• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.165-171
• /
• 2010

The Homogeneous Charge Compression Ignition (HCCI) engine concept allows for both NOx and particulate matter to be reduced simultaneously, and it is a promising way to meet the next environmental challenges. Unfortunately, HCCI combustion often increases CO and HC emissions. The development of oxidation catalyst (OC) requires high conversion efficiency for CO and HC at low temperature. Conventional oxidation catalyst technologies may not be able to convert these emissions because of the saturation of active catalytic sites. The OC used in this study was 600 cpsi cordierite. Three kinds of OC with different amounts of Pt and Pd were used. The influence of the space velocity (SV), $H_2O$ and $O_2$ concentration was also studied. All types of OCs were found to have over 90% CO conversion efficiencies at $170^{\circ}C$. When in the presence of water vapor, CO conversion was increased, but $C_3H_8$ conversion was decreased. The performance of the OC was not influenced by initial the HC concentration. The 2Pt/Pd catalyst was better in terms of thermal aging than the Pt-only catalyst. The $LOT_{50}$ of both fresh and aged OC was increased with increasing SV and with the presence of $H_2O$.

• Journal of Biosystems Engineering
• /
• v.12 no.2
• /
• pp.16-27
• /
• 1987

Greenhouse farming was introduced to the Korean farmers in the middle of 1950's and its area has been increased annually. The plastic greenhouse, which is covered with polyethylene or polyvinyl chloride film, has been rapidly spread in greenhouse farming since 1970. The greenhouse farming greatly contributed to the increase of farm household income and the improvement of crop productivity per unit area. Since the greenhouse farming is generally practiced during winter, from November to March, the thermal environment in the plastic greenhouse should be controlled in order to maintain favorable condition for plant growing. Main factors that influence the thermal environment in the plastic greenhouse are solar radiation, convective and radiative heat transfer among the thermal component of the greenhouse, and the use of heat source. The objective of this study was to develop a simulation model for thermal environment of the plastic greenhouse in order to determine the characteristics of heat flow and effects of various ambient environmental conditions upon thermal environments within the plastic greenhouse. The results obtained are summarized as follows: 1. Simulation model for thermal environment of the plastic greenhouse was developed, resulting in a good agreement between the experimental and predicted data. 2. Solar radiation being absorbed in the plant and soil during the daytime was 75 percent of the total solar radiation and the remainder was absorbed in the plastic cover. 3. About 83 percent of the total heat loss was due to convective and radiative heat transfer through the plastic cover. Air ventilation heat loss was 5 to 6 percent of total heat loss during the daytime and 16 to 17 percent during the night. 4. The effectiveness of thermal curtain for the plastic greenhouse at night was significantly increased by the increase of the inside air temperature of the greenhouse due to the supplementary heat. 5. When the temperature difference between the inside and outside of the greenhouse was small, the variation of ambient wind velocity did not greatly affect on the inside air temperature. 6. The more solar radiation in the plastic greenhouse was, the higher the inside air temperature. Because of low heat storage capacity of the plant and soil inside the greenhouse and a relatively high convective heat loss through the plastic cover, the increase of solar radiation during the daytime could not reduce the supplymentary heat requirement for the greenhouse during the night.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.2
• /
• pp.47-55
• /
• 2016

In this study, WUA (Weighted Usable Area) based on the Instream Flow Incremental Methodology (IFIM) was calculated to determine ecological flow at JeonJu-Cheon by using River2D model. To calibrate River2D, simulation results for low flow conditions of River2D were compared with calibrated HEC-RAS simulation results and the optimum parameters were determined. The results were RMSE (0.18), NSE (0.71) and coefficient of determination (0.78) for velocity and RMSE (0.02), NSE (0.71), coefficient of determination (0.73) for water depth. The result shows that the model successfully simulates the water flows. A selected target fish species to build the habitat suitability index were composed of Zaccoplatypus and Coreoleuciscus splendidus. These species showed the highest occurrences over the past decade in f ish monitoring. Also, The WUA-Discharge curve was calculated with the suitability index in a medium flow conditions. From the result, WUA is changed according to flowrate. In the flowrate-WUA/A graph, ecological flow can be determined at $1.8{\sim}2.0m^3/s$ for Zaccoplatypus $2.0m^3/s$ and Coreoleuciscus splendidus $1.8m^3/s$ at JeonJu-Cheon upstream. When compared with flow-duration analysis, it is demonstrative that simulation results fitted ecological flow considering quantity of available habitat for each fish species.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.3B
• /
• pp.175-183
• /
• 2012

