• Preventive Nutrition and Food Science
• /
• v.8 no.4
• /
• pp.315-320
• /
• 2003

Headspace volatile compounds of oxidized fish oil were analyzed by the combination of hexane solvent or solid phase microextraction, gas chromatography and mass selective detector. The optimum condition of headspace analysis by hexane trapping was 23 min absorption time, 96$^{\circ}C$ sample temperature and 20 mL/min air flow rate. The numbers of volatile compounds identified by solvent trapping and SPME were 35 and 14, respectively. Groups having the largest amount and many kinds were hydrocarbons and aldehydes, respectively. The numbers of aldehydes were 15 and 6 for solvent trap and SPME, respectively. These basic data could be used as indicators for the quality changes of fish oil.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.792-796
• /
• 2013

A practical process to optimize engine mounts on construction equipment is presented in this research. Transmitted force from the engine is estimated by using stiffness of the mount rubber which varies with frequency, amplitude and pre-load, and by the engine excitation force that comes from piston mass and gas pressure and so on. The transmitted force is measured through TPA(Transfer Path Analysis) and is then compared with the estimated force. The optimum mount position and stiffness are solved using MATLAB. The result shows the improvement on engine mount vibration.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.6
• /
• pp.612-618
• /
• 2009

This study is concerned about the optimal design of the arm 1 and arm 2 in the SCARA robot. The mass and inertia moment of the arm I and arm 2 in a SCARA robot is greatly affected on the performance such as a cycle time, and torques loaded on $1^{st}$ axis and $2^{nd}$ axis. To reduce the mass and inertia moment, this study carried out optimal design by FEM analysis using parametric variables, which is a width, a height of the rib and a thickness of arm in the arm. The rib is adapted instead of reducing the thickness in the arm. And the simulation by computer was conducted on two given paths in X direction and Y direction. After optimal design, the result showed that maximum torque of $1^{st}$ axis and $2^{nd}$ axis reduced to maximum 9.5% on a given path.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.351-354
• /
• 2001

In this experiment, we tested various nitrogen sources and then culture condition was optimized for industrial applications. The batch culture of Candida magnoliae SR101 grown in a defined medium supplemented with light steep water (LSW) as a sole nitrogen source showed a relatively high yield of erythritol production (53%), which was slightly higher than that using yeast extract as a nitrogen source, while the productivity and cell mass were maintained at similar levels. For the optimization of culture condition, the batch culture was performed. When the concentration of LSW was 65 mL/L in the defined medium containing 250 g/L of glucose, the concentration, yield and productivity of erythritol were 110 g/L, 44%, and 0.66 g/L-hr, respectively. The high yield and comparable productivity obtained with a cheap nitrogen source could be expected as a basis for the mass production of erythritol in the industrial scale.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.09a
• /
• pp.107-110
• /
• 2001

The biological control potential of entomopathogenic nematodes (EPN) can be enhanced by improved culture efficiency. Optimization of media is a key factor for improving in vitro mass production of entomopathogenic nematodes. EPN yield was dependant of complex medium concentration, of which mixture is carbohydrates, lipids, proteins, salts, and growth factors, on the growth of Heterorhabditis bacteriophora and its symbiotic bacterium Photorhabdus luminescensLipids.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.381-386
• /
• 2000

Simple spring-damper-mass models have been widely used to understand whole-body vertical biodynamic response characteristics of the seated vehicle driver. However, most previous models have not considered about the non-rigid masses(wobbling masses). A simple mechanical model of seated human body developed in this study included the torso represented by a rigid and a wobbling mass. Within the 0.5-20Hz frequency range and for excitation amplitudes maintained below $5ms^{-2}$, this 4-degree-of-freedom driver model is proposed to satisfy the measured vertical vibration response characteristics defined from a synthesis of published data for subjects seated erect without backrest support. The parameters are identified by using the combinatorial optimization technique, simulated annealing method. The model response was found to be provided a closer agreement with the response characteristics than previously published models.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.12
• /
• pp.1168-1175
• /
• 2010

Excessive torsional vibrations from marine engine shafting systems can be reduced by using torsional vibration dampers. But in order to be tuned effectively, the dampers should be designed through the optimum design procedure. In this paper, the procedure to get the optimum values of system parameters of spring-viscous dampers using effective modal mass of inertia and stiffness is suggested and the damping is determined by the exact algebra optimization method. The validity of the suggested method is confirmed through the application to a 1800 kW four cycle diesel engine and generator system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.3
• /
• pp.512-520
• /
• 1995

This study investigates the simultanceous heat and mass transfer between a falling desiccant film and air in cross flow at the interface. The application of this work is the optimization of falling film evaporators for use in potential hybrid air conditioning systems. The specific geometry considered is liquid TEG films falling along the vertical cooled surfaces of a channel with air in cross flow. The equations to describe the coupled heat and mass transfer between a falling desiccant film and air in cross flow for a falling film evaporator have been presented and solved numerically. The effects of important design and operating variables on the evaporator performance predicted by the parametric numerical analysis and suggestions for performance improvements of the evaporator are presented.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.189-194
• /
• 2012

The purpose of this study is to predict the performance of a cyclone drying machine and air ejector used in drying applications. This paper deals with optimization of the geometry of the ejector for sludge drying using computational fluid dynamics. To facilitate the design of a jet ejector for air drying machines, a numerical model of simultaneous mass and heat transfers between the liquid(sludge) and gas(air) phases in the jet ejector was developed. The steady-state model was based on unidimensional balance equations of mass, energy and momentum for the liquid and gas phases. It was shown that the optimum condition to minimize pressure and momentum loss of air in the ejector was d=220mm. It was found that sludge particles inside the cyclone was smoothly discharged by the conical wedge installed on the bottom of the cyclone.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.109-114
• /
• 2005

The large injection molded parts technology such as instrument panel, front and rear bumper are presented for a precision molding. Some lead time and cost are required to product these part from design to mass product. Recently, CAE is widely used in product design, mold design and analysis of molding conditions to reduce time and cost. The optimal molding conditions can be obtained by DOE(Design of Experiment). The optimal design applications with CAE and DOE have been used in small molded parts. However, application to the large molded body is not reported. In this paper, optimization of injection molding process is studied for quality control in mass production of automobile bumper. Mold temperature difference is chosen through robust design of injection molding process, the molding process being optimized in term of shrinkage and deflection. The optimal conditions through DOE are validated by using injection molding analysis.