• Journal of Satellite, Information and Communications
• /
• v.9 no.4
• /
• pp.97-103
• /
• 2014

In order to verify normal operation of satellite OBC(On Board Computer), it is essential that processor monitoring and debugging. So we are using the GRMON of Aeroflex Gaisler. It provides a lot of features for debugging of LEON processor but we can't use that features on the NGSCB(Next Generation Spacecraft Computer Board) except a few things. So the cost-effectiveness is very low. And for hardware fault injection, we are using a method of modify satellite flight software, because we can't modify GRMON. This method can not guarantee normal operation of the satellite flight software. So in this paper we were developed the processor monitoring and fault injection tool for NGSCB.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.9
• /
• pp.94-102
• /
• 2008

Capacitor switching is essential for the economic operation and proper voltage control of KOREA electric utility distribution system. Voltage transients produced by capacitor switching (around 2.0 per unit at substation and 2.5 or less per unit at customer site, and lasting less then 1[ms]) do not have the magnitude or duration to interfere with the operation of computers, but they do disrupt the operation of adjustable speed drivers. The result of our research, ASD manufacturers should learn from the computer industry and design products that will operate satisfactory In the electrical envelopment in which they will be placed. In this case history, the inductors on the input to ADSs in order to prevent nuisance tripping from capacitor switching(and other causes within the apartment) proved to be an effective, low-cost solution.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.25 no.1
• /
• pp.73-81
• /
• 1997

This study was conducted to find out the hydroseeding timing of woody plants. Five native plants were used for this experiment and were seeded on the cut slopes by hands in April, May, June, September and October. In order to identify the best seeding time, germination percentage, ground cover rate and plant height were investigated. There was a difference in germination percentage and ground cover rate depending on the seeding time. The results are summerized as follows 1. Characteristics of germination : Seeding was best carried out in spring(May, June) or autumn(September). In spring, Lespedeza cyrtobotrya shows quick germination and rapid growing which can be compared with herbaceous plants using in the hydroseeding. As for Pinus thunbergii, there was little difference in germinatin according to different seeding timing. But Evodia daniellii, Parthenocis년 tricuspidata and Alnus hirsuta seem to need seed treatments to improve the seed germination. 2. Ground cover rate : The most rapid growing plant is Lespedeza cyrtobotrya and the next is Amorpha fruticosa. The other plants show extreamly low ground cover rate, so they seem to be surpressed by herbaceous plants which will be mixed for erosion control. 3. Plant height : On 8 weeks later after seeding, the Lespedeza cyrtobotrya which was seeded in June recorded 17.1cm plant height. It will be enouch height to compete with herbaceous plants. As the Parthenocissus tricuspjdata seeded in May shows 27cm plant length, it can be used more frequently on seeding works if the seed germination were improved. In sum, seeding is best carried out in May. When deciding seeding rate for the purpose of hydroseeding, it will be necessary to adjust the woody plants germination percentage according to seeding timing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.265-272
• /
• 2011

This study designed and manufactured "a DVOR virtual signal generator" to make the monitoring system of preliminary Doppler VHF Omni-directional Radio Range(DVOR) run like its real operation status in a narrow space in order to study "a DVOR virtual monitoring system". The designed and manufactured DVOR virtual signal generator is suitable for the specification of signal that is generated in the currently running equipment. In addition, it is possible to control operation conditions of equipment by using parameter variables, and the circuit construction is largely divided into the input part, the modulation part, the high-gain amplifier, and the power part. "The DVOR virtual monitoring system using the virtual signal designed and implemented in this study is very suitable to be used for low-cost actual education as it can construct the operation status like the real situation in a narrow space without using an actual system like an antenna generating side band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.11
• /
• pp.2187-2192
• /
• 2016

A data-centric routing protocol considering a data aggregation technique at relay nodes is required to increase the lifetime of wireless sensor networks. An energy-efficient data-centric routing algorithm is proposed by considering a tradeoff between acquisition time and energy consumption in the wireless sensor network. First, the proposed routing scheme decides the sink node among all sensor nodes in order to minimize the maximum distance between them. Then, the proposed routing extends its tree structure in a way to minimize the link cost between the connected nodes for reducing energy consumption while minimizing the maximum distance between sensor nodes and a sink node for rapid information gathering. Simulation results show that the proposed data-centric routing algorithm has short information acquisition time and low energy consumption; thus, it achieves high energy efficiency in the wireless sensor network compared to conventional routing algorithms.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.6
• /
• pp.262-266
• /
• 2011

A simulation study of a current-mode direct current (DC)-DC boost converter is presented in this paper. This converter, with a fully-integrated power module, is implemented by using bipolar complementary metal-oxide semiconductor (BiCMOS) technology. The current-sensing circuit has an op-amp to achieve high accuracy. With the sense metal-oxide semiconductor field-effect transistor (MOSFET) in the current sensor, the sensed inductor current with the internal ramp signal can be used for feedback control. In addition, BiCMOS technology is applied to the converter, for accurate current sensing and low power consumption. The DC-DC converter is designed with a standard 0.35 ${\mu}m$ BiCMOS process. The off-chip inductor-capacitor (LC) filter is operated with an inductance of 1 mH and a capacitance of 12.5 nF. Simulation results show the high performance of the current-sensing circuit and the validity of the BiCMOS converter. The output voltage is found to be 4.1 V with a ripple ratio of 1.5% at the duty ratio of 0.3. The sensing current is measured to be within 1 mA and follows to fit the order of the aspect ratio, between sensing and power FET.

