• Journal of Electrical Engineering and Technology
• /
• v.5 no.4
• /
• pp.592-596
• /
• 2010

In a multi-layer interior permanent magnet synchronous motor, the d- and q-axis parameters vary nonlinearly according to different load conditions, consequently changing the level of saturation. The flux-linkage of d- and q-axis conveys ripple characteristics resulting from mechanical structure and degree of magnetic saturation. If the calculated flux-linkage is correct, the torque using the Maxwell stress tensor method is the same torque calculated by the flux-linkage. However, discrepancy between results exists. In this paper, the d- and q-axis flux-linkage, in consideration of the ripple characteristic, is calculated. Simulation results are then compared with experimental results.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.12
• /
• pp.592-600
• /
• 2001

This Paper presents the transient analysis of the single-phase line-start permanent magnet synchronous motor. To analyse the starting characteristics, the dynamic equation which is combined electric dynamic equations with mechanical dynamic equation is used. The electric dynamics are derived from the d-q axis voltages of stator and rotor respectively. Especially, symmetrical components transformation is used to consider unbalanced magnetic field which is produced by single-phase input. Non-linear d-q axis inductances according to current amplitude and current phase angle are calculated by Finite Element Method and applied to lumped parameter circuit. The analysis methods are validated by comparing simulated and experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.257-262
• /
• 2001

Single crystalline films of La doped YIG(yttrium iron garnet) were grown by the liquid phase epitaxy. The lattice constants of films obtained by DCD(double crystalline diffractometer) measurement increased with increasing La contents in films. In particular, lattice constants of films grown wiht Y/La=20 solution were nearly same as those of GGG (gadolinium gallium garnet) substrate. The saturation magnetization measured with VSM (vibrating sample magnetometer) was about 1750Gauss which is the same as that of pure YIG irrespective of La contents in films. FMR(ferromagnetic resonance) linewidth of La doped YIG was smaller than that of pure YIG. Since appropriate La doping decreases the lattice mismatch between film and substrate, the FMR linewidth was Y/La=20 in this experiment.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.6
• /
• pp.316-321
• /
• 1999

Disk type single phase switched reluctance motor which is a simple robust construction, simple control circuit and low manufacturing cost, has a characteristics of axial and radial flux machines. However, because this DSPSRM has a complicated magnetic circuit, it is difficult to analyze the design characteristics.. In this study, the calculation of design parameter based on the conventional design theory of electric machine and the characteristics analysis by computer simulation was performed. As the DSPSRM has the characteristics of both AFM and RFM, it is difficult to analyze its characteristics by the 2D FEM. 3D FEM was applied in the analysis of energy distribution and approximated calculation of torque characteristics with rotor positions. With analysis results, prototype of DSPSRM is manufactured.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.271-276
• /
• 2006

This paper shows the rotordynamic characteristics of a turbo-generator for a BOP of a fuel cell system. The rotor-bearing system consists of magnetic shaft and compressor-turbine shaft, and the two shafts are connected by spline coupling and supported by oil free air foil bearing. Preliminary design according to several parameter is considered in detail. Static and dynamic characteristics of the AFB are estimated by the soft elasto-hydrodynamic analysis technique and the perturbation method. The results of the natural frequencies, mode shape, and unbalance response analysis are presented.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.12a
• /
• pp.44-45
• /
• 2007

We have studied the formation of alloy for $Ni_{45}AL_{45}C_{10}$ as a function of milling times. This alloy was produced using mechanical alloying. The effect of milling time on local structural changes of $Ni_{45}AL_{45}C_{10}$ has been investigated by means of EXAFS. Both XRD and EXAFS patterns from mechanically alloyed $Ni_{45}AL_{45}C_{10}$ powder indicates the formation of solid solution. The variation of lattice parameter and particle sizes could be analyzed from the different of milling times. Magnetization was also measured by using VSM.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1984.04a
• /
• pp.25-28
• /
• 1984

This paper describes the design of band-pass filter using the dielectric resonator and microstrip line depends mainly upon the magnetic field and is principal parameter as band-pass filter. Because dielectric resonator band~pass filter has a very high-Q, the bandwidth of this filter is very narrow. as a result of experiment, the dielectric resonator bandwidth of this filter is very narrow. As a result of experiment, the dielectric resonator band-pase filter has various modes central frequencies due to the mode change and good characteristric as a band-pass filter.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.3
• /
• pp.122-129
• /
• 2001

Exact simulation of conducted EMI in switched mode power supplies is proposed. In order to achieve exact simulation, PSPICE active component ABM model and modified transformer model are proposed. Each model parameter is extracted from measurements and data-books. PSPICE simulation results with high frequency PCB pattern model are accordant with EMI measurements for a 50[W] isolated flyback converter. EMI relations of each component and EMI patterns are analyzed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.1
• /
• pp.10-14
• /
• 2001

The superconducting transmission cable is one of interesting part in power application using high temperature superconducting wire. One important parameter in HTS cable design is transport current sharing because it is related with current transmission capacity and loss. In this paper, we calculate self inductances of each layer and mutual inductances between two layers from magnetic field energy, and current sharing of each layer for 4-layer cable using the electric circuit model which contain inductance and resistance (by joint and AC loss). Also, transport current losses which are calculated by monoblock model and Norris equation are compared. As a results, outer layer has always larger transport current than inner layer, and current capacity of each layer is largely influenced by resistance per unit cable length. As a conclusion, for high current uniformity and low AC loss, we have to decrease inductances themselves or those differences.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.182-184
• /
• 2001

Linear pulse Motor(LPM) are used a field where smooth linear motion is required, and it's position accuracy higher than that of a lead. According to the advantage such as simplicity of mechanical frame, high reliability, precise open_loop operation, low inertia etc LPM is applied largely where it have made motor of this kind more and more attractive in many application areas such as factory automation and high speed positioning. This paper is researched to analyze for thrust force characteristic of hybrid LPM. Both the thrust and normal force are very sensitive to the airgap and tooth pitches of the force and platen. To find the optimal design parameter on the hybrid LPM for the embroidery machine. For the field analysis, the finite element method(FEM) is employed for calculating the force. The reluctance models will be used the magnetic permeance of airgap under static-conditions. The forces between forcer and platen have been calculated using the virtual work mathod.