• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.2
• /
• pp.171-181
• /
• 1988

In this study, a packet voice/data terminal(PVDT) that services both voice and data in the packet-switched network is implemented. The software structure of the PVDT is designed according to the OSI 7 layer architecture. The discrimination of voice and data is made in the link layer. Voice packets have priority over data packets in order to minimize the transmission delay, and are serviced by a simple protocol so that the overhead arising form the retransmission of packets may be minimized. The hardware structure of the PVDT is divided into five modules; a master control module, a speech proessing module, a speech activity detection module, a telephone interface module, and an input/output interface module. In addition to the hardware implementation, the optimal reconstruction delay of voice packets to reduce the influence of delay variance is analyzed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.6
• /
• pp.25-39
• /
• 2018

The purpose of this study is to develop an efficient incident detection algorithm by applying machine learning, which is being widely used in the transport sector. As a first step, network of the target site was constructed with micro-simulation model. Secondly, data has been collected under various incident scenarios produced with combination of variables that are expected to affect the incident situation. And, detection results from both McMaster algorithm, a well known incident detection algorithm, and the Naive Bayes algorithm, developed in this study, were compared. As a result of comparison, Naive Bayes algorithm showed less negative effect and better detect rate (DR) than the McMaster algorithm. However, as DR increases, so did false alarm rate (FAR). Also, while McMaster algorithm detected in four cycles, Naive Bayes algorithm determine the situation with just one cycle, which increases DR but also seems to have increased FAR. Consequently it has been identified that the Naive Bayes algorithm has a great potential in traffic incident detection.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1210-1210
• /
• 2001

On farm analysis of protein, moisture and oil in cereals and oil seeds is quickly being adopted by Australian farmers. The benefits of being able to measure protein and oil in grains and oil seeds are several : $\square$ Optimize crop payments $\square$ Monitor effects of fertilization $\square$ Blend on farm to meet market requirements $\square$ Off farm marketing - sell crop with load by load analysis However farmers are not NIR spectroscopists and the process of calibrating instruments has to the duty of the supplier. With the potential number of On Farm analyser being in the thousands, then the task of calibrating each instrument would be impossible, let alone the problems encountered with updating calibrations from season to season. As such, NIR technology Australia has developed a mechanism for \ulcorner\ulcorner\ulcorner their range of Cropscan 2000G NIR analysers so that a single calibration can be transferred from the master instrument to every slave instrument. Whole grain analysis has been developed over the last 10 years using Near Infrared Transmission through a sample of grain with a pathlength varying from 5-30mm. A continuous spectrum from 800-1100nm is the optimal wavelength coverage fro these applications and a grating based spectrophotometer has proven to provide the best means of producing this spectrum. The most important aspect of standardizing NIB instruments is to duplicate the spectral information. The task is to align spectrum from the slave instruments to the master instrument in terms of wavelength positioning and then to adjust the spectral response at each wavelength in order that the slave instruments mimic the master instrument. The Cropscan 2000G and 2000B Whole Grain Analyser use flat field spectrographs to produce a spectrum from 720-1100nm and a silicon photodiode array detector to collect the spectrum at approximately 10nm intervals. The concave holographic gratings used in the flat field spectrographs are produced by a process of photo lithography. As such each grating is an exact replica of the original. To align wavelengths in these instruments, NIR wheat sample scanned on the master and the slave instruments provides three check points in the spectrum to make a more exact alignment. Once the wavelengths are matched then many samples of wheat, approximately 10, exhibiting absorbances from 2 to 4.5 Abu, are scanned on the master and then on each slave. Using a simple linear regression technique, a slope and bias adjustment is made for each pixel of the detector. This process corrects the spectral response at each wavelength so that the slave instruments produce the same spectra as the master instrument. It is important to use as broad a range of absorbances in the samples so that a good slope and bias estimate can be calculated. These Slope and Bias (S'||'&'||'B) factors are then downloaded into the slave instruments. Calibrations developed on the master instrument can then be downloaded onto the slave instruments and perform similarly to the master instrument. The data shown in this paper illustrates the process of calculating these S'||'&'||'B factors and the transfer of calibrations for wheat, barley and sorghum between several instruments.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.2
• /
• pp.363-376
• /
• 1997

In this paper, we present a hardware architecture and a sofrware architecture for cimputer based teleconferencing systems.And also we analyse stream adtivation mechanisms for them form the viewpoint of delay. MuX that is a multimedia I/O server provides various processing elements for data I/O, synchronization, interleaving and mixing.We describe methods to build teleconferencing systems with the elements and compares the technique using master click with the techniquie using self clock.In the plase of dta input.the technique using self click is berrer than the technique using master clock.When we generate interleved stream from audio and video stream and activate channel objects by periodic audio stream as activation clock, dealy from imput audio stream to imterleved stream is reduced but delay for video stream is not reduced as much as in the case of audio stream.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.761-764
• /
• 2010