• Steel and Composite Structures
• /
• v.29 no.4
• /
• pp.451-464
• /
• 2018

This paper presents some quasi-static tests for 4 mixed columns composed of CFST column and RC column. The seismic performance and failure mode were studied under low-cyclic revised loading. The failure mode was observed under different axial compression ratios. The hysteretic curve and skeleton curve were obtained. The effects of axial compression ratio on yield mechanism, displacement ductility, energy dissipation, stiffness and strength attenuation were analyzed. The results indicate that the failure behavior of CFST-RC mixed column with archaized style is mainly caused by bending failure and accompanied by some shear failure. The axial compression ratio performs a control function on the yielding order of the upper and lower columns. The yielding mechanism has a great influence on the ductility and energy dissipation capacity of specimens. Based on the experiment, finite element analysis was made to further research the seismic performance by ABAQUS software. The variable parameters were stiffness ratio of upper and lower columns, axial compression ratio, yielding strength of steel tube, concrete strength and rebar ratio. The simulation results show that with the increase of stiffness ratio of the upper and lower columns, the bearing capacity and ductility of specimens can correspondingly increase. As the axial compression ratio increases, the ductility of the specimen decreases gradually. The other three parameters both have positive effect on the bearing capacity but have negative effect on the ductility. The results can provide reference for the design and engineering application of mixed column consisted of CFST-RC in Chinese archaized buildings.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.9
• /
• pp.1646-1653
• /
• 2008

In this paper, we propose multicarrier CDMA system using the concept of the modulation level-controlled system in order to make the system robust to the frequency selectivity and to provide a maximum data rate maintaining an acceptable transmission quality over various channel environments. This system selects higher data rate when the channel experiences the low delay spread and slow fading. On the other hand, when the fading changes very fast and the delay spread is very long, the system selects lower data rate. In both cases, the system controls the number of serial-to-parallel converted streams and the number of fed streams. This system has the fixed number of sub-carriers. So the product of tile number of serial-to-parallel converted streams and the number of fed streams is always kept constant. With the same data fed at different sub-carriers, the frequency diversity is achieved. And a RAKE receiver also is utilized to achieve path (time) diversity.

• Korean Journal of Remote Sensing
• /
• v.18 no.6
• /
• pp.359-367
• /
• 2002

In this paper, a new embedded wavelet packet image coder algorithm is proposed for an effective image coder using correlation between partitioned coefficients. This new algorithm presents parent-child relationship for reducing image reconstruction error using relations between individual frequency sub-bands. By parent-child relationship, every coefficient is partitioned and encoded for the zerotree data structure. It is shown that the proposed wavelet packet image coder algorithm achieves low bit rates and rate-distortion. It also demonstrates higher PSNR under the same bit rate and an improvement in image compression time. The perfect rate control is compared with the conventional method. These results show that the encoding and decoding processes of the proposed coder are simpler and more accurate than the conventional ones for texture images that include many mid and high-frequency elements such as aerial and satellite photograph images. The experimental results imply the possibility that the proposed method can be applied to real-time vision system, on-line image processing and image fusion which require smaller file size and better resolution.

• Journal of Environmental Health Sciences
• /
• v.45 no.5
• /
• pp.474-486
• /
• 2019

Objectives: This study was performed to investigate the emission characteristics of aldehydes emitted by the printing industry and to evaluate their impact on adjacent residential areas. Methods: Aldehydes and THC were measured from the front of the control device in the printing and coating process. Aldehydes and ketones were measured by workplace area, residential area, and background area to evaluate their impact. Results: The concentrations of formaldehyde (<0.047 ppm) and acetaldehyde (<0.068 ppm) in the printing and coating process were relatively low, and the methyl ethyl ketone used as the primary solvent was the main carbonyl compound in the printing process. The daily mean concentrations of formaldehyde and acetaldehyde were not significantly different by workplace area, residential area, or background area. However, the concentration of methyl ethyl ketone was high in the order of workplace area, residential area, and background area. Conclusions: The concentrations of formaldehyde and acetaldehyde in the adjacent residential areas are considered to be more influenced by secondary sources of photochemical reactions than by primary sources. Methyl ethyl ketone is considered to be highly influenced by the primary source, which is printing facilities.