• Journal of Powder Materials
• /
• v.22 no.3
• /
• pp.203-207
• /
• 2015

This study investigated the microstructure and wear resistance property of HPHT(high pressure high temperature) sintered PDC(polycrystalline diamond compact) in accordance with initial molding pressure. After quantifying an identical amount of diamond powder, the powder was inserted in top of WC-Co sintered material, and molded under four different pressure conditions (50, 100, 150, $200kgf/cm^2$). The obtained diamond compact underwent sintering in high pressure, high temperature conditions. In the case of the $50kgf/cm^2$ initial molding pressure condition, cracks were formed on the surface of PDC. On the other hand, PDCs obtained from $100{\sim}200kgf/cm^2$ initial molding pressure conditions showed a meticulous structure. As molding pressure increased, low Co composition within PDC was detected. A wear resistance test was performed on the PDC, and the $200kgf/cm^2$ condition PDC showed the highest wear resistance property.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.213-216
• /
• 1995

Strontium niobate, $Sr_2Nb_2O_{7}$ was prepared by the molten stilt synthesis (MSS) and the chemical coprecipitation method (CCP). Single phase $Sr_2Nb_2O_{7}$ was obtained by MSS and CCP at $750^{\circ}C$ and $800^{\circ}C$, respectively. An intermediate phase of composition, $Sr_{5}Nb_4O_{15}$, appeared at $700^{\circ}C$ when CCP method was employed. The resulting powder was observed to have finer particles and more uniform distribution of particle sizes, as compared to those obtained through the conventional method. Such powder characteristics allowed the use of a much lower sintering temperature of $1400^{\circ}C$. Grain-orientation along (0k0) direction, which is advantageous for improving dielectric properties, was also observed. The sintering characteristics and the dielectric properties prepared by MSS and CCP, were better than those by the conventional method.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.679-684
• /
• 2009

Phosphors of $Eu^{2+}$ doped alkaline earth aluminates MA$l_2O_4:Eu^{2+}$ (M=Sr, Ba, Ca) have been prepared by sol-gel process and their characterization of photoluminescence and photocurrent properties have been performed. The phosphors prepared by sol-gel process, due to its advantage of better homogeneity and low synthetic temperature, was synthesized as single phases at lower temperature than the solid-state process; $800{\sim}1000{^{\circ}C}$ for 6 h under mild reduction atmosphere (Ar- 3% $H_2$). It was confirmed that SrA$l_2O_4:Eu^{2+}$ composition revealed the most excellent properties in the brightness and photocurrent.

• Transactions of the Korean hydrogen and new energy society
• /
• v.6 no.1
• /
• pp.35-41
• /
• 1995

The MmNi-based alloy electrode was studied for use as a negative electrode in Ni-MH battery. Alloys with $MmNi_5-_xM_x$(M=Co,Al,Mn) composition were synthesized, and their electrode charateristics of activation rate, temperature dependence, electrode capacity and cycle life were investigated. With increasing Al content and decreasing Mn content in the alloys, the discharge capacity increased while the cycle life decreased. As x in $MmNi_5-_xM_x$ increased from 1.5 to 2.0, decreasing the Ni content, the discharge capacity, the low temperature property and the rate capability decreased. However its cycle life was improved. Increasing Co content resulted in a prolonged cycle life and decrease of high rate discharge capacity. It can be concluded that the most promising alloy in view of discharge capacity and cycle life is $MmNi_{3.5}Co_{0.7}Al_{0.5}Mn_{0.3}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.232-235
• /
• 2008

In this study, in order to develop the composition ceramics for multilayer piezoelectric actuator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3$, $Na_2CO_3$, ZnO as sintering aids and their piezoelectric and dielectric properties were investigated according to the Bi substitution, Bi substitution induced grain growth and increase of sinterablity, And also, Bi substitution suppress secondary phase due to the liquid phase sintering effect. Bi substitution enhanced electromechanical coupling factor ($k_p$) and dielectric constant ($\varepsilon_r$), However, mechanical quality factor($Q_m$) was deteriorated, At the sintering temperature of 870 $^{\circ}C$ and Bi substitution of 1 mol%, density, electromechanical coupling factor ($k_p$), mechanical quality factor ($Q_m$), Dielectric constant ($\varepsilon_r$) and piezoelectric constant ($d_{33}$) of specimen showed the optimum values of 7,878 $g/cm^3$, 0,608, 835, 1603 and 397 pC/N, respectively for multilayer piezoelectric actuator application.