Interest in vehicle infotainment system, that provides both entertainment of driving and information for safe and convenient driving, has been recently increased. MOST is defined as the network transmitting high-bandwidth infortainment data to vehicle, and it has been standardized as MOST150. In this research, dynamic behavior method that deals with roles and functions of each devices connected to MOST150 Network, and Power Management Method was studied. MOST Network consists of a master device, including function block 'NetworkMaster', and all other devices called slave devices. The purpose of this study is to apply the analysis of the methods of operating and power management based on condition of master device and slave devices on MOST150 network to the future development of MOST150 devices.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.89-91
• /
• 2004

In SCADA systems, an RTU is a device installed at a remote location that collects data, codes the data into a format that is transmittable and transmits the data back to a central station, or MTU. An RTU also collects information from the master device and implements processes that are directed by master device. RTUs are equipped with input channels for sensing or metering, output channels for control, indication or alarms and a communications port. In general, the data are transmitted via a wired communication infrastructure such as RS422 or RS485 between RTU and MTU. But, limited range of wired communication doesn't allow the system to cover remote areas over the limitation, and building a wired communication network is not easy in the circumstances. In this Paper, we design and implement a smart cost-effective Web-RTU that can communicate with MTU via Web. Web is of benefit to the Web-RTU, because it is not only free from the distance limitations, but also is built easily and cost-effectively wherever Internet resources are available. Additionally, Web can be easily applied to the SCADA system with the development of hardware and software for communications. The Web-RTU has a program memory, a data memory and a RAM inside, and uses Atmega128, low-cost 8 bit micro-processor with eight AI(Analog Input). It performs well enough to implement all existing roles of RTU.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.203-210
• /
• 2005

Prototype model of MDU(Master Data Unit), to be employed on KSLV-I, has been developed and tested being interfaced with other units. Before stepping into the development of engineering and flight model phases, we have carried out reliability prediction of prototype MDU in order to assure availability of the unit. This paper describes the method of reliability prediction of prototype MDU and prediction results based on MIL-HDBK-217F, 'Electronic Reliability Design Handbook'.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.3
• /
• pp.91-98
• /
• 2013

Node which plays the role of cache server does not exist in the wireless ad-hoc network consisting of only mobile nodes. Even if it exists, it is difficult to provide cache services due to the movement of nodes. Therefore, the cooperative cache technique is necessary in order to improve the efficiency of information access by reducing data access time and use of bandwidth in the wireless ad-hoc network. In this paper, the whole network is divided into zones which don't overlap and master node of each zone is elected. General node of each zone has ZICT and manages cache data to cooperative cache and gateway node use NZCT to manage cache information of neighbor zone. We proposed security structure which can accomplish send and receive in the only node issued id key in the elected master node in order to prepare for cache consistent attack which is vulnerability of distributed caching techniques. The performance of the proposed method in this paper could confirm the excellent performance through comparative experiments of GCC and GC techniques.

• IE interfaces
• /
• v.22 no.1
• /
• pp.85-94
• /
• 2009

Nowadays, most of the major manufacturing companies prepare their manufacturing schedule using package based solutions. Even though the accuracy of the detail scheduling result is high at implementation, however, it is low during maintenance period. The main cause of low accuracy during maintenance period is due to difficulties in maintaining the accurate level of master data. In this paper, we propose to easily maintain setup time, which is one of the most important factors required in master data to achieve good scheduling result, after changing job. This paper is mainly focused on how to deduce the factors that influence the setup time in a roll-based manufacturing field with print operations. For this purpose, we employed rule based algorithm and applied for deciding setup time for the existing product items. Likewise, it can be applied to new items without any complex setup procedures, and, finally, it displays the result of the real setup-time and calculated setup-time.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.417-419
• /
• 2004

Because of the demands for high performance and high integrated system, the needs for optimal platform becomes more importance. Optimal platform can handle more data effectively with same resources. AMBA(Advanced Microprocessor Bus Architecture)$^{TM}$ defines on-chip communication standard for designing high performance embedded micro-controllers. It is consisted of AHB, ASB and APB. It can support fast implementation and reliability in system that is composed with reusable IPs. DMAC is one of master in system and generate master signals of AHB to communicate data from one slave(peripheral or memory) to another slave. It can reduce burden of CPU and increase system performance. We designed DMAC based on AMBA and it supports 13 Channels. Each channel can be controlled by software program. It decides channel's priority using round-robin method. It can support P2P, P2M, M2P and P2P communication.