In this study, Galerkin scheme and SU/PG scheme of Petrov-Galerkin family were applied to the shallow water equations and a finite element model for shallow water flow was developed. Numerical simulations were conducted in several flumes with convection-dominated flow condition. Flow simulation of channel with slender structure in the water course revealed that Galerkin and SU/PG schemes showed similar results under very low Fr number and Re number condition. However, when the Fr number increased up to 1.58, Galerkin scheme did not converge while SU/PG scheme produced stable solutions after 5 iterations by Newton-Raphson method. For the transcritical flow simulation in diverging channel, the present model predicted the hydraulic jump accurately in terms of the jump location, the depth slope, and the flow depth after jump, and the numerical results showed good agreements with the hydraulic experiments carried out by Khalifa(1980). In the oblique hydraulic jump simulation, in which convection-dominated supercritical flow (Fr=2.74) evolves, Galerkin scheme blew up just after the first iteration of the initial time step. However, SU/PG scheme captured the boundary of oblique hydraulic jump accurately without numerical oscillation. The maximum errors quantified with exact solutions were less than 0.2% in water depth and velocity calculations, and thereby SU/PG scheme predicted the oblique hydraulic jump phenomena more accurately compared with the previous studies (Levin et al., 2006; Ricchiuto et al., 2007).

• Korean Journal of Environment and Ecology
• /
• v.28 no.3
• /
• pp.314-325
• /
• 2014

We studied fish fauna at 10 study sites in Ungcheon stream for 4 times from April to October, 2011 to investigate the influence of artificial structures such as dam (with fish-way) and weir (without fish-way), and abandoned mine on fish community. A total of 12 families, 36 species of fishes were collected. Dominant species was Zacco platypus (23.4%) and subdominant species was Zacco koreanus (20.5%). Ten species (27.8%) of Korean endemic species and Micropterus salmoides, exotic species, were observed during the study period. Endangered species of Korea such as Pseudopungtungia nigra and Liobagrus obesus, and Korean endemic species, Coreoperca herzi, which are vulnurable for water quality and had been observed in previous study, were not identified in this study. According to the cluster analysis, Ungcheon stream were divided into three groups consisting upstream (St.1, St.2, St.3), midstream (St.4, St.5, St.6, St.7), downstream (St.8, St.9, St.10). Community structure similarity between upper and lower site of Boryeong dam with fish-way (St.6-St.7) was high, whereas that of weir, lack of fish-way (St.7-St.8) showed little similarity indicating that fish-way was required. According to the canonical correlation analysis, high level of conductivity and salinity at upstream was detected and Misgurnus mizolepis, and endemic species of Korea such as Silurus microdorsalis, Coreoleuciscus splendidus and Iksookimia koreensis were observed at this part of the stream. Since Korean endemic species, Squalidus gracilis majimae cohabit with exotic species, M. Salmoides at downstream whose width is wide and water velocity is low, protection was needed for these endemic species.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.405-412
• /
• 2012

In the MCFC power generation system, the combustor supplies a high temperature mixture of gases to the cathode and heat to the reformer by using the off-gas from the anode; the off-gas includes high concentrations of $H_2O$ and $CO_2$. Since a combustor needs to be operated in a very lean condition and avoid local heating, a catalytic combustor is usually adopted. Catalytic combustion is also generally accepted as one of the environmentally preferred alternatives for generation of heat and power from fossil fuels because of its complete combustion and low emissions of pollutants such as CO, UHC, and $NO_x$. In this study, experiments were conducted on catalytic combustion behavior in the presence of Pd-based catalysts for the BOP (Balance Of Plant) of 5 kW MCFC (Molten Carbonate Fuel Cell) power generation systems. Extensive investigations were carried out on the catalyst performance with the gaseous $CH_4$ fuel by changing such various parameters as $H_2$ addition, inlet temperature, excess air ratio, space velocity, catalyst type, and start-up schedule of the pilot system adopted in the BOP.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.651-658
• /
• 2012