• Progress in Superconductivity
• /
• v.13 no.1
• /
• pp.24-27
• /
• 2011

High voltage insulation in cryogenic environment is one of big issues for development of superconducting power application, such as superconducting fault current limiter, transformer, transmission cable, and so on. We had proposed a composite solid insulator composed of plastics and polymer insulation sheets for a use of high voltage superconducting power applications. It is well known that the G10 FRP keeps its mechanical strength at very low temperature and the PPLP is very good insulator adopted as insulations for superconducting transmission cables. The composition of these two materials will show very good electrical and mechanical properties adequate for the insulation components of superconducting power applications, such as bushing, insulation barrier, and even for a cryostat. Dielectric strengths of prepared samples were measured at the temperature of boiling point of liquid nitrogen at atmospheric pressure, which will be presented in this paper to show a usefulness of this technique.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.187-190
• /
• 1997

The aluminum-magnesium (Al-Mg) aklloys have been proved to be an effective solvent for synthesis of cubic-phase boron nitride (cBN) from hexagonal-phase boron nitride (hBN) at the conditions of high pressures and high temperatures (HP/HT). Various kinds of hBN powders having different crystallinity have been tested for cBN synthesis with Al-Mg solvents. The conversion ratio from hBN to cBN and the shape of synthesized cBN crystals appeared to be affected strongly by chemical composition and added amount of Al-Mg solvents as well as crystallinity of BN powders. As the magnesium content increased in the Al-Mg solvents, the conversion ratio increased and the size of cBN crystals became larger. The crystal facets developed well in the specimens with solvents having high Mg content. It was observed that a hBNlongrightarrowcBN transformation occurred more easily in the specimens having well crystallized hBN powders. Amorphous BN having much $B_2O_3$ impurity exhibited a low threshold temperature for transformation to cBN, which was attributed to crystallization of amorphous BN to well crystallized hBN prior to transformation into cBN with help of $B_2O_3$.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.2
• /
• pp.141-147
• /
• 2003

Oxidized polyethylene wax is obtained by oxidation of polyethylene wax and it is composed of various chemicals, e.g., fatty acid, alcohol, ketone and ester. The application of oxidized polyethylene wax is determined by the composition of these chemical substances. In this basic study we observed the basic reaction parameters of time, temperature, oxygen concentration and catalysts on the oxidation reaction of low molecular weight polyethylene(PE wax) by analyzing the acid value, physical and chemical properties of oxidized PE wax to develop a new oxidation process. Acid values are increased with temperature increase in the rage of $150^{\circ}C^{\sim}180^{\circ}C$ but decreased beyond 190$^{\circ}C$. Acid values are also increased with oxygen concentration. As the oxidation reaction proceeds the molecular weight and softening points of oxidation products are decreased by cracking reaction, but the viscosities are increased. To observe the crystallinity of oxidation products SEM experiment was performed. To obtain a high acid-value product in a mild condition, we adopted free radical catalysts and the acid value of the product using catalyst was higher than the product obtained without catalyst in the same reaction condition. The effective initiators were dicumyl peroxide(DCPO), t-butylperoxy-2-ethyl hexanoate(HOPO) and benzoyl peroxide(BPO) having long half-life.

• The Korean Journal of Ceramics
• /
• v.1 no.4
• /
• pp.179-184
• /
• 1995

Sodium superionic conductor (NASICON) compounds were prepared. The effects of sintering temperature and cooling rate on the formation and the distribution of crystalline NASICON and $ZrO_3$ second phase were investigated. In the von Alpen-type composition, the $ZrO_2$ second phase is in thermal equilibrium with the crystalline NASICON above $1320^{\circ}C$, but when cooled through 1260-$1320^{\circ}C$ crystalline NASICON was formed by reaction between $ZrO_2$ and liquid phase. Very slow cooling ($1^{\circ}C$/hr) to $1260^{\circ}C$ from sintering temperature decreased the amount of sodium which prevents the formation of the crystalline NASICON resulted high number of $ZrO_2$ grains near the surface of some sintered bodies. Maximum electrical conductivity of 0.200 ohm-1cm-1 was obtained at $300^{\circ}C$ for well-sintered samples with little $ZrO_3$. On the other hand, low conductivities were obtained for rapid-cooled samples which have less dense microstructure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.4
• /
• pp.229-233
• /
• 2015

In this paper, in order to develop outstanding Pb-free piezoelectric composition ceramics, the $(Na_{0.525}K_{0.443}Li_{0.037})(Nb_{0.883}Sb_{0.08}Ta_{0.037})O_3+0.3wt%Bi_2O_3+0.4wt%Fe_2O_3+xwt%CuO$ (x= 0~0.8 wt%)(abbreviated as NKL-NST) lead-free piezoelectric ceramics have been synthesized using the ordinary solid state reaction method. The effects of CuO-doping on the structure and electrical properties of the NKL-NST ceramics were systematically studied. The results show that the ceramics exhibit a pure perovskite structure with orthorhombic phase at room temperature, and secondary phase was found in the ceramics. The 0.4 wt%CuO added ceramics sintered at $950^{\circ}C$ showed the optimum properties of piezoelectric constant($d_{33}$), planar piezoelectric coupling coefficient(kp) and mechanical quality factor(Qm) : $d_{33}=213$[pC/N], kp= 0.43, Qm= 423,respectively.