• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.133-138
• /
• 2011

To reduce the processing cost of the single grain REBCO (RE: Rare-earth elements) bulk superconductors, a cost-effective process should be developed. One possible way of developing the cost-effective process is the use of low-cost precursor powders. In this study, the single grain YBCO superconductors were fabricated using a home made powder. $YBa_2Cu_3O_{7-y}$ (Y123) powders were synthesized at $850-900^{\circ}C$ in air by the powder calcination method with repeated crushing and heat treatment steps. The processing parameters for the fabrication of single grain Y123 bulk superconductors, $T_{max}$ (maximum temperature), $T_p$ (peritectic temperature) and a cooling rate through $T_p$ were optimized. To enhance the flux pinning capacity of the single grain Y123 samples, $Y_2BaCuO_5$ (Y211) particles were dispersed in the Y123 matrix by adding $Y_2O_3$ powder to the calcined Y123 powder. Applying the optimized processing condition, the single grain Y123 superconductors with $T_c=91\;K$ and $J_c=1.5{\times}10^4\;A/cm^2$ at 2 T were successfully fabricated using a home made powder. The levitation forces and trapped magnetic field at 77 K measured using a Nd-B-Fe permanent magnet of 5300 G were 47 N and 3000 G, respectively, which are comparable to those obtained for the samples fabricated using a commercial grade Y123 powders.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.1
• /
• pp.5-8
• /
• 2005

MOD Process using metal acetates or trifluoroacetates has been considered to be a strong candidate for a low cost fabrication process for coated conductor with high $J_e$. Recently, an economical MOI) process has been developed for coated conductor with high $J_c$ using low cost starting materials such as YBCO powders. YBCO thin films prepared by single coating on LAO substrate with this modified oxide-precursor solution gives transport $I_c$ of 100A/cm-w and the $J_c$ value of $2.9MA/cm^{2}$ (77K, Self-field). The YBCO coated conductor prepared by single coating with $CeO_2/IBAD-YSZ/SS$ tape gives transport $I_c$ of 50A/cm-w in 2cm. Characterization with XRD, SEM shows that the YBCO layers were epitaxially grown and exhibit well-developed dense micro-structures. This newly developed oxide-precursor based MOD process will provide a low cost route to coated conductor with high $J_c$.

• Progress in Superconductivity
• /
• v.6 no.2
• /
• pp.142-145
• /
• 2005

YBCO coated conductors have been fabricated with a newly developed oxide-precursor-based MOD process. The precursor solution was synthesized with low cost YBCO powders as starting materials and YBCO coated conductors have been deposited on IBAD substrate ($CeO_2$/IBAD-YSZ/SS). YBCO coated conductor prepared by dip coating shows transport $I_c$ of 15A/cm-w at 77 K. Microstructural and crystallographic analyses indicate that YBCO layer was grown in epitaxy with substrate and exhibited well-developed dense microstructure. Also discussed are processing and analysis of YBCO coated conductor by slot-die web coating method. It was shown that this oxide-based MOD process provides a low cost route to coated conductor with high $J_c$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.4
• /
• pp.143-149
• /
• 2020

Calcium phosphates recognized as important bio-materials have been successfully synthesized by simple precipitation using waste abalone shells, which are rich mineral sources of calcium. Calcium hydroxide (Ca(OH)₂) originated from abalone shells was used as calcium source (precursor) for the preparation. Synthesis of calcium phosphates was performed by reacting calcium hydroxide with phosphoric acid (H₃PO₄) in aqueous solution. The initial precursor Ca/P ratios were adjusted to 1.50, 1.59 and 1.67, and the effect of the composition and the heat treatment on the synthesized powders and sintered bodies was investigated. The phases of the sintered ceramics prepared at 1150℃ were hydroxyapatite (HAp), β-tricalcium phosphate (β-TCP), and biphasic phosphate (HAp with β-TCP)), which were determined by the initial precursor Ca/P ratios. The results demonstrate the possibility for the synthesis of high value-added calcium phosphates from economical starting materials with low cost and high availability.