This paper concentrates on the evaluation of microcracks in thermal damaged concrete on the basis of the nonlinear ultrasonic modulation technique. Since concrete structure exposed to high temperature accompanies the development of microcracks due to the physical and chemical changes from temperature and exposed time, the adoption of nonlinear approach is required. Instead of using the conventional ultrasonic nondestructive methods which have the limitation in evaluating excessive microcracks, accordingly, a nonlinear ultrasonic modulation method which shows better sensitivity in quantifying microcracks is introduced. Upon the analysis for the modulation of ultrasonic wave and low frequency impact to measure the nonlinearity parameter, which can be used as an indicator of thermal damage, the verification processes for the introduced technique are followed: SEM investigation and permeable pore space test are performed to characterize thermally induced microcracks in concrete, and ultrasonic pulse velocity tests are performed to confirm the outstanding sensitivity of nonlinear ultrasonic modulation technique. In advance, compressive strength of thermal damaged concrete is measured to represent the effect of microcracks on performance degradation. Correlation studies between experimental data and measured data show that nonlinear ultrasonic modulation technique can effectively be used to quantify thermally induced microcracks, and to estimate the compressive strength of thermally damaged concrete.

• Publications of The Korean Astronomical Society
• /
• v.27 no.4
• /
• pp.297-298
• /
• 2012

ANIR (Atacama Near InfraRed camera) is a near infrared camera for the University of Tokyo Atacama 1m telescope, installed at the summit of Co. Chajnantor (5,640 m altitude) in northern Chile. The high altitude and extremely low water vapor (PWV = 0.5 mm) of the site enable us to perform observation of hydrogen $Pa{\alpha}$ emission line at $1.8751{\mu}m$. Since its first light observation in June 2009, we have been carrying out a $Pa{\alpha}$ narrow-band imaging survey of nearby luminous infrared galaxies (LIRGs), and have obtained $Pa{\alpha}$ for 38 nearby LIRGs listed in AKARI/FIS-PSC at the velocity of recession between 2,800 km/s and 8,100 km/s. LIRGs are affected by a large amount of dust extinction ($A_V$~ 3 mag), produced by their active star formation activities. Because $Pa{\alpha}$ is the strongest hydrogen recombination line in the infrared wavelength ranges, it is a good and direct tracer of dust-enshrouded star forming regions, and enables us to probe the star formation activities in LIRGs. We find that LIRGs have two star-forming modes. The origin of the two modes probably come from differences between merging stage and/or star-forming process.

• Journal of Aerospace System Engineering
• /
• v.14 no.5
• /
• pp.107-121
• /
• 2020

The performance analysis of the small satellites launch vehicle using the electric pump cycle as the upper stage engines was performed. The first stage is the launch vehicle that uses the test launch vehicle of the Korea Space Launch Vehicle II and the second stage employs elecpump cycle engine that uses liquid methane and kerosene (RP-1) as fuel. A model for the mass estimation was presented and the analysis was conducted for the range of thrust of 20 to 40 kN and combustion pressure of 3 to 6 MPa with a nozzle expansion ratio of 60 to 100. The mixture ratio with the maximum velocity increment was calculated and the performance of the LEO and SSO payload were calculated from the stage mass estimation. In both the cases, liquid methane, and RP-1 showed maximum payload for 20 kN thrust, 3 MPa combustion pressure, and the nozzle expansion ratio of 100, with a mixture ratio of 3.49 for liquid methane and 2.75 for RP-1. In addition, the ditching points of the first stage and the fairing in the LEO mission were analyzed using ASTOS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.383-388
• /
• 2020

This study aimed to identify the influence of the power components of the ammunition vehicle on the maximum speed. The maximum speeds of the engine and transmission changes were 3% and 1.7%, respectively. In the case of strong tension based on the track tension, the decrease was 4.6%. A 1.5% increase was obtained when the tension was weak. An examination of the maximum speed by dividing the track tension into six sections revealed the maximum speed to be highest when it was maintained below the middle. Experiments were performed by varying the orbital tension on both sides of the equipment. The maximum speed of the machine was affected by a large part of the tension. The maximum speed test was conducted by adjusting the tension at the driving test site. The results showed that when the tension was strong, the speed was 16.7% higher than the standard requirement. The speed was 28.3% at low tension. The influence of the maximum speed on the track tension was confirmed; the effect was greater than replacing the large parts.