• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.77-86
• /
• 2009

A wavelet Electrocardiogram(ECG) detector and its analog-to-digital converter(ADC) for low-power implantable cardiac pacemakers are presented in this paper. The proposed wavelet-based ECG detector consists of a wavelet decomposer with wavelet filter banks, a QRS complex detector of hypothesis testing with wavelet-demodulated ECG signals, and a noise detector with zero-crossing points. To achieve high-detection performance with low-power consumption, the multi-scaled product algorithm and soft-threshold algorithm are efficiently exploited. To further reduce the power dissipation, a low-power ADC, which is based on a Successive Approximation Register(SAR) architecture with an on/off-time controlled comparator and passive sample and hold, is also presented. Our algorithmic and architectural level approaches are implemented and fabricated in standard $0.35{\mu}m$ CMOS technology. The testchip shows a good detection accuracy of 99.32% and very low-power consumption of $19.02{\mu}W$ with 3-V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1379-1385
• /
• 2009

We propose a low-power and high-speed client receiver for a mobile display digital interface (MDDI) newly in this paper. The low-power receiver is designed such that bias currents, sink and source currents, are insensitive to variations of power supply, process, temperature, and common-mode input voltage (VCM) and is able to operate at a rate of 450Mbps or above under the conditions of a power supply range of 3.0 to 3.6Vand a temperature range of -40 to 85$^{\circ}$C. And it is confirmed by a simulation result that the current dissipation is less than 500${\mu}$A. A test chip is manufactured with the Magna chip 0.35${\mu}$m CMOS process. When a test was done, the data receiver and data recovery circuits are functioning normally.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1776-1778
• /
• 2000

The demands placed on portable wireless communication equipment include low cost, low supply voltage, low power, dissipation, low noise, high frequency of operation, and low distortion. These design requirements cannot be met satisfactorily in many cases without the use of RF inductors. However, implementing the inductor on-chip has been regarded as an impractical task because of excessive substrate capacitance and substantial resistive losses due to metallization and the conductive silicon substrate. Hence, there is a great incentive to design, optimize, and model spiral inductors on Si substrate. So, we analyzed a chip inductors using electromagnetic analysis and established a set of design rules for rectangular spiral inductors.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.3
• /
• pp.341-346
• /
• 2017

In this paper, we present a 60 GHz on-off keying (OOK) modulator in a 90 nm CMOS. The modulator employs a current-reuse technique and a switching modulation for low DC power dissipation, high on/off isolation, and high data rate. The measured gain of the modulator, on/off isolation, and output 1-dB compression point is 9.1 dB, 24.3 dB, and 5.1 dBm, respectively, at 60 GHz. The modulator consumes power consumption of 18 mW, and is capable of handling data rates of 8 Gb/s at bit error rate of less than $10^{-6}$ for $231^{-1}$ PRBS over a distance of 10-cm with an OOK receiver module.

• Journal of Sensor Science and Technology
• /
• v.26 no.4
• /
• pp.292-296
• /
• 2017

It has become ever harder to design reliable circuits with each nanometer technology node under normal operation conditions, a transistor device can be affected by various aging effects resulting in performance degradation and eventually design failure. The reliability (aging) effect has traditionally been the area of process engineers. However, in the future, even the smallest of variations can slow down a transistor's switching speed, and an aging device may not perform adequately at a very low voltage. Because of such dilemmas, the transistor aging is emerging as a circuit designer's problem. Therefore, in this paper, the impact of aging effects on the delay and power dissipation of digital circuits by using nanomneter MOSFET power gating structure has been analyzed.. Based on this analyzed aging models, a reliable digital circuits can be designed.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.149-152
• /
• 2000

A dual-mode multiplier (DMM) that performs single- and double-precision multiplications has been designed. An algorithm for efficiently implementing double-precision multiplication with a single-precision multiplier was proposed, which is based on partitioning double-precision multiplication into four single-precision sub-multiplications and computing them with sequential accumulations. When compared with conventional double-precision multipliers, our approach reduces the hardware complexity by about one third resulting in small silicon area and low-power dissipation at the expense of increased latency and throughput cycles.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.2
• /
• pp.51-51
• /
• 2001

본 논문은 디지털 순서회로 설계시 상태할당 알고리즘 개발에 관한 연구로, 동적 소비전력을 감소시키기 위하여 상태변수의 변화를 최소로 하는 코드를 할당하여 상태코드가 변화하는 스위칭횟수를 줄이도록 하였다. 상태를 할당하는데는 Markov의 확률함수를 이용하여 hamming거리가 최소가 되도록 상태 천이도에서 각 상태를 연결하는 edge에 weight를 정의한 다음, 가중치를 이용하여 각 상태들간의 연결성을 고려하여 인접한 상태들간에는 가능한 적은 비트 천이를 가지도륵 모든 상태를 반복적으로 찾아 계산하였다. 비트 천이의 정도를 나타내기 위하여 cost 함수로 계산한 결과 순서회로의 종류에 따라 Lakshmikant의 알고리즘보다 최고 57.42%를 감소시킬 수 있었다.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.164-167
• /
• 2000

This paper introduces the design of high-speed analog-to-digital converter for hard disk drive (HDD) read channel. This is based on autozero technique for low-error rate, and Double Speed Dual ADC(DSDA) technique lot efficiently increasing the conversion speed of A/D converter. This An is designed by 6bit resolution, 800M sample/s maximum conversion rate, 390㎽ power dissipation, one clock cycle latency in 0.65 $\mu\textrm{m}$ CMOS technology.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.129-130
• /
• 2007

I/Q demodulator is designed using RC-CR quadrature divider with two balanced mixer for WLAN applications. The I/Q demodulator has low power dissipation, good I/Q mismatch, a good isolation and conversion loss. The measured results shows close agreement with the predicted performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.9
• /
• pp.789-794
• /
• 2014

The FPGA is used to the high speed digital satellite communication on the Digital Signal Process Unit of the next generation GEO communication satellite. The high capacity FPGA has the high power dissipation and it is difficult to satisfy the derating requirement of temperature. This matter is the major factor to degrade the equipment life and reliability. The thermal control at the equipment level has been worked through thermal conduction in the space environment. The FPGA of CCGA or BGA package type was mounted on printed circuit board, but the PCB has low efficient to the thermal control. For the FPGA heat dissipation, the heat sink was applied between part lid and housing of equipment and the performance of heat sink was confirmed via thermal vacuum test under the condition of space qualification level. The FPGA of high power dissipation has been difficult to apply for space application, but FPGA with heat sink could be used to space application with the derating temperature margin.