surface tension on the heat exchanger. Without considering degradation of the thermal performance due to the frosting, the defrosting efficiency is improved with increasing amount of frost irrespective of the frosting condition. The defrosting behavior is affected by frosting density as well as frost accumulation, both of which vary with the experimental operating conditions. The heat loss to the surrounding air decreases, and melting and defrosting efficiencies show high values with decreasing heat input.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.6 no.2
• /
• pp.23-28
• /
• 2010

Fluent ver.6.3 is used as CFD(Computational Fluid Dynamics) simulator to predict the performance of snow-melting system by geothermal pipes energy. As the results of this simulation, it is clearly shown that $50^{\circ}C$ of working fluid in to geothermal evaluated as more effect comparing to $45^{\circ}C$ of working fluid. The Surface temperature is come to $5^{\circ}C$ at 1m/s speed and $50^{\circ}C$ temperature of the working fluid.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.47-50
• /
• 2006

High-speed machining is a very useful tool and one of the most effective rapid manufacturing processes. This study sought to produce various high-speed machining materials with excellent quality and dimensional accuracy. However, high-speed machining is not suitable for microscale thin-walled structures because the structure stiffness lacks the ability to resist the cutting force. This paper proposes a new method that is able to rapidly produce very thin-walled structures. This method consists of high-speed machining followed by filling. A strong work-holding force results from the solidification of the filling materials. Low-melting point metal alloys are used to minimize the thermal effects during phase changes and to hold the arbitrarily shaped thin-walled structures quickly during the high-speed machining. We demonstrate some applications, such as thin-walled cylinders and hemispherical shells, to verify the usefulness of this method and compare the analyzed dimensional accuracy of typical parts of the structures.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.37
• /
• pp.1.1-1.6
• /
• 2015

The restoration of extensive zygomatic complex defects is a surgical challenge owing to the difficulty of accurately restoring the normal anatomy, symmetry, proper facial projection and facial width. In the present study, an extensive post-traumatic zygomatic bone defect was reconstructed using a custom-made implant that was made with a selective laser melting (SLM) technique. The computer-designed implant had the proper geometry and fit perfectly into the defect without requiring any intraoperative adjustments. A one-year follow-up revealed a stable outcome with no complications.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.51-56
• /
• 2000

The Finite Element Solutions Is reported on solid-liquid phase change in porous media with natural convection including freezing. The model is based on volume averaged transport equations, while phase change is assumed to occur over a small temperature range. The FEM (Finite Element Method) algorithm used in this study is 3-step time-splitting method which requires much less execution time and computer storage the velocity-pressure integrated method and the penalty method. And the explicit Lax-Wendroff scheme is applied to nonlinear convective term in the energy equation. For natural convection including melting and solidification the numerical results show reasonable agreement with FDM (Finite Difference Method) results.

• Journal of Pharmaceutical Investigation
• /
• v.14 no.2
• /
• pp.55-61
• /
• 1984

This investigation was designed to determine the release of fenbufen from suppositories and their bioavailability in rabbits. Suppositories containing fenbufen were made by the fusion method with Witepsol H-15, Wecobee and PEG 1540 base. Displacement value, weight variation, content uniformity, melting point and melting time were determined for preformulation of the fenbufen suppositories. The release rates were determined with the KP dissolution apparatus and with cellophane tube dialysis device and were increased in order of PEG 1540, Witespol H-15 and Wecobee. The bioavailabilities of fenbufen after rectal administration were also increased in order of PEG 1540, Witespol H-15 and Wecobee.